User's Manual
Table Of Contents
- G-240WZ-A Product Guide
- Preface
- ETSI ONT safety guidelines
- ETSI environmental and CRoHS guidelines
- ANSI ONT safety guidelines
- Contents
- List of figures
- List of tables
- 1 — G-240WZ-A unit data sheet
- 1.1 G-240WZ-A part numbers and identification
- 1.2 G-240WZ-A general description
- 1.3 G-240WZ-A software and installation feature support
- 1.4 G-240WZ-A interfaces and interface capacity
- 1.5 G-240WZ-A LEDs
- 1.6 G-240WZ-A detailed specifications
- 1.7 G-240WZ-A GEM ports and T-CONTs
- 1.8 G-240WZ-A performance monitoring statistics
- 1.9 G-240WZ-A functional blocks
- 1.10 G-240WZ-A standards compliance
- 1.11 G-240WZ-A special considerations
- 2 — Install a G-240WZ-A indoor ONT
- 3 — Replace a G-240WZ-A indoor ONT
- 4 — Configure a G-240WZ-A indoor ONT
- 4.1 General
- 4.2 HGU mode GUI configuration
- Login
- Procedure 4-1 Login to web-based GUI
- Device and connection status
- Procedure 4-2 Device information retrieval
- Procedure 4-3 LAN status retrieval
- Procedure 4-4 WAN status retrieval
- Procedure 4-5 WAN status IPv6 retrieval
- Procedure 4-6 Home networking information retrieval
- Procedure 4-7 Optics module status retrieval
- Procedure 4-8 Voice information retrieval
- Network configuration
- Procedure 4-9 LAN networking configuration
- Procedure 4-10 LAN IPv6 networking configuration
- Procedure 4-11 WAN networking configuration
- Procedure 4-12 WAN DHCP configuration
- Procedure 4-13 WiFi 2.4G networking configuration
- Procedure 4-14 WiFi 5G networking configuration
- Procedure 4-15 Routing configuration
- Procedure 4-16 DNS configuration
- Procedure 4-17 TR-069 configuration
- Security configuration
- Procedure 4-18 Firewall configuration
- Procedure 4-19 MAC filter configuration
- Procedure 4-20 IP filter configuration
- Procedure 4-21 DMZ and ALG configuration
- Application configuration
- Procedure 4-22 Port forwarding configuration
- Procedure 4-23 DDNS configuration
- Procedure 4-24 NTP configuration
- Procedure 4-25 USB storage configuration
- Procedure 4-26 UPnP and DLNA configuration
- Maintenance
- Procedure 4-27 Password configuration
- Procedure 4-28 SLID configuration
- Procedure 4-29 Device management
- Procedure 4-30 Backup and restore
- Procedure 4-31 Upgrade firmware
- Procedure 4-32 Reboot ONT
- Procedure 4-33 Restore factory defaults
- Procedure 4-34 Diagnose connections
- Procedure 4-35 View log files
- RG troubleshooting counters
- Procedure 4-36 Retrieve Residential Gateway (RG) troubleshooting counters
- Smart Home configuration
- Procedure 4-37 Configure home monitoring systems
- 4.3 SFU mode configuration
- Switch from default HGU mode to SFU mode
- Procedure 4-38 Switching to SFU mode
- Procedure 4-39 Modifying the operator ID
- Login
- Procedure 4-40 Login to web-based GUI
- Device and connection status
- Procedure 4-41 Device information retrieval
- Maintenance
- Procedure 4-42 Password configuration
- Procedure 4-43 LOID configuration
- Procedure 4-44 SLID configuration
- 5 — ONT configuration file over OMCI
4 — Configure a G-240WZ-A indoor ONT
Alcatel-Lucent 7368 ISAM ONT 4-27
Edition 01
G-240WZ-A Product Guide
3 Click Add.
4 STOP. This procedure is complete.
Procedure 4-21 DMZ and ALG configuration
1 Select Security > DMZ and ALG from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-21.
Figure 4-21 DMZ and ALG window
Table 4-20 describes the fields in the DMZ and ALG window.
Table 4-20 DMZ and ALG parameters
2 Configure ALG.
3 Click Save ALG.
4 Configure DMZ.
Field Description
ALG Config Select the checkboxes to enable the protocols to be supported by the ALG:
FTP, TFTP, SIP, H323, RTSP, L2TP, IPSEC, PPTP
DMZ Config
WAN Connection
List
Choose a WAN connection from the drop-down menu
Enable DMZ Select this checkbox to enable DMZ on the chosen WAN connection
DMZ IP Address Choose Customer Setting and enter the DMZ IP address or choose the IP
address of a connected device from the drop-down menu
R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01