User's Manual
Table Of Contents
- G-240W-A Product Guide
- Preface
- ETSI ONT safety guidelines
- ETSI environmental and CRoHS guidelines
- ANSI ONT safety guidelines
- Contents
- List of figures
- List of tables
- 1 — G-240W-A unit data sheet
- 1.1 G-240W-A part numbers and identification
- 1.2 G-240W-A general description
- 1.3 G-240W-A software and installation feature support
- 1.4 G-240W-A interfaces and interface capacity
- 1.5 G-240W-A LEDs
- 1.6 G-240W-A detailed specifications
- 1.7 G-240W-A GEM ports and T-CONTs
- 1.8 G-240W-A performance monitoring statistics
- 1.9 G-240W-A functional blocks
- 1.10 G-240W-A standards compliance
- 1.11 G-240W-A special considerations
- 2 — Install a G-240W-A indoor ONT
- 3 — Replace a G-240W-A indoor ONT
- 4 — Configure a G-240W-A indoor ONT
- 4.1 General
- 4.2 HGU mode GUI configuration
- Login
- Procedure 4-1 Login to web-based GUI
- Device and connection status
- Procedure 4-2 Device information retrieval
- Procedure 4-3 LAN status retrieval
- Procedure 4-4 WAN status retrieval
- Procedure 4-5 WAN status IPv6 retrieval
- Procedure 4-6 Home networking information retrieval
- Procedure 4-7 Optics module status retrieval
- Procedure 4-8 Voice information retrieval
- Network configuration
- Procedure 4-9 LAN networking configuration
- Procedure 4-10 LAN IPv6 networking configuration
- Procedure 4-11 WAN networking configuration
- Procedure 4-12 WiFi networking configuration
- Procedure 4-13 Routing configuration
- Procedure 4-14 DNS configuration
- Procedure 4-15 TR-069 configuration
- Security configuration
- Procedure 4-16 Firewall configuration
- Procedure 4-17 MAC filter configuration
- Procedure 4-18 IP filter configuration
- Procedure 4-19 URL filter configuration
- Procedure 4-20 DMZ and ALG configuration
- Application configuration
- Procedure 4-21 Port forwarding configuration
- Procedure 4-22 DDNS configuration
- Procedure 4-23 NTP configuration
- Procedure 4-24 USB storage configuration
- Procedure 4-25 UPnP and DLNA configuration
- Maintenance
- Procedure 4-26 Password configuration
- Procedure 4-27 LOID configuration
- Procedure 4-28 SLID configuration
- Procedure 4-29 Device management
- Procedure 4-30 Backup and restore
- Procedure 4-31 Upgrade firmware
- Procedure 4-32 Reboot ONT
- Procedure 4-33 Restore factory defaults
- Procedure 4-34 Diagnose connections
- Procedure 4-35 View log files
- RG troubleshooting counters
- Procedure 4-36 Retrieve Residential Gateway (RG) troubleshooting counters
- 4.3 SFU mode GUI configuration
- 4.4 Operator ID
- 5 — ONT configuration file over OMCI
2 — Install a G-240W-A indoor ONT
2-6 Alcatel-Lucent 7368 ISAM ONT
Edition 02
G-240W-A Product Guide
The POTS port to the left is labeled 1 for Line 1 while the port on the right is
labeled 2 for Line 2, as shown in Figure 2-2.
6 Connect the fiber optic cable with SC/APC adapter into the SC/APC connector; see
Figure 2-2 for the location of the SC/APC connector.
7 Install the power supply according to manufacturer specifications.
8 Connect the power cable to the power connector.
9 Power up the ONT unit by using the power switch.
10 If used, enable the Wi-Fi service.
i Locate the WLAN button on the ONT; see Figure 2-3 for location of the WLAN
button.
ii Press the WLAN button to change the status of the Wi-Fi service.
11 Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368
Hardware and Cabling Installation Guide.
12 Activate and test the services; see the 7368 Hardware and Cabling Installation
Guide.
13 If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management,
and Troubleshooting Guide.
14 If necessary, reset the ONT.
i Locate the Reset button on a G-240W-A indoor ONT as shown in Figure 2-3.
ii Insert the end of a straightened paper clip or other narrow object into the
hole in the Reset button to reset the ONT.
15 STOP. This procedure is complete.
Danger — Fiber cables transmit invisible laser light. To avoid eye
damage or blindness, never look directly into fibers, connectors, or
adapters.
Warning — Be careful to maintain a bend radius of no less than 1.5 in.
(3.8 cm) when connecting the fiber optic cable. Too small of a bend
radius in the cable can result in damage to the optic fiber.
Note — Fiber cable preparation varies depending on the type and size
of the inside or outside plant fiber cable being spliced to the SC/APC
fiber optic pigtail cable.
Note — Observe the following:
• Units must be powered by a Listed or CE approved and marked
limited power source power supply with a minimum output rate of
12 V dc, 1.25 A.
R05.02.01 | October 2015 | 3FE-45360-AAAA-TCZZA | Edition 02