7368 ISAM ONT G-240W-F Product Guide AF T 7368 Intelligent Services Access Manager ONT D R 7368 ISAM ONT G-240W-F Product Guide Edition 01 Issue: 01 Nokia — Proprietary and confidential Use pursuant to applicable agreements
7368 ISAM ONT G-240W-F Product Guide Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners. The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein. © 2017 Nokia.
7368 ISAM ONT G-240W-F Product Guide Preface 1 Preface This preface provides general information about the documentation set for optical network terminals (ONTs). 1.1 Scope 1.2 AF T This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures for the current release.
Preface 7368 ISAM ONT G-240W-F Product Guide 1.6 Nokia quality processes Nokia’s ONT quality practices are in compliance with TL 9000 requirements. These requirements are documented in the Fixed Networks Quality Manual 3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met.
7368 ISAM ONT G-240W-F Product Guide Procedure 2 Preface To access individual documents Individual PDFs of customer documents are also accessible through the Nokia Customer Support website. Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you are a new user and require access to this service, please contact your Nokia sales representative. 2 From the Technical Content for drop-down menu, choose the product.
Preface 7368 ISAM ONT G-240W-F Product Guide 1.9.1 Procedures with options or substeps When there are options in a procedure, they are identified by letters. When there are required substeps in a procedure, they are identified by roman numerals. Procedure 3 Example of options in a procedure At step 1, you can choose option a or b. At step 2, you must do what the step indicates. 2 Procedure 4 This step offers two options. You must choose one of the following: a This is one option.
368 ISAM ONT G-240W-F Product Guide 1.10 Preface Multiple PDF document search You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel. The results are grouped by PDF file, and you can expand the entry for each file. Note — The PDF files in which you search must be in the same folder. To search multiple PDF files for a common term 1 2 3 4 5 6 AF T Procedure 5 Open Adobe Acrobat Reader.
7368 ISAM ONT G-240W-F Product Guide D R AF T Preface 8 Edition 01 Issue: 01
7368 ISAM ONT G-240W-F Product Guide Table of contents Preface.............................................................................................3 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.9.1 1.10 Scope ..........................................................................................................3 Audience......................................................................................................3 Required knowledge.............................................................
7368 ISAM ONT G-240W-F Product Guide ONT environmental requirements .............................................................30 Storage ......................................................................................................30 Transportation ...........................................................................................30 Stationary use............................................................................................30 Thermal limitations ............................
7368 ISAM ONT G-240W-F Product Guide G-240W-F standards compliance..............................................................62 Energy-related products standby and off modes compliance....................63 G-240W-F special considerations .............................................................63 Wi-Fi service..............................................................................................63 Wi-Fi physical features .......................................................................
D R AF T 7368 ISAM ONT G-240W-F Product Guide 12 Edition 01 Issue: 01
7368 ISAM ONT G-240W-F Product Guide List of figures 2 ETSI ONT safety guidelines .........................................................17 Figure 1 Figure 2 Figure 3 Figure 4 PSE certification ........................................................................................19 Laser product label ....................................................................................22 Laser classification label............................................................................
7368 ISAM ONT G-240W-F Product Guide Home networking information window.......................................................90 Optics module status window ....................................................................91 Voice Information window..........................................................................93 LAN network window .................................................................................95 LAN IPv6 network window........................................................
7368 ISAM ONT G-240W-F Product Guide List of tables 2 ETSI ONT safety guidelines .........................................................17 Table 1 Safety labels ..............................................................................................18 4 ANSI ONT safety guidelines ........................................................33 Table 2 Safety labels ..............................................................................................34 G-240W-F unit data sheet............
7368 ISAM ONT G-240W-F Product Guide 9 URL Filter parameters .............................................................................120 Parental control parameters ....................................................................121 DMZ and ALG parameters ......................................................................122 Access control parameters ......................................................................123 Port forwarding parameters ............................................
7368 ISAM ONT G-240W-F Product Guide ETSI ONT safety guidelines 2 ETSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals (ONTs). 2.1 Safety instructions 2.1.1 AF T This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. Safety instruction boxes The safety instruction boxes are provided in the ONT customer documentation.
ETSI ONT safety guidelines 7368 ISAM ONT G-240W-F Product Guide The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. AF T The following is an example of the Note box. Note — Information of special interest.
7368 ISAM ONT G-240W-F Product Guide Figure 1 ETSI ONT safety guidelines PSE certification This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Warning AF T 19841 2.
ETSI ONT safety guidelines 2.2.3 7368 ISAM ONT G-240W-F Product Guide Environmental standard compliance The ONT equipment complies with the EN 300 019 European environmental standards. 2.2.4 Laser product standard compliance 2.2.5 AF T For most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2 for laser products. If there is an exception to this compliance regulation, you can find this information in the standards compliance section of the unit data sheet in this Product Guide.
7368 ISAM ONT G-240W-F Product Guide 2.3.1 ETSI ONT safety guidelines Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. 2.3.2 Cabling AF T The following are the guidelines regarding cables used for the ONT equipment: • All cables must be approved by the relevant national electrical code.
ETSI ONT safety guidelines 7368 ISAM ONT G-240W-F Product Guide Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system. Danger — There may be invisible laser radiation at the fiber optic cable when the cable is removed from the connector. Avoid direct exposure to the laser beam. Observe the following danger for laser hazard. Eyes can be damaged when they are exposed to a laser beam.
7368 ISAM ONT G-240W-F Product Guide Laser classification label CLASS 1 LASER PRODUCT ' PRODUCTO LASER CLASE 1 ' CLASE 1 DEL LASER LASER CLASSE 1 AF T Figure 3 ETSI ONT safety guidelines 18992 Figure 4 shows a laser warning label and an explanatory label for laser products. Labels and warning may be provided in other languages.
ETSI ONT safety guidelines 7368 ISAM ONT G-240W-F Product Guide Figure 4 Laser warning labels INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label AF T Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER.
7368 ISAM ONT G-240W-F Product Guide 2.5.4 ETSI ONT safety guidelines Location class Use cable supports and guides to protect the receptacles from strain. 2.6 Environmental requirements See the ONT technical specification documentation for more information about temperature ranges. AF T During operation in the supported temperature range, condensation inside the ONT caused by humidity is not an issue.
