ALAXALA AX3600S and AX2400S Quick Start Guide AX36S-Q001-50X Please read the entire manual, and then properly store it. • Before using the product, be sure to read and understand all the safety precautions. • Keep the manual somewhere where it can be readily accessed.
Relevant products This guide applies to the following: seven models in the AX2400S series (AX2430S-24T, AX2430S-24T2X, AX2430S-48T, AX2430S-48T2X, AX2430S-24TD, AX2430S-24T2XD, and AX2430S-48TD) and 15 models in the AX3600S series (AX3630S-24T, AX3630S-24T2X, AX3630S-24P, AX3630S-24TD, AX3630S-24T2XD, AX3630S-24S2XW, AX3630S-48TW, AX3630S-48T2XW, AX3640S-24T, AX3640S-24TW, AX3640S-24T2XW, AX3640S-24SW, AX3640S-24S2XW, AX3640S-48TW, and AX3640S-48T2XW).
AX-3630-24P (AX3630S-24P) AX-3630-24S2XW (AX3630S-24S2XW) AX-3630-48TW (AX3630S-48TW) AX-3630-48T2XW (AX3630S-48T2XW) AX-3640-24T (AX3640S-24T) AX-3640-24TW (AX3640S-24TW) AX-3640-24T2XW (AX3640S-24T2XW) AX-3640-24SW (AX3640S-24SW) AX-3640-24S2XW (AX3640S-24S2XW) AX-3640-48TW (AX3640S-48TW) AX-3640-48T2XW (AX3640S-48T2XW) AX-F2430-EPUA (EPU-A) AX-F2430-EPUB (EPU-B) Edition history Edition 1 (AX36S-Q001): December 2005 (1st edition) (obsolete) Edition 2 (AX36S-Q001-10): December 2
Preface Thank you for choosing an AX2400S series switch (ALAXALA compact gigabit layer 2 switch) or an AX3600S series switch (ALAXALA compact gigabit layer 3 switch). This guide describes the procedures from unpacking to the basic configuration of an AX2400S or AX3600S series switch. In addition, the guide also explains how to use the manuals for the AX2400S and AX3600S series switches to ensure stable operation of the switch.
Preface II
Contents Preface I Safety Information 1 2 Safe-1 Preparations 1 1.1 Organization of the AX2400S and AX3600 series manuals 2 1.2 Viewing the AX2400S and AX3600S series manuals 4 1.3 Verifying supplied components 5 1.4 Preparing a setup terminal and cables 6 Installing a Switch 9 2.1 Installing a switch 3 4 10 2.1.1 Installing a switch only 10 2.1.2 Using an EPU 26 2.2 Other preparations 45 Operations Required for Initial Installation 47 3.
Table of Contents ii
Safety Information Using AX2400S and AX3600S series switches correctly and safely z This guide provides important information for ensuring safe use of AX2400S and AX3600S series switches. Please read this guide completely before using your switch. z Keep this guide handy after finishing it, so that it is available for later reference. z Operate your switch according to the instructions and procedures provided in this guide. z Heed all warnings and cautions regarding the switch in this guide.
Safety Information If anything seems wrong, immediately turn off the power. z If smoke or an unusual smell is coming from the switch, or if liquid is spilled into the switch or a foreign object falls into the switch, immediately turn off power to the switch as described below. Continuing operation could result in a fire or electric shock.
Safety Information Do not place anything on the switch z Do not place any metallic object such as a small pin or a paper clip or any container with a liquid, such as a vase or a flower pot, on the switch. Liquid or metallic objects falling into the switch could result in a fire or electric shock.
Safety Information Use the switch only with the indicated power supply setting. z Do not use the switch at any voltage other than the indicated voltage. Doing so could result in a fire or electric shock. The current capacity of a distribution panel must be greater than that of the operating current fed to the circuit breaker. z The current capacity of a distribution panel must be greater than that of the operating current fed to the circuit breaker.
