Specifications
show port
161
#1: inact is cleared in the following conditions:
The port is restored by execution of the
activate command.
Due to the BPDU guard functionality of the Spanning Tree Protocol
The storm control functionality
Detection of a unidirectional link failure by the UDLD functionality
The L2 loop detection functionality.(The automatic restoration functionality can be
also used for recovery.)
The standby link functionality of link aggregation makes the standby port the active
port.
#2: If
full(auto) is displayed for 100BASE-FX, the configuration setting is invalid. Check
the setting.
Example 2
Figure 13-7 Example of listing protocol information for ports
> show port protocol
Date 2009/10/29 11:33:37 UTC
Port Counts: 26
Port Name Type VLAN STP QoS Filter MACTbl Ext.
0/1 fastether0/1 Trunk 8 0 0(0) 0(0) 1 - - - -
0/2 fastether0/2 Access 1 0 0(0) 0(0) 0 - - - -
0/3 fastether0/3 Access 1 0 0(0) 0(0) 0 - - - -
0/4 fastether0/4 Access 1 0 0(0) 0(0) 0 - - - -
0/5 fastether0/5 Access 1 0 0(0) 0(0) 1 - - L -
0/6 fastether0/6 Access 1 0 0(0) 0(0) 0 - - - -
0/7 fastether0/7 Access 1 0 0(0) 0(0) 0 - - - -
0/8 fastether0/8 Access 1 0 0(0) 0(0) 0 - - - -
0/9 fastether0/9 Access 1 0 0(0) 0(0) 0 - - - -
0/10 fastether0/10 Access 1 0 0(0) 0(0) 0 - - - -
0/11 fastether0/11 MAC 6 0 0(0) 0(0) 0 - - - -
0/12 fastether0/12 Access 0 0 0(0) 0(0) 0 - - - -
0/13 fastether0/13 Access 1 0 0(0) 0(0) 0 - - - -
0/14 fastether0/14 Access 1 0 0(0) 0(0) 0 - - - -
0/15 fastether0/15 Access 1 0 0(0) 0(0) 0 - - - -
0/16 fastether0/16 Access 1 0 0(0) 0(0) 0 - - - -
0/17 fastether0/17 Trunk 10 0 0(0) 0(0) 3 - - - A
0/18 fastether0/18 Trunk 10 0 0(0) 0(0) 3 - - - A
0/19 fastether0/19 Trunk 10 0 0(0) 0(0) 3 - - - A
0/20 fastether0/20 Trunk 10 0 0(0) 0(0) 3 - - - A
0/21 fastether0/21 Trunk 10 0 0(0) 0(0) 3 - - L A
0/22 fastether0/22 Trunk 10 0 0(0) 0(0) 3 - - L A
0/23 fastether0/23 Trunk 10 0 0(0) 0(0) 3 - - L A
0/24 fastether0/24 Trunk 10 0 0(0) 0(0) 3 - - L A
0/25 gigaether0/25 Trunk 10 0 0(0) 0(0) 9 - - - A
0/26 gigaether0/26 Access 1 0 0(0) 0(0) 0 - - - -
I: Isolation setting S: Storm control setting
L: LLDP setting A: Ring Protocol setting
>