7368 ISAM ONT G-240W-F Product Guide D R AF T ETSI ONT safety guidelines 26 Edition 01 Issue: 01
7368 ISAM ONT G-240W-F Product Guide ETSI environmental and CRoHS guidelines 3 ETSI environmental and CRoHS guidelines This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line termination (OLT) and optical network termination (ONT) systems. This chapter also includes environmental operation parameters of general interest. Environmental labels AF T 3.
ETSI environmental and CRoHS guidelines 3.1.2.2 Products below MCV value label AF T Figure 5 7368 ISAM ONT G-240W-F Product Guide 18986 Products containing hazardous substances above Maximum Concentration Value (MCV) label D R Figure 6 shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products).
7368 ISAM ONT G-240W-F Product Guide Products above MCV value label AF T Figure 6 ETSI environmental and CRoHS guidelines 18985 R Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories.
ETSI environmental and CRoHS guidelines 3.3 7368 ISAM ONT G-240W-F Product Guide Other environmental requirements Observe the following environmental requirements when handling the P-OLT or ONT equipment. 3.3.1 ONT environmental requirements AF T See the ONT technical specification documentation for more information about temperature ranges. 3.3.2 Storage According to ETS 300-019-1-1 - Class 1.1, storage of OLT equipment must be in Class 1.1, weather-protected, temperature-controlled locations.
7368 ISAM ONT G-240W-F Product Guide 3.3.6 ETSI environmental and CRoHS guidelines Material content compliance European Union (EU) Directive 2002/95/EC, “Restriction of the use of certain Hazardous Substances” (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment.
ETSI environmental and CRoHS guidelines 7368 ISAM ONT G-240W-F Product Guide At the end of their life, the OLT and ONT products are subject to the applicable local legislations that implement the European Directive 2012/19EU on waste electrical and electronic equipment (WEEE). There can be different requirements for collection and treatment in different member states of the European Union.
7368 ISAM ONT G-240W-F Product Guide ANSI ONT safety guidelines 4 ANSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals or units (ONTs or ONUs) in the North American or ANSI market. 4.1 Safety instructions 4.1.1 AF T This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment.
ANSI ONT safety guidelines 7368 ISAM ONT G-240W-F Product Guide The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. AF T The following is an example of the Note box. Note — Information of special interest.
7368 ISAM ONT G-240W-F Product Guide ANSI ONT safety guidelines Description Label text Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canadian standard compliance (modular ONT) This Class A digital apparatus complies with Canadian ICES-003.
ANSI ONT safety guidelines 4.2.
7368 ISAM ONT G-240W-F Product Guide 4.2.
ANSI ONT safety guidelines 4.2.5 7368 ISAM ONT G-240W-F Product Guide Resistibility requirements compliance The ONT equipment complies with the requirements of ITU Recommendation K.21 for resistibility of telecommunication equipment installed in customer premises to overvoltage and overcurrents. 4.3 Laser safety guidelines AF T Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system.
7368 ISAM ONT G-240W-F Product Guide Figure 10 ANSI ONT safety guidelines Laser product label 18455 AF T Figure 11 shows a laser classification label. Laser classification labels may be provided in other languages. Figure 11 Laser classification label ' PRODUCTO LASER CLASE 1 ' CLASE 1 DEL LASER LASER CLASSE 1 18992 R CLASS 1 LASER PRODUCT Figure 12 shows a laser warning label and an explanatory label for laser products. Explanatory labels may be provided in other languages.
ANSI ONT safety guidelines Figure 12 7368 ISAM ONT G-240W-F Product Guide Laser warning labels INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label AF T Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER.
7368 ISAM ONT G-240W-F Product Guide Figure 13 ANSI ONT safety guidelines Sample laser product safety label on the ONT equipment Model: MFG: MONTH: XX YEAR: XXXX ICS: XX MRev: XX 3FE55851ABAA MAC:XXXXXXXXXXXX SN:ALCLXXXXXXXX I.T.E CLASS 1 LASER PRODUCT PRODUIT LASER DE CLASSE 1 Intertek 4006119 AF T FCC ID: XXXXXXXXXXX 12VDC 3A ASSEMBLED IN CHINA 2301 Sugar Bush Rd. Raleigh, NC 27612 This device complies with Part 15 of the FCC Rule.
ANSI ONT safety guidelines 4.4 7368 ISAM ONT G-240W-F Product Guide Electrical safety guidelines This section provides the electrical safety guidelines for the ONT equipment. Note — The ONTs comply with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards. Power supplies AF T 4.4.1 The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia.
7368 ISAM ONT G-240W-F Product Guide ANSI ONT safety guidelines During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD. Nokia recommends that you prepare the site before you install the ONT equipment. In addition, you must control relative humidity, use static dissipating material for furniture or flooring, and restrict the use of air conditioning. 4.
7368 ISAM ONT G-240W-F Product Guide D R AF T ANSI ONT safety guidelines 44 Edition 01 Issue: 01
7368 ISAM ONT G-240W-F Product Guide G-240W-F unit data sheet 5 G-240W-F unit data sheet 5.1 G-240W-F part numbers and identification 5.2 G-240W-F general description 5.3 G-240W-F software and installation feature support 5.4 G-240W-F interfaces and interface capacity AF T 5.5 G-240W-F LEDs 5.6 G-240W-F detailed specifications 5.7 G-240W-F GEM ports and T-CONTs 5.8 G-240W-F performance monitoring statistics 5.9 G-240W-F functional blocks 5.10 G-240W-F standards compliance D R 5.
G-240W-F unit data sheet 5.1 7368 ISAM ONT G-240W-F Product Guide G-240W-F part numbers and identification Table 3 provides part numbers and identification information for the G-240W-F indoor ONT. Table 3 Identification of G-240W-F indoor ONTs Provisioning part number Description CLEI CPR ECI/ Bar code 3FE 46649 AA 3FE 46597 AA Package P GPON indoor ONT with two POTS ports, four 10/100/1000 Base-T Ethernet interfaces, and one 100 mW Wi-Fi radio with on/off switch.
7368 ISAM ONT G-240W-F Product Guide G-240W-F unit data sheet Ordering kit part number Provisioning part number Description CLEI CPR ECI/ Bar code 3FE 46649 BB 3FE 46597 AB Package P GPON indoor ONT with two POTS ports, four 10/100/1000 Base-T Ethernet interfaces, and one 100 mW Wi-Fi radio with on/off switch. — — — — — — Customer-specific This ONT features two USB 2.0 ports and supports SC/APC optics.