Safety Information Observe the specified stripping length of the sheath for the power cable. z When using a DC -48 V power cable for a redundant power model, adjust the stripping length of the sheath for the power cable (the switch end) to 8 to 10 mm. If the striping length is too short, connection might fail or the cable might become disconnected. Conversely, if the length is too long, the core will be exposed, risking electric shock.
Safety Information Do not use the switch with the protection cap removed. z Do not remove the protection cap except when attaching a cable. Using a switch with no protection cap could result in a fire or electric shock. Note that the following label is affixed near the standby power connector due to the high output power of EPU-B. Handle power cables carefully. z Do not place anything heavy on a power cable. Do not pull, bend, or modify a cable.
Safety Information Do not place the switch in a place where it is unstable. z If placing the switch on a desk, lay it on its side on a workbench capable of withstanding the weight of the switch. Do not place the switch somwhere that might be unstable. If, for example, you place the switch on a shaky table or a tilted surface, the switch might fall and possibly injure someone. z When installing a switch in a rack, make sure the switch in the rack is stably positioned.
Safety Information When moving a switch, do not hold the handle of the power supply, fan unit, or power supply module. z When moving a redundant power model, do not hold the handle of the power supply or the fan unit. The handle might come off, resulting in injury. In addition, the power supply or the fan unit might become damaged, resulting in a fire or electric shock. z When moving an EPU, do not hold the handle of the power supply module.
Safety Information When moving a switch z Before moving a switch, you must turn it off and unplug all cables. Failure to do so might cause the switch or cable to become damaged, resulting in a fire or electric shock. z If you must stack multiple switches during transport, use appropriate packaging. Failure to do so might cause the switch to become deformed or damaged, resulting in a fire or electric shock. Do not handle the power cable roughly.
Safety Information When turning off the power, stop the supply of all power to the switch. z If power is supplied to an AC model and an AC (PoE) model from an EPU, switch power cannot be turned off by setting just the power switch of the switch to OFF. To turn off the switch, set the power switch of both the switch and the power module to OFF.
Safety Information Do not install the switch in a dusty or humid location. z Do not install the switch in a dusty or humid location. Doing so could result in a fire or electric shock. z Condensation might form on the surfaces and the inside of the switch if it is moved from a cold location to a warm location. Using the switch in this condition could result in a fire or electric shock.
Safety Information Do not step on a switch, lean against it, or place anything on it. z Do not step on a switch, lean against it, or place anything on it. Doing so might damage the switch. Furthermore, the switch might fall or lose its balance, resulting in injury. z Do not place anything that weighs more than 5 kg on a switch. Doing so might damage the switch, cause the switch to fall or cause a loss of balance, resulting in injury. Do not touch the inside of the switch with your hands.
Safety Information Do not place a switch in a high-temperature location. z Do not place a switch in direct sunlight or near a heater or other heat-generating apparatus. Doing so could adversely affect parts of the switch. Do not use a TV or a radio near a switch. z Placing a switch near a TV or a radio could affect both devices. If you hear noise on the TV or radio, do the following: • Place the switch as far away as possible from the TV or radio. • Adjust the orientation of the TV or radio antenna.
Safety Information Turn off the power before installing or removing a power supply module. z Before installing or removing a power supply module, turn off its power. Installing or removing the module with the power supply module turned on causes a (switch) failure. The following label is affixed to the EPU. Turn off the power of the power supply modules before turning on the main power switch of an EPU. z Before turning on the main power switch of an EPU, turn off the installed power supply modules.
Safety Information Do not affix any labels on a transceiver. z A label indicating that the transceiver is a standard product from Alaxala or another manufacturer is affixed to the transceiver. Note that this label is affixed where it does not affect heat dissipation of the transceiver and mechanisms that prevent the transceiver from falling. Affixing a label in such locations could cause the transceiver to fall or could damage a switch. Do not turn off the switch while the ST1 LED is blinking green.
