User's Manual
Table Of Contents
- G-240W-A Product Guide
- Preface
- ETSI ONT safety guidelines
- ETSI environmental and CRoHS guidelines
- ANSI ONT safety guidelines
- Contents
- List of figures
- List of tables
- 1 — G-240W-A unit data sheet
- 1.1 G-240W-A part numbers and identification
- 1.2 G-240W-A general description
- 1.3 G-240W-A software and installation feature support
- 1.4 G-240W-A interfaces and interface capacity
- 1.5 G-240W-A LEDs
- 1.6 G-240W-A detailed specifications
- 1.7 G-240W-A GEM ports and T-CONTs
- 1.8 G-240W-A performance monitoring statistics
- 1.9 G-240W-A functional blocks
- 1.10 G-240W-A standards compliance
- 1.11 G-240W-A special considerations
- 2 — Install a G-240W-A indoor ONT
- 3 — Replace a G-240W-A indoor ONT
- 4 — Configure a G-240W-A indoor ONT
- 4.1 General
- 4.2 HGU mode GUI configuration
- Login
- Procedure 4-1 Login to web-based GUI
- Device and connection status
- Procedure 4-2 Device information retrieval
- Procedure 4-3 LAN status retrieval
- Procedure 4-4 WAN status retrieval
- Procedure 4-5 WAN status IPv6 retrieval
- Procedure 4-6 Home networking information retrieval
- Procedure 4-7 Optics module status retrieval
- Procedure 4-8 Voice information retrieval
- Network configuration
- Procedure 4-9 LAN networking configuration
- Procedure 4-10 LAN IPv6 networking configuration
- Procedure 4-11 WAN networking configuration
- Procedure 4-12 WiFi networking configuration
- Procedure 4-13 Routing configuration
- Procedure 4-14 DNS configuration
- Procedure 4-15 TR-069 configuration
- Security configuration
- Procedure 4-16 Firewall configuration
- Procedure 4-17 MAC filter configuration
- Procedure 4-18 IP filter configuration
- Procedure 4-19 URL filter configuration
- Procedure 4-20 DMZ and ALG configuration
- Application configuration
- Procedure 4-21 Port forwarding configuration
- Procedure 4-22 DDNS configuration
- Procedure 4-23 NTP configuration
- Procedure 4-24 USB storage configuration
- Procedure 4-25 UPnP and DLNA configuration
- Maintenance
- Procedure 4-26 Password configuration
- Procedure 4-27 LOID configuration
- Procedure 4-28 SLID configuration
- Procedure 4-29 Device management
- Procedure 4-30 Backup and restore
- Procedure 4-31 Upgrade firmware
- Procedure 4-32 Reboot ONT
- Procedure 4-33 Restore factory defaults
- Procedure 4-34 Diagnose connections
- Procedure 4-35 View log files
- RG troubleshooting counters
- Procedure 4-36 Retrieve Residential Gateway (RG) troubleshooting counters
- 4.3 SFU mode GUI configuration
- 4.4 Operator ID
- 5 — ONT configuration file over OMCI
4 — Configure a G-240W-A indoor ONT
Alcatel-Lucent 7368 ISAM ONT 4-23
Edition 02
G-240W-A Product Guide
Procedure 4-17 MAC filter configuration
1 Select Security > Mac Filter from the top-level menu in the GPON Home Gateway
window, as shown in Figure 4-17.
Figure 4-17 MAC filter window
Table 4-16 describes the fields in the MAC filter window.
Table 4-16 MAC filter parameters
2 Configure a MAC filter.
3 Click Add.
4 STOP. This procedure is complete.
Field Description
Enable MAC filter Select this checkbox to enable the MAC filter
Mac Address MAC address
Mac Filter Mode Choose the MAC filter mode from this drop-down menu
R05.02.01 | October 2015 | 3FE-45360-AAAA-TCZZA | Edition 02