G-240W-F unit data sheet 7368 ISAM ONT G-240W-F Product Guide • • • • • • • • • • 5.2.1 AF T 2.4 GHz wireless interface 2 5dBI indoor multi-directional external WiFi antenna (not detachable) MIMO support for up to 20 concurrent wireless connections 802.11b/g/n compliant MDI/MDIX auto sensing auto-negotiation for speed and duplex multiple voice Codec echo cancellation Analog Telephone Adapter (ATA) function integrated based on SIP (RFC3261) and H.
7368 ISAM ONT G-240W-F Product Guide 5.2.2 G-240W-F unit data sheet TR-104 parameter extension support for voice service A proprietary attribute has been added to the TR-104 Voice Service object structure to enable the ACS to configure the name of the embedded GSIP XML file to be selected. The TR-104 Voice Service Object is: InternetGatewayDevice.Services.VoiceService.{i}.Capabilities.SIP. 5.2.3 AF T The proprietary attribute is: X_ALU-COM_XML_File_Name_Path.
G-240W-F unit data sheet 7368 ISAM ONT G-240W-F Product Guide EAP-SIM is an authentication method that uses the user credentials on the SIM card and EAP to authenticate the user with the Wi-Fi network, removing the need for user input (username and password). A dedicated public mobile offload SSID in the ONT enables mobile subscribers to connect to the Internet. Encryption is supported by 802.11, providing seamless Wi-Fi authentication for SIM-based user equipment. 5.2.
7368 ISAM ONT G-240W-F Product Guide 5.2.6.1 G-240W-F unit data sheet GRE Generic Routing Encapsulation (GRE) is a tunneling protocol that can encapsulate a wide variety of network layer protocols inside virtual point-to-point links over an Internet Protocol network. GRE provides a secure path for transporting packets through a public network. In essence, GRE creates a private P2P connection, similar to a VPN, between clients and servers.
G-240W-F unit data sheet 7368 ISAM ONT G-240W-F Product Guide Figure 14 SoftGRE-based architecture Viurs scanner Security TR-069 VLAN: 881 VSR Motive Basic vCPE Diag.
7368 ISAM ONT G-240W-F Product Guide • • • • • • 5.
G-240W-F unit data sheet G-240W-F indoor ONT physical connections (back view) AF T Figure 15 7368 ISAM ONT G-240W-F Product Guide Figure 16 shows the buttons on the side of the G-240W-F indoor ONTS: reset, LED indicators on/off, WLAN enable/disable, and WPS enable/disable, as well as the fiber optic port on the bottom of the ONT.
7368 ISAM ONT G-240W-F Product Guide G-240W-F unit data sheet Table 5 describes the physical connections for G-240W-F indoor ONTs. Table 5 G-240W-F indoor ONT physical connections Connection (1) Description USB This connection is provided through two USB 2.0 ports on the back of the ONT. (USB port)s The voltage rate is 5V, and the current rate is 500mA per port. LAN1-LAN4 This connection is provided through Ethernet RJ-45 connectors on the back of the ONT.
G-240W-F unit data sheet G-240W-F indoor ONT LEDs AF T Figure 17 7368 ISAM ONT G-240W-F Product Guide Table 6 provides LED descriptions for G-240W-F indoor ONTs.
7368 ISAM ONT G-240W-F Product Guide G-240W-F unit data sheet Indicator LED color and behavior LED behavior description USB Green solid At least one USB device is connected Green flashing Traffic activity on at least on USB device Off No USB device connected Green solid HSI WAN is connected: a) the device has an IP address assigned from IPCP, DHCP, or static, and no traffic has been detected; b) the session is dropped due to idle timeout but the PON link is still present.
G-240W-F unit data sheet 7368 ISAM ONT G-240W-F Product Guide Table 9 G-240W-F indoor ONT environmental specifications Temperature range and humidity Altitude Operating: 23°F to 113 F (-5°C to 45°C) ambient temperature Contact your Nokia technical support representative for more information 5% to 95% relative humidity, non-condensing Storage: -4°F to 158°F (-20°C to 70C) G-240W-F GEM ports and T-CONTs AF T 5.7 Table 10 lists the maximum number of supported T-CONTs and GEM ports. Table 10 5.
7368 ISAM ONT G-240W-F Product Guide Table 11 G-240W-F unit data sheet Package P ONTs ONTENET performance monitoring statistics LC RBO SCF MCF DT IMTE CSE AE IMRE FTL TBO SQE G-240W-F (1) EC ONTENET statistics FCSE ONT ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Note (1) AF T A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds Table 12 MCFRAMES DSDRPDFRMS USDRPDFRMS USFRAMES DSFRAMES USBYTES DSBYTES USMCFRAMES
G-240W-F unit data sheet RXFRAGS LOSTFRAGS ✓ ✓ ✓ ✓ BADGEMHDRS RXBLOCKS ✓ AF T G-240W-F (1) PONONTTC (aggregate) statistics TXFRAGS ONT Package P ONTs PONONTTC aggregate performance monitoring statistics TXBLOCKS Table 14 7368 ISAM ONT G-240W-F Product Guide Note (1) 5.
7368 ISAM ONT G-240W-F Product Guide Single-residence Wi-Fi ONT with Gigabit Ethernet and POTS and without RF video AF T Figure 18 G-240W-F unit data sheet R ONT SoC technology serves as the main hardware block for these ONTs; see Figure 19.
G-240W-F unit data sheet 7368 ISAM ONT G-240W-F Product Guide ONT SoC technology consists of five key elements: • GPON MAC • • • AF T • The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G.984.3 (GPON TC Layer) ITU specification. Ethernet MAC The SoC provides up to four GE MACs.
7368 ISAM ONT G-240W-F Product Guide G-240W-F unit data sheet • G.984.3 support for FEC in both upstream and downstream directions • G.984.3 support for multicast using a single GEM Port-ID for all video traffic • G984.4 and G.983.2 support for OMCI v1 and v2 interface for ONT management and provisioning • SIPv2 RFC 3261 signaling 5.10.
G-240W-F unit data sheet 5.11.1.1 7368 ISAM ONT G-240W-F Product Guide Wi-Fi physical features G-240W-F indoor ONTs have the following physical features that assist in providing Wi-Fi service: • WLAN button for enabling and disabling Wi-Fi service • two external multi-directional antennae • Wi-Fi Protected Setup (WPS) push button for enabling and disabling wireless protective services Wi-Fi standards and certifications AF T 5.11.1.