Safety Information Safety-16
1 Preparations This chapter describes the preparations necessary for using AX2400S and AX3600S series switches. It also describes the manual organization for AX2400S and AX3600S series switches, where this guide is in that manual organization, and where the manuals can be viewed from. 1.1 Organization of the AX2400S and AX3600 series manuals 1.2 Viewing the AX2400S and AX3600S series manuals 1.3 Verifying supplied components 1.
1. Preparations 1.1 Organization of the AX2400S and AX3600 series manuals The figures below provide an overview of the AX2400S and AX3600S series manuals. This Quick Start Guide explains only the operations from unpacking the switch to setting it up for basic operation. Note that this guide provides only a minimum amount of information. To take advantage of the wealth of functions provided by AX2400S and AX3600S series switches, see the following manuals.
1.
1. Preparations 1.2 Viewing the AX2400S and AX3600S series manuals The AX2400S and AX3600S series manuals are available on the ALAXALA website at the following address: http://www.alaxala.
1. Preparations 1.3 Verifying supplied components Use the packing list to verify that all components and accessories are present. A packing list is also provided for optional components, such as power supplies, fan units, EPUs, power supply modules, and transceivers. If you purchased an optional component, check that packing list as well.
1. Preparations 1.4 Preparing a setup terminal and cables To set up an AX2400S or 3600S series switch, prepare the following in addition to the AX2400S and AX3600S series switch, components, and accessories. z Setup terminal Prepare a personal computer or a workstation that supports the specifications in the following table. Table 1-1 Setup terminal specifications Item Specification Communication port RS-232C port Communication software Tera Term Pro (Version 2.
1. Preparations z 200 V AC power cable When an AC model and a redundant power model are used at 200 V AC, a 200 V AC power cable is required. For details about preparing a 200 V AC power cable, see the AX3600S/AX2400S Hardware Instruction Manual. z DC power cable When a redundant power model is used at -48 V DC, a DC power cable is required. For details about preparing a DC power cable, see the AX3600S/AX2400S Hardware Instruction Manual.
1.
2 Installing a Switch This chapter describes the procedure for installing a switch into a 19-inch cabinet rack and turning on the power. 2.1 Installing a switch 2.
2. Installing a Switch 2.1 Installing a switch This section describes the procedure for installing an AX2400S or AX3600S series switch into a 19-inch cabinet rack and turning on the power. 2.1.1 Installing a switch only [Step 1] Installing a switch Use the following procedure to install a switch into a 19-inch cabinet rack. When moving a redundant power model, do not hold the handle of a power supply or a fan unit.
2. Installing a Switch When installing the switch in a rack, if you cannot maintain a 100-mm space (for cables) in front of the switch, slide the brackets 50 mm toward you and attach them as shown in the following figure. Figure 2-2 Attaching the rack mounting brackets by sliding them 50 mm forward (1) Rack mounting bracket (L) (2) Rack mounting bracket (R) (3) Screws (M3 x 6 for each bracket, 12 screws in all) Use the supplied screws when you attach the rack mounting brackets to the switch.
2. Installing a Switch 2. Install the switch in the rack. Figure 2-3 Installing a switch in the rack (1) Screws (M5 x 4) (2) 19-inch cabinet rack Before installing a switch in a rack, make sure that the switch is stable. Performing this operation under unstable conditions could result in injury if the switch falls off the rack. When installing a switch in a rack, use the supplied M5 screws. [Step 2] Connecting a power cable to the switch Connect a power cable to the switch.
2. Installing a Switch z AC power cable (AC model and AC (PoE) model) Connect the supplied power cable to the AC power connector on the rear of the switch. Figure 2-4 Connecting the AC power cable (for an AC model and an AC (PoE) model) (1) Standby power connector (with a protection cap) (2) Cable clamp (3) AC power cable (4) AC power connector When using this switch at 100 V AC, use the supplied power cable. Failure to do so could result in fire or electric shock.
