40389 23” x 19” POLYMER BENCH TOP CABINET ASSEMBLY INSTRUCTIONS DIVISION OF S&H INDUSTRIES 5200 Richmond Road Cleveland, OH 44146 Phone 216-831-0550 Toll Free 800-253-9726 Fax 216-831-9573 www.shindustries.com E-mail: www.service@shindustries.
40389 Assembly Instructions Page 2 ____________________________________________________________________ WARNING! Do not use an ALC Cabinet Blaster until you have read this manual and you understand its contents and warnings. These warnings are included for the health and safety of the operator and those in the immediate vicinity. Keep this manual for future reference.
40389 Assembly Instructions Page 3 POLYMER BENCHTOP CABINET – 40389 1 2 5 8 6 4 7 3 Key 1 2 3 4 5 6 7 8 Part No. 11646 11160 11161 10904 11644 10387 11601 10357 Description Louver vent 8-32 x 1/2” Screw 8-32 Nut Plug Snap fastener Lens 5/8” X 1” Foam Lens underlay Qty. 1 6 6 2 6 1 5ft 1 ADDITIONAL PARTS NOT SHOWN ON SCHEMATIC Part No. Description Qty.
0389 Assembly Instructions Page 4 POLYMER BENCHTOP CABINET SIPHON GUN REPLACEMENTS PARTS 40048 40051 11604 40345 40142 Part No. 11604 40345 40142 40050 40051 40052 40047 Description Blast gun (complete) Siphon Head Air Jet Washer Small Nozzle, 7 CFM Medium Nozzle, 15 CFM Large Nozzle, 20 CFM Small Air Jet, 7 CFM Part No.
40389 Assembly Instructions Page 5 ASSEMBLY INSTRUCTIONS 1. Take gloves and slip over circular flanges inside the cabinet. Secure gloves to flanges with glove clamps. If cabinet is supplied with 18” rubber gloves, help may be required to stretch gloves over the flanges. This is normal. 2. Attach abrasive blast hose to pick-up tube on inner portion of pick-up tube leaving 1/4” gap between hose end and outer tube. Lay pick-up tube in bottom of cabinet with hose end towards right rear of cabinet.
40389 Assembly Instructions Page 6 3. The plug in the right upper side of cabinet is for installation of a vacuum hose. We strongly recommend the use of a 1-2 H.P. shop vacuum or cabinet will leak the blast dust. 4. The 3” hole with louver vent in the upper left rear of the cabinet provides for proper venting of the cabinet during use. Never plug. AIR COMPRESSOR RECOMMENDATION: To permit efficient operation of your air compressor, follow these guidelines: 1.
40389 Assembly Instructions Page 7 6. Do not use sand. CABINET BLASTER SAFETY PROCEDURES CAUTION: READ THESE SAFETY PROCEDURES IN THEIR ENTIRETY – PARTS OF THE OPERATING INSTRUCTIONS ARE WITHIN THESE WARNINGS. These procedures are not intended to be exhaustive due to the many variables in the abrasive blasting field. Therefore, we INSIST that the hands, ears, mouth, nose and eyes be covered with appropriate safety protection at all times.
40389 Assembly Instructions Page 8 WARNING! The threads on the nozzle holder must be inspected each time the nozzle is secured to the holder. Check the threads for wear, and make sure nozzle holder securely grips the nozzle. The nozzle washer must also be inspected for wear. Worn nozzle washers cause thread erosion. A loose-fitting nozzle may eject from the holder under pressure and could cause severe injury. MOUNTING INSTRUCTIONS FOR THE OPTIONAL ECONOMY LIGHT KIT (P/N 40338) 1.
40389 Assembly Instructions Page 9 WARNING Follow all electrical and safety codes as well as the National Electrical Code (NEC) and OSHA Regulations. Part No.
1.
40389 Assembly Instructions Page 11 MAINTENANCE WARNING! Failure to observe the following before performing any maintenance could cause serious injury or death from the sudden release of compressed air: Disconnect power supply. Lockout and tagout the compressed air supply. Bleed the air supply line to the blast gun. Immediate replacement of worn components is required.
40389 Assembly Instructions Page 12 Coal Slag 40093 Coal Slag is used when paint and rust has to be removed from steel, such as car bodies, tanks or heavy machinery. Coal Slag is faster cutting, can be re-used, is moisture free, and will not pack or absorb moisture. (25 Lb. container) Steel Grit #40109 Steel grit is extremely fast cutting on rusty metal and hard to remove paint. Steel Grit is popular because it leaves a very smooth finish. It is also comparable in price to most other specialty abrasives.
40389 Assembly Instructions Page 13 TROUBLESHOOTING TIPS PROBLEM/CAUSE POSSIBLE SOLUTION Surging of blast flow: Air pressure too low Check pressure gauge on air compressor Excessive media consumption: Air pressure too low Check pressure gauge on air compressor Clogging and plugging of blast flow: Debris in media Media size too large Nozzle plugs Wet media Purge and screen Use smaller grit size Use larger nozzle and correct Dry media, drain water from air Moisture in abrasive media: Wet media Water i
40389 Assembly Instructions Page 14 Disclaimer of Warranties. S & H Industries, Inc. ("Seller") makes no warranties with respect to any goods delivered to Buyer or users except as specifically set forth within this manual. S & H INDUSTRIES, INC. MAKES NO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO ANY OF THE GOODS, AND S & H INDUSTRIES, INC. EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES AGAINST INFRINGEMENT. S & H INDUSTRIES, INC.