7368 ISAM ONT G-240W-F Product Guide G-240W-F unit data sheet Considerations and limitations The following voice features / GSIP parameters are configurable on a per-Client/ per-ONT basis (not per-Subscriber): • • • • • • Enable Caller ID and Enable Caller Name ID Digitmap and the associated Interdigit and Critical timers and Enter key parameters Warmline timer is enabled per subscriber, but the warmline timer value is configured per ONT and must have a lower value than the Permanent time Miscellaneous
7368 ISAM ONT G-240W-F Product Guide D R AF T G-240W-F unit data sheet 66 Edition 01 Issue: 01
7368 ISAM ONT G-240W-F Product Guide Install a G-240W-F indoor ONT 6 Install a G-240W-F indoor ONT 6.1 Purpose 6.2 General 6.3 Prerequisites 6.4 Recommended tools AF T 6.5 Safety information 6.6 Procedure 6.1 Purpose This chapter provides the steps to install a G-240W-F indoor ONT. 6.2 General The steps listed in this chapter describe mounting and cabling for G-240W-F indoor ONTs. Prerequisites R 6.3 You need the following items before beginning the installation: D • all required cables 6.
Install a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide • drill and drill bits • paper clip 6.5 Safety information Read the following safety information before installing the unit. AF T Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits.
7368 ISAM ONT G-240W-F Product Guide 6.6 Install a G-240W-F indoor ONT Procedure Use this procedure to install a G-240W-F indoor ONT. 1 Place the indoor ONT unit: a On the flat surface, such as a desk; go to step 3. AF T Note — The G-240W-F cannot be stacked with another ONT or with other equipment.
Install a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide If possible, mount the ONT on a wall stud ii Mark the wall with the location of the mounting holes. These holes should be the same distance apart as the distance between the centers of the keyholes on the ONT. iii Drill the two holes in the wall where the ONT will be mounted and then drive the mounting screws into the holes. The recommended length of mounting screw is 1.15 in. (3.8 cm). Do not drive the screw into the wall completely.
7368 ISAM ONT G-240W-F Product Guide G-240W-F ONT Reset, LED, WLAN, and WPS buttons and fiber optic connection (bottom and side view) AF T Figure 22 Install a G-240W-F indoor ONT D R The G-240W-F ONT features a fiber cover to protect the fiber optic cable and connection, as shown in Figure 23.
Install a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide 4 Connect the Ethernet cables to the RJ-45 ports; see Figure 21 for the location of the RJ-45 ports. Route the POTS cables directly to the RJ-11 ports as per local practices. R 5 G-240W-F indoor ONT with fiber cover open AF T Figure 23 The POTS port to the left is labeled 1 for Line 1 while the port on the right is labeled 2 for Line 2, as shown in Figure 21.
68 ISAM ONT G-240W-F Product Guide Install a G-240W-F indoor ONT Note — Fiber cable preparation varies depending on the type and size of the inside or outside plant fiber cable being spliced to the SC/APC (SC/UPC) fiber optic pigtail cable. 7 Install the power supply according to manufacturer specifications. Note — Observe the following: 8 9 10 11 Units must be powered by a Listed or CE approved and marked limited power source power supply with a minimum output rate of 12 V dc, 1.25 A.
7368 ISAM ONT G-240W-F Product Guide D R AF T Install a G-240W-F indoor ONT 74 Edition 01 Issue: 01
7368 ISAM ONT G-240W-F Product Guide Replace a G-240W-F indoor ONT 7 Replace a G-240W-F indoor ONT 7.1 Purpose 7.2 General 7.3 Prerequisites 7.4 Recommended tools AF T 7.5 Safety information 7.6 Procedure 7.1 Purpose This chapter provides the steps to replace G-240W-F indoor ONTs. 7.2 General The steps listed in this chapter describe mounting and cabling for G-240W-F indoor ONTs. Prerequisites R 7.3 You need the following items before beginning the installation: D • all required cables 7.
Replace a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide • optical power meter • drill and drill bits 7.5 Safety information Read the following safety information before replacing the unit. AF T Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits.
7368 ISAM ONT G-240W-F Product Guide 7.6 Replace a G-240W-F indoor ONT Procedure Use this procedure to replace a G-240W-F indoor ONT. 1 Deactivate the ONT services at the P-OLT. If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). Use the RTRV-ONT command to verify the ONT status and th associated services. Record the serial number or the SLID of the ONT displayed in the command output.
Replace a G-240W-F indoor ONT 3 Power down the unit by using the on/off power switch; see Figure 25 for the location of the power switch. G-240W-F indoor ONT connections (back view) 4 Disconnect the POTS, Ethernet, and power cables from the ONT; see Figure 25 for the connector locations on the G-240W-F indoor ONT. Disconnect the fiber optic cable; see Figure 26 for the location of the fiber optic port on the bottom of the ONT..
7368 ISAM ONT G-240W-F Product Guide G-240W-F indoor ONT fiber optic port (bottom view) AF T Figure 26 Replace a G-240W-F indoor ONT R Danger — Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Unplug the fiber optic cable with SC/APC connector from the fiber optic port on the bottom of the ONT; see Figure 26 for the location of the fiber optic port.
Replace a G-240W-F indoor ONT 8 7368 ISAM ONT G-240W-F Product Guide Connect the POTS cables directly to the RJ-11 ports as per local practices; see Figure 25 for the location of the RJ-11 ports. The RJ-11 port to the left is labeled 1 for Line 1 while the port on the right is labeled 2 for Line 2. If required, have approved service personnel who are trained to work with optic fiber clean the fiber optic connection.
7368 ISAM ONT G-240W-F Product Guide 16 Replace a G-240W-F indoor ONT If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide for more information. Note — A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager.