2. Installing a Switch For the specified power cables, see the AX3600S/AX2400S Hardware Instruction Manual. z AC power cable (redundant power model) Connect a power cable to the power supplies for the switch (connect the supplied power cable to the AC power connector on the rear of the switch). Figure 2-5 Connecting the AC power cable (redundant power model) (1) Cable clamp (2) AC power cable (3) AC power connector When using the switch at 100 VAC, use the supplied power cable.
2. Installing a Switch For details about the specified power cables, see the AX3600S/AX2400S Hardware Instruction Manual. z DC power cable (DC model) Use the supplied power cable. Using another cable could result in a fire or electric shock. In addition, do not use the supplied cable with other devices. Doing so could result in a fire or electric shock. Connecting or disconnecting the DC power cable to the power supply must be performed by a trained technician or maintenance personnel.
2. Installing a Switch The ground terminal must be connected for proper grounding. Failure to do so could result in electric shock or failures due to electrical noise. 2. Connect the supplied power cable to DC power connector 1 on the rear of the switch (push the connector until you hear a click). Figure 2-7 Connecting the DC power cable (1) DC power connector 2 (with the protection cap) (2) DC power cable (3) DC power connector 1 Do not remove the protection cap except for when connecting a cable.
2. Installing a Switch z DC power cable (redundant power model) Use the specified DC power cable. Using another cable could result in a fire or electric shock. Connecting and disconnecting a DC power cable must be performed by a trained technician or maintenance personnel. Before connecting or disconnecting a DC power cable, turn off the power. Failure to do so could result in a fire or electric shock. For details about specified power cables, see the AX3600S/AX2400S Hardware Instruction Manual. 1.
2. Installing a Switch Ground cables are supplied with no cable end treatment on the power supply side. Apply appropriate terminal treatment such as connecting terminals appropriate for the power supply. For details about ground cables, see the AX3600S/AX2400S Hardware Instruction Manual. 2. *Remove the connector cable from the power supply unit (pull the connector while holding the right and left levers). Figure 2-9 Removing the cable connector (1) Cable connector (2) Power supply unit 3.
2. Installing a Switch 4. *Insert the power cable, and return the buttons to their original positions (the power cable is clamped). Figure 2-11 Connecting the DC power cable -2 (1) DC power cable (2) -48 V (3) 0 V Adjust the stripping length of the sheath for the DC power cable (on the switch end) to 8 to 10 mm. If the stripping length is too short, connections might fail or the cable might become disconnected. Conversely, if the length is too long, the core will be exposed, risking electric shock.
2. Installing a Switch 5. *Attach the cable connector to the power supply unit (push the connector until you hear a click). Figure 2-12 Attaching the cable connector (1) Cable connector (2) DC power connector (3) Power supply unit Before attaching or removing the cable connector, turn off the power supply unit. To make the power supply redundant, perform steps 2* to 5* to connect a power cable to the other power supply unit.
2. Installing a Switch [Step 3] Installing a dummy memory card Insert a dummy memory card (dummy card hereafter) until you hear a click, and then gently remove your fingers (install the dummy card with the notch facing left). Figure 2-13 Installing a dummy card (1) Dummy card (2) Memory card slot When installing a dummy card, do not force the card or pinch it with your fingers. Doing so might damage the connector.
2. Installing a Switch [Step 4] Installing a transceiver Install the SFP or XFP transceiver if you have purchased one. Insert the SFP transceiver with the lever raised as shown in the following figure until you hear a click. Figure 2-14 Installing a transceiver (upper port) (1) SFP (2) SFP slot The above figure shows an example for installing a transceiver in an SFP slot for an AX3630S-24S2XW, AX3640S-24SW, or AX3640S-24S2XW.
