User's Manual
Table Of Contents
- G-240WZ-A Product Guide
- Preface
- ETSI ONT safety guidelines
- ETSI environmental and CRoHS guidelines
- ANSI ONT safety guidelines
- Contents
- List of figures
- List of tables
- 1 — G-240WZ-A unit data sheet
- 1.1 G-240WZ-A part numbers and identification
- 1.2 G-240WZ-A general description
- 1.3 G-240WZ-A software and installation feature support
- 1.4 G-240WZ-A interfaces and interface capacity
- 1.5 G-240WZ-A LEDs
- 1.6 G-240WZ-A detailed specifications
- 1.7 G-240WZ-A GEM ports and T-CONTs
- 1.8 G-240WZ-A performance monitoring statistics
- 1.9 G-240WZ-A functional blocks
- 1.10 G-240WZ-A standards compliance
- 1.11 G-240WZ-A special considerations
- 2 — Install a G-240WZ-A indoor ONT
- 3 — Replace a G-240WZ-A indoor ONT
- 4 — Configure a G-240WZ-A indoor ONT
- 4.1 General
- 4.2 HGU mode GUI configuration
- Login
- Procedure 4-1 Login to web-based GUI
- Device and connection status
- Procedure 4-2 Device information retrieval
- Procedure 4-3 LAN status retrieval
- Procedure 4-4 WAN status retrieval
- Procedure 4-5 WAN status IPv6 retrieval
- Procedure 4-6 Home networking information retrieval
- Procedure 4-7 Optics module status retrieval
- Procedure 4-8 Voice information retrieval
- Network configuration
- Procedure 4-9 LAN networking configuration
- Procedure 4-10 LAN IPv6 networking configuration
- Procedure 4-11 WAN networking configuration
- Procedure 4-12 WAN DHCP configuration
- Procedure 4-13 WiFi 2.4G networking configuration
- Procedure 4-14 WiFi 5G networking configuration
- Procedure 4-15 Routing configuration
- Procedure 4-16 DNS configuration
- Procedure 4-17 TR-069 configuration
- Security configuration
- Procedure 4-18 Firewall configuration
- Procedure 4-19 MAC filter configuration
- Procedure 4-20 IP filter configuration
- Procedure 4-21 DMZ and ALG configuration
- Application configuration
- Procedure 4-22 Port forwarding configuration
- Procedure 4-23 DDNS configuration
- Procedure 4-24 NTP configuration
- Procedure 4-25 USB storage configuration
- Procedure 4-26 UPnP and DLNA configuration
- Maintenance
- Procedure 4-27 Password configuration
- Procedure 4-28 SLID configuration
- Procedure 4-29 Device management
- Procedure 4-30 Backup and restore
- Procedure 4-31 Upgrade firmware
- Procedure 4-32 Reboot ONT
- Procedure 4-33 Restore factory defaults
- Procedure 4-34 Diagnose connections
- Procedure 4-35 View log files
- RG troubleshooting counters
- Procedure 4-36 Retrieve Residential Gateway (RG) troubleshooting counters
- Smart Home configuration
- Procedure 4-37 Configure home monitoring systems
- 4.3 SFU mode configuration
- Switch from default HGU mode to SFU mode
- Procedure 4-38 Switching to SFU mode
- Procedure 4-39 Modifying the operator ID
- Login
- Procedure 4-40 Login to web-based GUI
- Device and connection status
- Procedure 4-41 Device information retrieval
- Maintenance
- Procedure 4-42 Password configuration
- Procedure 4-43 LOID configuration
- Procedure 4-44 SLID configuration
- 5 — ONT configuration file over OMCI
4 — Configure a G-240WZ-A indoor ONT
4-26 Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240WZ-A Product Guide
Procedure 4-20 IP filter configuration
1 Select Security > IP filter from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-20.
Figure 4-20 IP filter window
Table 4-19 describes the fields in the IP filter window.
Table 4-19 IP filter parameters
2 Configure the IP filter.
Field Description
Enable IP Filter Select this checkbox to enable an IP filter
Mode Choose an IP filter mode from the drop-down menu:
• Drop for upstream
• Drop for downstream
Internal Client Choose an internal client from the drop-down menu:
• Customer setting - uses the IP address input below
• IP - uses the connecting devices' IP to the ONT
Local IP Address Local IP address
Source Subnet
Mask
Source subnet mask
Remote IP Address Remote IP address
Destination Subnet
Mask
Destination subnet mask
Protocol Choose an application protocol or all from the drop-down menu
R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01