7368 ISAM ONT G-240W-F Product Guide D R AF T Replace a G-240W-F indoor ONT 82 Edition 01 Issue: 01
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT 8 Configure a G-240W-F indoor ONT 8.1 General 8.2 HGU mode GUI configuration 8.3 SFU mode GUI configuration AF T 8.4 Operator ID 8.1 General Please refer to the configuration information provided with your OLT for the software configuration procedure for a G-240W-F ONT. For HTTP configuration procedures, please refer to the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide. 8.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide The default gateway IP address is http://192.168.1.254. You can connect to this IP address using your web browser after connecting your PC to one of Ethernet ports of the ONT. The static IP address of your PC must be in the same subnet as the ONT. 2 Enter your username and password in the Log in window, as shown in Figure 27. The default user name is userAdmin. The default password is a random number, which is included in the ONT kit.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT • Optics module status • Voice information Procedure 7 Device information retrieval 1 Select Status > Device Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 28. Device Information window R AF T Figure 28 Table 16 describes the fields in the Device Information window.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide Field Description Device Running Time Amount of time the device has run since last reset in hours, minutes, and seconds (2 of 2) Click Refresh to update the displayed information. 3 STOP. This procedure is complete. Procedure 8 AF T 2 LAN status retrieval 1 Select Status > LAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 29.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT Field Description SSID Name Name of each SSID Wireless Encryption Status Encryption type used on the wireless connection Wireless Rx Packets Number of packets received on the wireless connection Wireless Tx Packets Number of packets transmitted on the wireless connection Wireless Rx Bytes Number of bytes received on the wireless connection Wireless Tx Bytes Number of bytes transmitted on the wireless connection Power Transm
Configure a G-240W-F indoor ONT Procedure 9 7368 ISAM ONT G-240W-F Product Guide WAN status retrieval 1 Select Status > WAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 30. WAN status window AF T Figure 30 Table 18 describes the fields in the WAN status window. WAN status parameters R Table 18 Description WAN connection list Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT Field Description Err Packets Number of errored packets on the WAN connection (2 of 2) Click Refresh to update the displayed information. 3 STOP. This procedure is complete. Procedure 10 AF T 2 WAN status IPv6 retrieval 1 Select Status > WAN Status IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 31.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide Description VLAN VLAN ID IPv6 Address IPv6 Address that identifies the device and its location IPv6 Prefix IPv6 prefix IPv6 Gateway IPv6 gateway address Primary DNS Primary Domain Name Server Second DNS Secondary Domain Name Server Pon Link Status Whether the PON link is up or down Tx Packets Number of packets transmitted on the WAN connection AF T Field Rx Packets Number of packets received on the WAN connection Tx
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT Table 20 describes the fields in the Home networking window. Table 20 Field Home networking parameters Description Local Interface Ethernet Table displays the number of Ethernet connections and their settings Wireless (2.4G) Table displays the number of wireless connections and their settings Wireless Settings (2.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide Table 21 describes the fields in the Optics module status window.
7368 ISAM ONT G-240W-F Product Guide Procedure 13 Configure a G-240W-F indoor ONT Voice information retrieval 1 Select Status > Voice Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 34. Voice Information window AF T Figure 34 Table 22 describes the fields in the Voice Information window.
Configure a G-240W-F indoor ONT 8.2.
7368 ISAM ONT G-240W-F Product Guide Procedure 14 Configure a G-240W-F indoor ONT LAN networking configuration 1 Select Network > LAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 35. LAN network window D R AF T Figure 35 Table 23 describes the fields in the LAN network window.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide Field Description DHCP enable Select this checkbox to enable DHCP DHCP Start IP Address Starting DHCP IP address DHCP End IP Address Ending DHCP IP address DHCP Lease Time DHCP lease time (in min) Bind MAC Address MAC address to associate to the LAN Bind IP Address IP address to associate to the bound MAC address (2 of 2) 3 4 5 6 Click Save. Enter the DHCP configuration information. Click Save.
7368 ISAM ONT G-240W-F Product Guide Procedure 15 Configure a G-240W-F indoor ONT LAN IPv6 networking configuration 1 Select Network > LAN_IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 36. LAN IPv6 network window AF T Figure 36 R Table 24 describes the fields in the LAN IPv6 network window. Table 24 LAN IPv6 network parameters Description DNS Server Choose a DNS server from the drop-down menu.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide Field Description Whether other info obtained through DHCP Select this checkbox to enable retrieval of other information through DHCP. Maximum interval for periodic RA messages Enter the maximum interval (in seconds) for periodic Router Advertisement messages. The interval range is from 4 to 1800. Minimum interval for periodic RA messages Enter the minimum interval (in seconds) for periodic Router Advertisement messages.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT Table 25 describes the fields in the WAN network window.
Configure a G-240W-F indoor ONT Procedure 17 7368 ISAM ONT G-240W-F Product Guide WiFi networking configuration 1 Select Network > WiFi from the top-level menu in the GPON Home Gateway window, as shown in Figure 38. WiFi network window R AF T Figure 38 D Table 26 describes the fields in the WiFi network window.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT Description Bandwidth Choose a channel from the drop-down menu or choose Auto to have the channel automatically assigned Channel Choose a bandwidth option from the drop-down menu Transmitting Power Choose the percentage transmitting power from the drop-down menu SSID Select Choose the SSID from the drop-down menu SSID Name Enter the SSID name Enable SSID Enable or disable SSID from this drop-down menu SSID Broadcast Enable
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide 4 Click Save. 5 STOP. This procedure is complete. Procedure 18 Wireless scheduling Select Network > Wireless Schedule from the top-level menu in the GPON Gateway window, as shown in Figure 39. AF T 1 Wireless Schedule window R Figure 39 Select the Schedule Function checkbox to turn the wireless signal off for the configured period. 3 Click the plus sign (+) to add a scheduling rule.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT 7 If desired, click the plus sign (+) to add more rules. 8 Click Save Changes. 9 STOP. This procedure is complete. Routing configuration 1 AF T Procedure 19 Select Network > Routing from the top-level menu in the GPON Home Gateway window, as shown in Figure 40. Routing network window D R Figure 40 Table 27 describes the fields in the Routing network window.
Configure a G-240W-F indoor ONT Table 27 3 Field Description Enable Routing Select this checkbox to enable routing Destination IP Address Enter the destination IP address Destination Netmask Enter the destination network mask Gateway Enter the gateway address IPv4 Interface Choose a WAN connection previously created in the WAN network window from the drop-down menu Forwarding Policy Choose a forwarding policy from the drop-down menu Enter the routing information. Click Add. STOP.