2. Installing a Switch [Step 5] Connecting the setup terminal Connect the setup terminal to the switch. 1. Connect the setup terminal to the CONSOLE port of the switch. Use an RS-232C cross cable for the connection. Figure 2-16 Connecting the setup terminal (1) Setup terminal (2) RS-232C cross cable (3) CONSOLE port After the setup terminal is connected to the port, tighten the screws. Also make sure the terminal is securely connected. For details about RS-232C cross cables, see 1.
2. Installing a Switch [Step 7] Turning on the power Set the AX3600S/AX2400S power switch to ON.
2. Installing a Switch When redundant power supplies are installed for a redundant power model, if only one of the power switches is set to ON, a power supply error might be detected (and the ST1 LED will blink red). Setting both power switches to ON removes the error state. [Step 8] Checking the LEDs If the ST1 LED on the front panel of the switch turns green, the switch is running. For details about the process for starting a switch, see 2.2 Other preparations.
2. Installing a Switch 2.1.2 Using an EPU [Step 1] Installing the switch Install an AX2400S or AX3600S series switch in a 19-inch cabinet rack. To install a switch on a desk, see the AX3600S/AX2400S Hardware Instruction Manual. The supplied fixing brackets are designed for M5 screws. Prepare a rack that accommodates M5 screws. 1. Attach the rack mounting brackets to the switch.
2. Installing a Switch Figure 2-22 Attaching rack mounting brackets to the switch (brackets moved 50 mm forward) (1) Rack mounting bracket (L) (2) Rack mounting bracket (R) (3) Screws (M3 x 6, 12 screws in all) Use the supplied screws when attaching the rack mounting brackets to the switch.
2. Installing a Switch 2. Install the switch in the rack. Figure 2-23 Installing a switch in a rack (1) Screws (M5 x 4) (2) 19 inch cabinet rack Before installing a switch in a rack, make sure the switch is stable. Performing this operation under unstable conditions could result in injury if the switch falls off the rack. When installing a switch in a rack, use the supplied M5 screws.
2. Installing a Switch [Step 2] Installing the EPU and power supply module Install the EPU in the 19 inch cabinet rack. If you plan to supply standby power to multiple switches from a single EPU, install the power supply module in the EPU. Do not hold the handle of the power supply module when moving an EPU. Doing so might cause the handle to come off and the EPU to fall, possibly resulting in injury. Also, the EPU or the power supply unit might become damaged, resulting in a fire or electric shock.
2. Installing a Switch Figure 2-25 Attaching the rack mounting brackets to the EPU (brackets moved 50 mm forward) (1) Rack mounting bracket (L) (2) Rack mounting bracket (R) (3) Screws (M3 x 6 for each bracket, 12 screws in all) Use the supplied screws when attaching the rack mounting brackets to the EPU.
2. Installing a Switch 2. Install the EPU in the rack. Figure 2-26 Installing the EPU in the rack (1) Screws (M5 x 4) (2) 19-inch cabinet rack Before installing an EPU in a rack, make sure the device is stable. Performing this operation under unstable conditions could result in injury if the EPU falls off the rack. When installing an EPU in a rack, use the supplied M5 screws.
2. Installing a Switch 3. Install the power supply module in the EPU (Push the power supply module until you hear a click). Before installing or removing the power supply module, set the power switch of the module to OFF. The following figure shows an example of installing the power supply module in and removing it from slot 2 of EPU-A. Perform the same procedure for other EPU-A and EPU-B slots.
2. Installing a Switch [Step 3] Connecting a power cable to a switch Connect the supplied power cable to the AC power connector on the rear of the switch. Figure 2-28 Connecting the AC power cable (1) Standby power connector (with a protection cap) (2) Cable clamp (3) AC power cable (4) AC power connector When using this switch at 100 V AC, use the supplied power cable. Using another cable could result in a fire or electric shock. In addition, do not use the supplied cable for another switch.
