User's Manual
Table Of Contents
- G-240W-A Product Guide
- Preface
- ETSI ONT safety guidelines
- ETSI environmental and CRoHS guidelines
- ANSI ONT safety guidelines
- Contents
- List of figures
- List of tables
- 1 — G-240W-A unit data sheet
- 1.1 G-240W-A part numbers and identification
- 1.2 G-240W-A general description
- 1.3 G-240W-A software and installation feature support
- 1.4 G-240W-A interfaces and interface capacity
- 1.5 G-240W-A LEDs
- 1.6 G-240W-A detailed specifications
- 1.7 G-240W-A GEM ports and T-CONTs
- 1.8 G-240W-A performance monitoring statistics
- 1.9 G-240W-A functional blocks
- 1.10 G-240W-A standards compliance
- 1.11 G-240W-A special considerations
- 2 — Install a G-240W-A indoor ONT
- 3 — Replace a G-240W-A indoor ONT
- 4 — Configure a G-240W-A indoor ONT
- 4.1 General
- 4.2 HGU mode GUI configuration
- Login
- Procedure 4-1 Login to web-based GUI
- Device and connection status
- Procedure 4-2 Device information retrieval
- Procedure 4-3 LAN status retrieval
- Procedure 4-4 WAN status retrieval
- Procedure 4-5 WAN status IPv6 retrieval
- Procedure 4-6 Home networking information retrieval
- Procedure 4-7 Optics module status retrieval
- Procedure 4-8 Voice information retrieval
- Network configuration
- Procedure 4-9 LAN networking configuration
- Procedure 4-10 LAN IPv6 networking configuration
- Procedure 4-11 WAN networking configuration
- Procedure 4-12 WiFi networking configuration
- Procedure 4-13 Routing configuration
- Procedure 4-14 DNS configuration
- Procedure 4-15 TR-069 configuration
- Security configuration
- Procedure 4-16 Firewall configuration
- Procedure 4-17 MAC filter configuration
- Procedure 4-18 IP filter configuration
- Procedure 4-19 URL filter configuration
- Procedure 4-20 DMZ and ALG configuration
- Application configuration
- Procedure 4-21 Port forwarding configuration
- Procedure 4-22 DDNS configuration
- Procedure 4-23 NTP configuration
- Procedure 4-24 USB storage configuration
- Procedure 4-25 UPnP and DLNA configuration
- Maintenance
- Procedure 4-26 Password configuration
- Procedure 4-27 LOID configuration
- Procedure 4-28 SLID configuration
- Procedure 4-29 Device management
- Procedure 4-30 Backup and restore
- Procedure 4-31 Upgrade firmware
- Procedure 4-32 Reboot ONT
- Procedure 4-33 Restore factory defaults
- Procedure 4-34 Diagnose connections
- Procedure 4-35 View log files
- RG troubleshooting counters
- Procedure 4-36 Retrieve Residential Gateway (RG) troubleshooting counters
- 4.3 SFU mode GUI configuration
- 4.4 Operator ID
- 5 — ONT configuration file over OMCI
4 — Configure a G-240W-A indoor ONT
Alcatel-Lucent 7368 ISAM ONT 4-13
Edition 02
G-240W-A Product Guide
Table 4-8 LAN network parameters
2 Select the mode for each port.
3 Click Save.
4 Enter the DHCP configuration information.
5 Click Save.
6 Bind a MAC address to the LAN by entering the MAC and IP addresses and then
clicking Add. Repeat for all MAC addresses to be bound.
7 STOP. This procedure is complete.
Field Description
Port Mode:
All Port to L2 Mode
Select this checkbox to set all ports to L2 mode
Port Mode
Port 1 - 4
Drop-down port mode for each port: Route mode or bridge mode
IPv4 Address IP Address of the ONT
Subnet Mask Subnet mask of the ONT
DHCP enable Select this checkbox to enable DHCP
DHCP Start IP
Address
Starting DHCP IP address
DHCP End IP
Address
Ending DHCP IP address
DHCP Lease Time DHCP lease time (in min)
Bind MAC Address MAC address to associate to the LAN
Bind IP Address IP address to associate to the bound MAC address
R05.02.01 | October 2015 | 3FE-45360-AAAA-TCZZA | Edition 02