7368 ISAM ONT G-240W-F Product Guide Procedure 20 Configure a G-240W-F indoor ONT DNS configuration 1 Select Network > DNS from the top-level menu in the Home Gateway window, as shown in Figure 41. DNS network window R AF T Figure 41 Table 28 describes the fields in the DNS network window.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide 4 If required, associate an original domain with a new domain, click Add. 5 STOP. This procedure is complete. Procedure 21 TR-069 configuration Select Network > TR-069 from the top-level menu in the GPON Home Gateway window, as shown in Figure 42. AF T 1 TR-069 network window R Figure 42 Table 29 describes the fields in the TR-069 network window.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT 3 Click Save. 4 STOP. This procedure is complete. Procedure 22 GRE Tunnel configuration Select Network > GRE Tunnel from the top-level menu in the GPON Home Gateway window, as shown in Figure 43. AF T 1 GRE Tunnel window R Figure 43 Table 30 describes the fields in the GRE Tunnel window.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide Field Description Primary Remote End Enter an IP address or FQDN that is unique in the system. Secondary Remote End (optional) If the primary remote endpoint is down or unreachable, the secondary remote endpoint becomes active, if configured. The secondary remote endpoint remains active until it becomes unreachable, in which case the primary remote endpoint becomes active again. Revertive mode is not supported.
7368 ISAM ONT G-240W-F Product Guide QoS Config window (L2) R AF T Figure 44 Configure a G-240W-F indoor ONT D Figure 45 shows the window for configuring QoS L3 (Layer 3 packet sizes).
Configure a G-240W-F indoor ONT QoS Config window (L3) D R AF T Figure 45 7368 ISAM ONT G-240W-F Product Guide Table 31 describes the fields in the QoS Config window.
7368 ISAM ONT G-240W-F Product Guide Table 31 Configure a G-240W-F indoor ONT QoS Config parameters Field Description Type Choose a QoS service layer type from the drop-down menu L2 or L3. Source MAC Enter the source MAC. Select the Exclude checkbox to exclude the source MAC Choose an interface from the drop-down menu 802.1p Mark Enter the value for the 802.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide A classifier rule is used to assign actions to a group of packets based on a set of parameters. A classification rule must be created against a pre-defined classifier. Up to 16 policies can be created, with up to 8 classifiers and 32 classifier rules. 1 Select Network > US Classifier from the top-level menu in the GPON Home Gateway window, and select the Policy tab, as shown in Figure 46.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT 4 Click Save. 5 To delete a policy, click the Delete option for the applicable policy in the policy table. A policy can only be deleted if it is not associated with any classifier rules. 6 Select Network > US Classifier from the top-level menu in the GPON Home Gateway window, and select the Classifier tab, as shown in Figure 47. All classifiers are displayed in the classifier table in the window.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide Field Description Priority Select a priority level from 1 to 8. The lower the number, the higher the priority. No more than 1 classifier can be created with the same priority. (2 of 2) 7 Configure the US classifier. At least one field must be selected to create a classifier. A maximum of four fields may be selected to create a classifier; this includes the interface field. Click Save.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT Description Interface Select an interface from the drop-down menu, for example: None, LAN, 2.4G SSID, 5G SSID. Source MAC Enter a source MAC. Destination MAC Enter a destination MAC. Source IP Enter a source IP. Destination IP Enter a destination IP. Source Port Enter a source port. Destination Port Enter a destination port. IP Protocol type Enter a value between 0 and 254. AF T Field (2 of 2) 11 12 13 Click Save.
Configure a G-240W-F indoor ONT Procedure 25 7368 ISAM ONT G-240W-F Product Guide Firewall configuration 1 Select Security > Firewall from the top-level menu in the GPON Home Gateway window, as shown in Figure 49. Firewall window AF T Figure 49 Firewall security applies only to services provided by the ONT. Internet access from the LAN side is not affected by this firewall. Three security levels are available: Low, Medium, and High.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT Field Description Attack Protect (Protection against DoS or DDoS attacks) Choose enable or disable attack protect from the drop-down menu The default is disable (2 of 2) Configure the firewall. 3 Click Save. 4 STOP. This procedure is complete. Procedure 26 AF T 2 MAC filter configuration 1 Select Security > Mac Filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 50.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide Click Refresh to update the information. 3 Configure a MAC filter. 4 Click Add. 5 STOP. This procedure is complete. Procedure 27 AF T 2 IP filter configuration 1 Select Security > IP filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 51. IP filter window D R Figure 51 Table 37 describes the fields in the IP filter window.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT Field Description Internal Client Choose an internal client from the drop-down menu: • • Customer setting - uses the IP address input below IP - uses the connecting devices' IP to the ONT Local IP Address Local IP address Source Subnet Mask Source subnet mask Remote IP Address Remote IP address Destination Subnet Mask Destination subnet mask Protocol Choose an application protocol or all from the drop-down menu 2 3 4 Pro
Configure a G-240W-F indoor ONT Table 38 3 4 Procedure 29 Field Description Enable URL filter Select the checkbox to enable the URL filter URL filter type Select the checkbox for Exclude URL or Include URL URL Address Type the URL address Port Number Type the port number; the default is 80 Configure the URL Filter. Click Add Filter. STOP. This procedure is complete.
7368 ISAM ONT G-240W-F Product Guide Table 39 3 Parental control parameters Field Description Policy Name Enter a name for the parental control policy or choose a policy from the list MAC Address Enter the MAC address or choose a MAC address from the list IPv4 Address Enter the IPv4 address for the device or choose an IPv4 address from the list Days of the week Choose Every Day, or Individual Days and select the checkboxes for the days of the week for which the policy applies From/To Enter th
Configure a G-240W-F indoor ONT Procedure 30 7368 ISAM ONT G-240W-F Product Guide DMZ and ALG configuration 1 Select Security > DMZ and ALG from the top-level menu in the GPON Home Gateway window, as shown in Figure 54. DMZ and ALG window AF T Figure 54 Table 40 describes the fields in the DMZ and ALG window.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT 5 Click Save DMZ. 6 STOP. This procedure is complete. Procedure 31 Access control configuration This procedure describes how to configure the access control level (ACL). AF T Note 1 — ACL takes precedence over the firewall policy. Note 2 — The trusted network object will be shared for all WAN connections; it is not applied individually to a WAN connection.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide Field Description Trusted Network Enable Click to enable or disable ICMP, SSH, HTTP, TR-069 Select an access control level for each protocol: WAN side: Allow, Deny, or Trusted Network Only LAN side: Allow or Deny Source IP Start Enter a start IP address for the new subnet trusted network Source IP End Enter an end IP address for the new subnet trusted network (2 of 2) 3 4 5 6 Select a WAN connection from the drop-down menu.
