User's Manual
Table Of Contents
- G-240WZ-A Product Guide
- Preface
- ETSI ONT safety guidelines
- ETSI environmental and CRoHS guidelines
- ANSI ONT safety guidelines
- Contents
- List of figures
- List of tables
- 1 — G-240WZ-A unit data sheet
- 1.1 G-240WZ-A part numbers and identification
- 1.2 G-240WZ-A general description
- 1.3 G-240WZ-A software and installation feature support
- 1.4 G-240WZ-A interfaces and interface capacity
- 1.5 G-240WZ-A LEDs
- 1.6 G-240WZ-A detailed specifications
- 1.7 G-240WZ-A GEM ports and T-CONTs
- 1.8 G-240WZ-A performance monitoring statistics
- 1.9 G-240WZ-A functional blocks
- 1.10 G-240WZ-A standards compliance
- 1.11 G-240WZ-A special considerations
- 2 — Install a G-240WZ-A indoor ONT
- 3 — Replace a G-240WZ-A indoor ONT
- 4 — Configure a G-240WZ-A indoor ONT
- 4.1 General
- 4.2 HGU mode GUI configuration
- Login
- Procedure 4-1 Login to web-based GUI
- Device and connection status
- Procedure 4-2 Device information retrieval
- Procedure 4-3 LAN status retrieval
- Procedure 4-4 WAN status retrieval
- Procedure 4-5 WAN status IPv6 retrieval
- Procedure 4-6 Home networking information retrieval
- Procedure 4-7 Optics module status retrieval
- Procedure 4-8 Voice information retrieval
- Network configuration
- Procedure 4-9 LAN networking configuration
- Procedure 4-10 LAN IPv6 networking configuration
- Procedure 4-11 WAN networking configuration
- Procedure 4-12 WAN DHCP configuration
- Procedure 4-13 WiFi 2.4G networking configuration
- Procedure 4-14 WiFi 5G networking configuration
- Procedure 4-15 Routing configuration
- Procedure 4-16 DNS configuration
- Procedure 4-17 TR-069 configuration
- Security configuration
- Procedure 4-18 Firewall configuration
- Procedure 4-19 MAC filter configuration
- Procedure 4-20 IP filter configuration
- Procedure 4-21 DMZ and ALG configuration
- Application configuration
- Procedure 4-22 Port forwarding configuration
- Procedure 4-23 DDNS configuration
- Procedure 4-24 NTP configuration
- Procedure 4-25 USB storage configuration
- Procedure 4-26 UPnP and DLNA configuration
- Maintenance
- Procedure 4-27 Password configuration
- Procedure 4-28 SLID configuration
- Procedure 4-29 Device management
- Procedure 4-30 Backup and restore
- Procedure 4-31 Upgrade firmware
- Procedure 4-32 Reboot ONT
- Procedure 4-33 Restore factory defaults
- Procedure 4-34 Diagnose connections
- Procedure 4-35 View log files
- RG troubleshooting counters
- Procedure 4-36 Retrieve Residential Gateway (RG) troubleshooting counters
- Smart Home configuration
- Procedure 4-37 Configure home monitoring systems
- 4.3 SFU mode configuration
- Switch from default HGU mode to SFU mode
- Procedure 4-38 Switching to SFU mode
- Procedure 4-39 Modifying the operator ID
- Login
- Procedure 4-40 Login to web-based GUI
- Device and connection status
- Procedure 4-41 Device information retrieval
- Maintenance
- Procedure 4-42 Password configuration
- Procedure 4-43 LOID configuration
- Procedure 4-44 SLID configuration
- 5 — ONT configuration file over OMCI
4 — Configure a G-240WZ-A indoor ONT
4-2 Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240WZ-A Product Guide
4.1 General
Please refer to the configuration information provided with your OLT for the
software configuration procedure for a G-240WZ-A ONT.
For HTTP configuration procedures, please refer to the 7368 ISAM ONT
Configuration, Management, and Troubleshooting Guide.
4.2 HGU mode GUI configuration
Use the procedures below to use the web-based GUI for the G-240WZ-A in HGU
mode. This mode is preset at delivery.
A home gateway unit (HGU) is a home networking device, used as a gateway to
connect devices in the home through fiber to the Internet. An HGU provides a variety
of features for the home network including routing and firewall capability. By using
the HGU, users can connect all smart equipment in their home, including personal
computers, set-top boxes, mobile phones, and other consumer electronics devices, to
the Internet.
Login
Use the procedure below to login to the web-based GUI for the G-240WZ-A.
Procedure 4-1 Login to web-based GUI
1 Open a web browser and enter the IP address of the ONT in the address bar.
The login window appears.
The default gateway IP address is http://192.168.1.254. You can connect to this
IP address using your web browser after connecting your PC to one of Ethernet
ports of the ONT. The static IP address of your PC must be in the same 192.168.1.x
subnet as the ONT.
2 Enter your username and password in the Log in window, as shown in Figure 4-1.
The default username and password are printed on the ONT. The default user
name is userAdmin. The default superuser name is AdminGPON. Contact
Alcatel-Lucent for the superuser password.
R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01