2. Installing a Switch When a switch is installed in a rack, use the cable holder supplied with the rack to fix the power cable in order to prevent stress on the cable base. For details about the specifications for the specified power cable, see the AX3600S/ AX2400S Hardware Instruction Manual. [Step 4] Connecting a power cable to the EPU This section describes how to connect the power cable to the EPU. Connect the AC power cable and the standby power cable, which supplies standby power to the switch.
2. Installing a Switch 1. Connect the AC power cable to an EPU. Figure 2-29 Connecting the AC power cable (1) Cable clamp (2) AC power cable (3) AC power connector (4) Main power switch Use the supplied power cable. Using another cable could result in a fire or electric shock. In addition, do not use the supplied power cable with another switch. Doing so could result in a fire or electric shock. Before connecting or disconnecting a power cable, set the main power switch of the EPU to OFF.
2. Installing a Switch 2. Connect the standby power cable to the EPU (press the cable until you hear a click). Figure 2-30 Connecting the standby power cable (on the EPU side) (1) Connector for supplying standby power (with a protection cap) (2) Connector for supplying standby power (3) Cable for supplying standby power Do not remove the protection cap except to connect a cable. Using the AX3600S/AX2400S without a protection cap could result in a fire or electric shock.
2. Installing a Switch 3. Connect the standby power cable to the AX3600S/AX2400S (press the cable until you hear a click). Figure 2-31 Connecting the standby power cable (on the switch) (1) Standby power cable (2) Standby power connector (with a protection cap) Connect the standby power cable after removing the protection cap. Make sure you keep the removed protection cap in a safe place.
2. Installing a Switch [Step 5] Installing a dummy memory card Insert a dummy memory card (dummy card hereafter) until you hear a click, and then gently remove your fingers (install the dummy card with the notch facing left). Figure 2-32 Installing a dummy card (1) Dummy card (2) Memory card slot When installing a dummy card, do not force the card or pinch it with your fingers. Doing so might damage the connector.
2. Installing a Switch [Step 6] Installing a transceiver Install an SFP or XFP transceiver if you have purchased one. Insert the SFP transceiver with the lever raised as shown in the following figure until you hear a click. Figure 2-33 Installing a transceiver (upper port) (1) SFP (2) SFP slot The above figure shows an example for installing a transceiver in an SFP slot for an AX3630S-24S2XW, AX3640S-24SW, or AX3640S-24S2XW.
2. Installing a Switch [Step 7] Connecting the setup terminal Connect the setup terminal to the switch. 1. Connect the setup terminal to the CONSOLE port of the AX3600S/AX2400S. Use an RS-232C cross cable for the connection. Figure 2-35 Connecting the setup terminal (1) Setup terminal (2) RS-232C cross cable (3) CONSOLE port After the setup terminal is connected to the port, tighten the screws. Also make sure the terminal is firmly connected. For details about RS-232C cross cables, see 1.
2. Installing a Switch [Step 8] Connecting an interface cable Connect the interface cable to the interface port. For a PoE connection, if you disconnect and then re-connect a UTP cable within two seconds of connecting the cable, the power class of the equipment on the power-receiving side might not be recognized correctly. When removing and re-connecting the cable, be sure to wait for at least two seconds. [Step 9] Turning on the power Set the power switch of the AX3600S/AX2400S to ON.
2. Installing a Switch 2. Set the power switch of the power supply module to ON.
2. Installing a Switch [Step 11] Checking the LEDs Check the LEDs of the AX3600S/AX2400S, EPU, and power supply module. 1. Check the ST1 LED on the front panel of the switch. When the ST1 LED turns green, the switch has started. Figure 2-40 Checking the LEDs For details about the process until the switch is started, see 2.2 Other preparations. If the red ST1 LED is blinking or on, a switch failure has occurred.