7368 ISAM ONT G-240W-F Product Guide Procedure 32 Configure a G-240W-F indoor ONT Port forwarding configuration 1 Select Application > Port forwarding from the top-level menu in the GPON Home Gateway window, as shown in Figure 56. Port forwarding window AF T Figure 56 Table 42 describes the fields in the port forwarding window.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide 3 Click Add. 4 STOP. This procedure is complete. Procedure 33 Port triggering Select Application > Port Triggering from the top-level menu in the GPON Gateway window, as shown in Figure 57. AF T 1 Port Triggering window D R Figure 57 Table 43 describes the fields in the Port Triggering window.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT Field Description Open Protocol Choose the open port protocol from the drop-down menu: • • • Trigger Protocol TCP UDP TCP/UDP Choose the triggering port protocol from the drop-down menu: • • • TCP UDP TCP/UDP Select this checkbox to enable port triggering WAN Connection List Choose a WAN connection from the drop-down menu AF T Enable Triggering Note: only active devices are shown on this menu (2 of 2) 2 3 4 Click Add.
Configure a G-240W-F indoor ONT Table 44 3 4 Procedure 35 DDNS parameters Field Description WAN Connection List Choose a WAN connection from the drop-down menu Enable DDNS Select this checkbox to enable DDNS on the chosen WAN connection ISP Choose an ISP from the drop-down menu. Domain Name Domain name Username Username Password Password AF T 2 7368 ISAM ONT G-240W-F Product Guide Configure DDNS. Click Save. STOP. This procedure is complete.
7368 ISAM ONT G-240W-F Product Guide Table 45 3 4 Procedure 36 NTP parameters Field Description Enable NTP Service Select this checkbox to enable NTP service Current Time Enter the current local date and time First Time Server Choose a time server from the drop-down menu or choose Customer setting and enter the address of the time server. Second Time Server Choose a time server from the drop-down menu or choose Customer setting and enter the address of the time server.
Configure a G-240W-F indoor ONT Table 46 3 4 Procedure 37 USB storage parameters Field Description Enable FTP server Select this checkbox to enable using an FTP server for data storage Username Username for FTP server Password Password for FTP server Re-enter Password Password for FTP server Configure USB storage. AF T 2 7368 ISAM ONT G-240W-F Product Guide Click Save. STOP. This procedure is complete.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT Select the Enable Ushare checkbox to enable Ushare (the UPnP/DLNA media server). 5 Select the Enable DLNA checkbox to enable DLNA. 6 Click Save/Apply. 7 STOP. This procedure is complete. 8.2.
Configure a G-240W-F indoor ONT Procedure 38 7368 ISAM ONT G-240W-F Product Guide Password configuration 1 Select Maintain > Password from the top-level menu in the GPON Home Gateway window, as shown in Figure 62. Password window AF T Figure 62 Table 47 describes the fields in the password window.
7368 ISAM ONT G-240W-F Product Guide Procedure 39 Configure a G-240W-F indoor ONT LOID configuration 1 Select Maintain > LOID Config from the top-level menu in the GPON Home Gateway window, as shown in Figure 63. LOID Config window AF T Figure 63 Table 48 describes the fields in the LOID configuration window.
Configure a G-240W-F indoor ONT Procedure 40 7368 ISAM ONT G-240W-F Product Guide SLID configuration 1 Select Maintain > SLID Configuration from the top-level menu in the GPON Home Gateway window, as shown in Figure 64. SLID configuration window AF T Figure 64 Table 49 describes the fields in the SLID configuration window. Table 49 Description R Field SLID configuration parameters Displays current SLID Input new SLID Enter new SLID SLID Mode Choose a SLID mode from the drop-down menu.
7368 ISAM ONT G-240W-F Product Guide Procedure 41 Configure a G-240W-F indoor ONT Device management 1 Select Maintain > Device Management from the top-level menu in the GPON Home Gateway window, as shown in Figure 65. Device management window AF T Figure 65 Table 50 describes the fields in the Device management window.
Configure a G-240W-F indoor ONT Procedure 42 7368 ISAM ONT G-240W-F Product Guide Backup and restore 1 Select Maintain > Backup and Restore from the top-level menu in the GPON Home Gateway window, as shown in Figure 66. 2 Click Select File and choose the backup file. Click Import Config File to restore the ONT to the saved backup or click Export Config File to export the current ONT configuration to the backup file. R 3 Backup and Restore window AF T Figure 66 STOP. This procedure is complete.
7368 ISAM ONT G-240W-F Product Guide Procedure 43 Configure a G-240W-F indoor ONT Upgrade firmware 1 Select Maintain > Firmware Upgrade from the top-level menu in the GPON Home Gateway window, as shown in Figure 67. 2 3 Click Select File and choose the firmware file. Click Upgrade to upgrade the firmware. STOP. This procedure is complete.
Configure a G-240W-F indoor ONT Procedure 44 7368 ISAM ONT G-240W-F Product Guide Reboot ONT 1 Select Maintain > Reboot Device from the top-level menu in the GPON Home Gateway window, as shown in Figure 68. 2 Click Reboot to reboot the ONT. STOP. This procedure is complete.
7368 ISAM ONT G-240W-F Product Guide Procedure 45 Configure a G-240W-F indoor ONT Restore factory defaults 1 Select Maintain > Factory Default from the top-level menu in the GPON Home Gateway window, as shown in Figure 69. 2 Click Factory Default to reset the ONT to its factory default settings. STOP. This procedure is complete.
Configure a G-240W-F indoor ONT Procedure 46 7368 ISAM ONT G-240W-F Product Guide Diagnose WAN connections 1 Select Maintain > Diagnose from the top-level menu in the GPON Home Gateway window, as shown in Figure 70. Diagnose window R AF T Figure 70 Choose a WAN connection to diagnose from the drop-down menu. 3 Enter the IP address or domain name. 4 Select the test type: ping, traceroute, or both. D 2 140 5 Enter the number of ping attempts to perform (1 - 1000); the default is 4.
7368 ISAM ONT G-240W-F Product Guide 9 Click Cancel to cancel the test. 10 STOP. This procedure is complete. Procedure 47 View log files Select Maintain > Log from the top-level menu in the GPON Home Gateway window, as shown in Figure 71.
Configure a G-240W-F indoor ONT 7368 ISAM ONT G-240W-F Product Guide 4 The log file is displayed at the bottom of the window. 5 STOP. This procedure is complete. Procedure 48 Diagnose PPPoE connections Select Maintain > PPPoE Diagnostics from the top-level menu in the GPON Home Gateway window, as shown in Figure 72. AF T 1 PPPoE Diagnostics window R Figure 72 Click Check to view the results for the PPPoE diagnostics, as shown in Figure 73.
