User's Manual
Table Of Contents
- G-240WZ-A Product Guide
- Preface
- ETSI ONT safety guidelines
- ETSI environmental and CRoHS guidelines
- ANSI ONT safety guidelines
- Contents
- List of figures
- List of tables
- 1 — G-240WZ-A unit data sheet
- 1.1 G-240WZ-A part numbers and identification
- 1.2 G-240WZ-A general description
- 1.3 G-240WZ-A software and installation feature support
- 1.4 G-240WZ-A interfaces and interface capacity
- 1.5 G-240WZ-A LEDs
- 1.6 G-240WZ-A detailed specifications
- 1.7 G-240WZ-A GEM ports and T-CONTs
- 1.8 G-240WZ-A performance monitoring statistics
- 1.9 G-240WZ-A functional blocks
- 1.10 G-240WZ-A standards compliance
- 1.11 G-240WZ-A special considerations
- 2 — Install a G-240WZ-A indoor ONT
- 3 — Replace a G-240WZ-A indoor ONT
- 4 — Configure a G-240WZ-A indoor ONT
- 4.1 General
- 4.2 HGU mode GUI configuration
- Login
- Procedure 4-1 Login to web-based GUI
- Device and connection status
- Procedure 4-2 Device information retrieval
- Procedure 4-3 LAN status retrieval
- Procedure 4-4 WAN status retrieval
- Procedure 4-5 WAN status IPv6 retrieval
- Procedure 4-6 Home networking information retrieval
- Procedure 4-7 Optics module status retrieval
- Procedure 4-8 Voice information retrieval
- Network configuration
- Procedure 4-9 LAN networking configuration
- Procedure 4-10 LAN IPv6 networking configuration
- Procedure 4-11 WAN networking configuration
- Procedure 4-12 WAN DHCP configuration
- Procedure 4-13 WiFi 2.4G networking configuration
- Procedure 4-14 WiFi 5G networking configuration
- Procedure 4-15 Routing configuration
- Procedure 4-16 DNS configuration
- Procedure 4-17 TR-069 configuration
- Security configuration
- Procedure 4-18 Firewall configuration
- Procedure 4-19 MAC filter configuration
- Procedure 4-20 IP filter configuration
- Procedure 4-21 DMZ and ALG configuration
- Application configuration
- Procedure 4-22 Port forwarding configuration
- Procedure 4-23 DDNS configuration
- Procedure 4-24 NTP configuration
- Procedure 4-25 USB storage configuration
- Procedure 4-26 UPnP and DLNA configuration
- Maintenance
- Procedure 4-27 Password configuration
- Procedure 4-28 SLID configuration
- Procedure 4-29 Device management
- Procedure 4-30 Backup and restore
- Procedure 4-31 Upgrade firmware
- Procedure 4-32 Reboot ONT
- Procedure 4-33 Restore factory defaults
- Procedure 4-34 Diagnose connections
- Procedure 4-35 View log files
- RG troubleshooting counters
- Procedure 4-36 Retrieve Residential Gateway (RG) troubleshooting counters
- Smart Home configuration
- Procedure 4-37 Configure home monitoring systems
- 4.3 SFU mode configuration
- Switch from default HGU mode to SFU mode
- Procedure 4-38 Switching to SFU mode
- Procedure 4-39 Modifying the operator ID
- Login
- Procedure 4-40 Login to web-based GUI
- Device and connection status
- Procedure 4-41 Device information retrieval
- Maintenance
- Procedure 4-42 Password configuration
- Procedure 4-43 LOID configuration
- Procedure 4-44 SLID configuration
- 5 — ONT configuration file over OMCI
4 — Configure a G-240WZ-A indoor ONT
4-38 Alcatel-Lucent 7368 ISAM ONT
Edition 01
G-240WZ-A Product Guide
Procedure 4-33 Restore factory defaults
1 Select Maintain > Factory Default from the top-level menu in the GPON Home
Gateway window, as shown in Figure 4-33.
Figure 4-33 Factory default window
2 Click Factory Default to reset the ONT to its factory default settings.
3 STOP. This procedure is complete.
R05.04.00 | March 2016 | 3FE-45933-AAAA-TCZZA | Edition 01