2. Installing a Switch 3. Make sure the LED of the power supply module turns green (check the DC-OK LED for EPU-AM, and check the AC-OK and DC-OK LEDs for EPU-BM). Figure 2-42 Checking the LEDs (for EPU-AM) Figure 2-43 Checking the LEDs (for EPU-BM) If the LEDs (the DC-OK LED for EPU-AM, and the AC-OK and DC-OK LEDs for EPU-BM) do not turn green, there might not be any power being supplied to the power supply module.
2. Installing a Switch 2.2 Other preparations z Checking the progress of switch startup The following describes the process from turning on the power until the switch starts. 1. After the power is turned on, the ST1 LED on the front panel of the switch turns green, and the startup process starts. 2. When the switch starts, the ST1 LED turns green.
2.
3 Operations Required for Initial Installation This chapter describes the procedures required for initial system startup, such as setting the time and the administrator mode password, and adding and deleting user IDs. 3.1 Overview of the command input modes 3.2 Overview of initial setup operations 3.3 Login 3.4 Setting the administrator mode password 3.5 Adding a user ID and deleting the operator user ID 3.
3. Operations Required for Initial Installation 3.1 Overview of the command input modes The command line interface (CLI) for this switch has three command input modes: user mode, administrator mode, and configuration command mode. To set up or change a switch configuration, or view the switch status, you must switch to the appropriate command input mode and enter a configuration or operation command. The following table describes the characteristics of each command input mode.
3. Operations Required for Initial Installation z Configuration command mode In administrator mode, entering the configure command puts you in configuration command mode. In this mode, you can use the configuration command to set and change the configuration of the switch. Configuration command mode has a hierarchical structure. (config)# in the above table is called global configuration mode. Below this prompt, input modes are categorized according to the type of commands available.
3. Operations Required for Initial Installation 3.2 Overview of initial setup operations This section provides an overview of the operations required when a switch is initially installed. For detailed operations, see the subsequent sections. The operations below are the minimum requirements when a switch is installed. For operations after the initial operations, see the manuals listed in 4.1 Detailed operations of AX2400S and AX3600S series switches. (1) Login Log in to the switch.
3. Operations Required for Initial Installation 3.3 Login When the switch is started, the login prompt appears. Enter the user ID at the prompt to log in to the switch. Although the screen shots provided in the following explanations might differ depending on the software version, the basic operations are the same.
3. Operations Required for Initial Installation 3.4 Setting the administrator mode password Specify the password for administrator mode. We recommend that you use six or more characters for the password. If a password consisting of fewer than six characters is entered, an error is displayed. A password of fewer than six characters can still be used by entering it again. Passwords cannot exceed 128 characters.
3. Operations Required for Initial Installation 3.5 Adding a user ID and deleting the operator user ID [Step 1] Creating a user ID and setting the login password Create a new user ID and set the login password. The following example shows how to create the user ID newuser and set a password for it. We recommend that you use six or more characters for the password. If a password consisting of fewer than six characters is entered, an error is displayed.
3. Operations Required for Initial Installation 3.6 Setting the time Set the time zone and the time. The following example shows the procedure for setting the time zone as Japan and the time to December 1st, 2005, at 15:30. If the configuration is changed, the ! symbol appears before the prompt. This symbol disappears when the configuration is saved. After the time has been set for the switch, the correct time is maintained for 10 days after the switch has been turned off.
4 Other Operations This chapter describes the manuals you need to reference to specify advanced settings for the switch, check the operating status, and troubleshoot any problem that might occur. 4.1 Detailed operations of AX2400S and AX3600S series switches 4.
4. Other Operations 4.1 Detailed operations of AX2400S and AX3600S series switches This guide describes only the minimum operations required to initially install a switch. You can use a wealth of functions provided by your switch by specifying operations management and configuration settings. After reading this guide, specify the operations management and configuration settings appropriate for your system.
4. Other Operations 4.2 Troubleshooting See the relevant manual in the table if a problem with the switch occurs.
4.