7368 ISAM ONT G-240W-F Product Guide PPPoE diagnostics results AF T Figure 73 Configure a G-240W-F indoor ONT Table 51 describes the fields on the PPPoE diagnostics results window.
Configure a G-240W-F indoor ONT Procedure 49 7368 ISAM ONT G-240W-F Product Guide Retrieve Residential Gateway (RG) troubleshooting counters 1 Select RG Troubleshooting Counters from the left menu in the GPON Home Gateway window. The RG Troubleshooting Counters window appears; see Figure 74. RG Troubleshooting Counters window AF T Figure 74 Table 52 describes the fields in the RG Troubleshooting Counters window.
7368 ISAM ONT G-240W-F Product Guide Configure a G-240W-F indoor ONT 3 Click Refresh to update the data. 4 STOP. This procedure is complete. 8.3 SFU mode GUI configuration AF T Use the procedures below to utilize the web-based GUI for the G-240W-F in SFU mode. This mode is preset at delivery. SFU customer premise devices are designed for single indoor residential applications.
Configure a G-240W-F indoor ONT Web login window AF T Figure 75 7368 ISAM ONT G-240W-F Product Guide Caution — Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID. Note — If you forget the current username and password, press the reset button for 10 s and the default values for the username and password will be recovered at startup. 3 STOP. This procedure is complete.
7368 ISAM ONT G-240W-F Product Guide Procedure 51 Device information retrieval 1 Select Status > Device Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 76. Device Information window AF T Figure 76 Configure a G-240W-F indoor ONT Table 53 describes the fields in the Device Information window.
Configure a G-240W-F indoor ONT 8.3.3 7368 ISAM ONT G-240W-F Product Guide Maintenance G-240W-F ONT also supports maintenance tasks, including: • password change • LOID configuration • SLID configuration Password configuration 1 Select Maintain > Password from the top-level menu in the GPON Home Gateway window, as shown in Figure 77. AF T Procedure 52 Figure 77 Password window Table 54 describes the fields in the password window.
7368 ISAM ONT G-240W-F Product Guide Procedure 53 Configure a G-240W-F indoor ONT LOID configuration 1 Select Maintain > LOID Config from the top-level menu in the GPON Home Gateway window, as shown in Figure 78. 2 3 4 Enter the LOID. Enter the password, if applicable. Click Save/Apply. STOP. This procedure is complete.
Configure a G-240W-F indoor ONT Procedure 54 7368 ISAM ONT G-240W-F Product Guide SLID configuration 1 Select Maintain > SLID Configuration from the top-level menu in the GPON Home Gateway window, as shown in Figure 79. SLID configuration window AF T Figure 79 Table 55 describes the fields in the SLID configuration window. Table 55 SLID configuration parameters Description Current SLID Displays current SLID Input new SLID Enter new SLID SLID Mode Choose a SLID mode from the drop-down menu.
7368 ISAM ONT G-240W-F Product Guide Procedure 55 Configure a G-240W-F indoor ONT Modifying the operator ID 1 Register the ONT with the OLT. 2 Check the original OPID. 3 Update the OntConfig.xml file by adding-the following content: AF T where: xxxx is the correct operator ID, for example ALCL for HGU mode, or XXXX for SFU mode. 4 5 Use a TFTP client tool to transfer the OntConfi.
7368 ISAM ONT G-240W-F Product Guide D R AF T Configure a G-240W-F indoor ONT 152 Edition 01 Issue: 01
7368 ISAM ONT G-240W-F Product Guide ONT configuration file over OMCI 9 ONT configuration file over OMCI 9.1 Purpose 9.2 Supported configuration file types 9.3 ONT configuration file over OMCI Purpose AF T 9.1 This procedure describes how to use configuration files over OMCI to configure ONTs.
ONT configuration file over OMCI Table 56 7368 ISAM ONT G-240W-F Product Guide Supported configuration files File Index Description Details Supported ONTs/DPU PRE ONT pre-configuration file The XML-based PRECONFIG file controls the working mechanics of the ONT for various services. The default behavior of different ONTs may vary based on the factory settings.
7368 ISAM ONT G-240W-F Product Guide ONT configuration file over OMCI File Index Description Details Supported ONTs/DPU GFT G.fast-related configuration file This text-based json script file controls the default behavior of the G.Fast ONT. HGU ONTs: G-240G-C,G-240W-F, G-240W-B, G-240W-C I-240W-A This file includes the provisioning parameters of the G.fast transports layer; it does not include VLAN or QoS provisioning.
ONT configuration file over OMCI Procedure 56 7368 ISAM ONT G-240W-F Product Guide Configuring an ONT using a configuration file via OMCI 1 Generate the TAR file to be uploaded to the OLT. Using the raw configuration file(s) provided by Nokia, generate the TAR file as follows: i On a Linux platform, rename the raw configuration file to adhere to the naming convention, as described in section 9.2. ii Tar the ABCXXXXVER raw configuration file: tar -cf ABCXXXXVER.
7368 ISAM ONT G-240W-F Product Guide ONT configuration file over OMCI FILENAME2 will be downloaded and FILENAME2 will be made passive. An ONT reboot is not required. iv If pland-cfgfileX=FILENAME3 and dnload-cfgfileX= FILENAME 4, the OLT reports an error because the filenames are not the same.
7368 ISAM ONT G-240W-F Product Guide D R AF T ONT configuration file over OMCI 158 Edition 01 Issue: 01
Customer document and product support Customer documentation AF T Customer Documentation Welcome Page Technical Support Customer Documentation Technical Support Documentation feedback D R Customer Documentation Feedback
FCC Rcgulations of the FCC Rul~. Opemtion is subject to 由efoUo飞，ving two conditioll!l: (1) This de\'ice cause h 3.n1由j interferenc e. andο) 由 is device mllst acc叩t 3. ny interference receiv时. includillg inte江 ference th3t may cause undesired operatioll 白lisd肝ice comp1i国 withpa此 15 ma川.10t This equ ipme.nr has b~.n tested and foun d 10 comply with the limits for é\ Cla岱 D digital dc'飞咀 e. purSllant to part 15 nC 山c Fr.r: Rul 出 Th<:."ωlim iL'i an; Ù出 I g商巳 J 1.0 prnviùe rCß~ (J nllhl c pr【 1 l.
