Wireless Trilogy 345 Bayview Avenue Amityville, New York 11701 For Sales and Repairs 1-800-ALA-LOCK For Technical Service 1-800-645-9440 (Note: Technical Service is for locksmiths and alarm professionals only) Publicly traded on NASDAQ Symbol: NSSC Networx PL6100 Programming Instructions WI1843 09/10 © ALARM LOCK 2010 PL6100 HID HID CORPORATION HID PROXCARD® PROXKEY® KEYFOB AL-PRE PROXCARD® READER / ENROLLER DL-WINDOWS PROGRAMMING SOFTWARE PL Wireless Trilogy Series Network Access Control System
PL6100 WIRELESS LOCK THE ALARM LOCK W IRELESS TRILOGY PL-SERIES STAND-ALONE ACCESS CONTROL SYSTEM IS A STATE-OFTHE-ART MICROPROCESSOR-BASED COMPUTER NETWORK PROGRAMMABLE PROXIMITY SECURITY LOCK. PL6100 The DL6100 is designed to allow all features to be programmed through its radio link from a DL-Windows-equipped computer. In addition, Audit Log Data may be transmitted through the radio link back to the DL-Windows computer.
Wireless PL Series Lock Features Audit Trail • 40,000 Event Capacity • Entries Logged with Time and Date • Critical Programming Events Logged • Uploadable using Alarm Lock's DL-Windows software Lock Features • Metal Key Override for all cylindrical locks • Non-Volatile (Fixed) Memory • Real-Time Clock (with automatic Daylight Saving Time adjust) • Programmable Relay (via DL-Windows only) • Visual and Audible Feedback • Battery Status Monitor Scheduling (Using DL-Windows) • 500 Scheduled Events • Automated
Supported Products AL-IM SERIES WI-FI Gateway Module Each lock contains a radio that transmits and receives--via a private wireless signal--to an intermediate device called a Gateway module. In turn, this Interface Module is connected (either wirelessly or wired) to a computer network such as a LAN or corporate Intranet. A Windows PC connected to this network can control and program all locks by the use of the DL-Window software (see OI237).
Lock Design Overview Why Use "Software" inside a Lock? With ordinary door locks, the need to make physical copies of metal keys and distributing them can be a huge organizational and financial task -- and what will you do if someone causes a security breach by losing their key? The answer lies in the advantage of SOFTWARE. Software (also called "firmware") is not "hard" or "fixed" like hardware is. Software is "soft" -- flexible and changeable to your needs.
Terminology Used in this Manual What is a Lock Program? (Also called Lock Programming). A Lock Program contains the instructions that a lock uses to perform its various functions. Use DL-Windows (defined below) to create a Lock Program on your computer, and then transfer and store the Lock Program in the circuitry contained inside the lock itself. The Lock Program is essentially a computer database file that maintains feature settings, proximity card data, schedules, audit trails, etc.
Terminology Used in this Manual (cont'd) given proximity cards, it is convenient to think of each "location" as a "User", although technically the User Number is only a location within the Lock Program. It is easier to say "User 519" rather than "The User in possession of the proximity card that is assigned to the User Location number 519". Note: Where a User is located in this list--their User Location--is a commonly used description of their User Number.
Wiring See the installation instructions for additional information. Batteries: Use only four 1.5 volt Alkaline size-C batteries or an Alarm Lock pre-wired battery pack assembly. External Power: Red / Black wires - External 7.5 VDC Power Source must be used for operation without batteries. Remote Input: White / White wires - Wire a normally open contact to wires (white and white). Momentarily close to allow PL6100 lock to unlock. NOTE: Remote Input is enabled from the factory.
Erase All Programming Restore the "out of box" factory condition. 1. At the back of the lock, remove the lock housing screw and remove the cover. 2. Take out battery pack and remove battery power by disconnecting the battery pack plug. 3. With battery power disconnected, short the two white wires (Remote Input wires) together for 10 seconds to ensure discharge of all capacitors. After 10 seconds, remove the short. 4. Plug in the (provided) male shunt connector into the yellow wire female connector. 5.
DL-Windows Programmable Functions "Programmable Features" Screen - Options tab Lockout Time in Seconds The duration of time the lock refuses to recognize ANY proximity card presentations after the maximum number of invalid entry attempts (with an invalid proximity card) has been reached (valid entries are 1-60 seconds). Lock Responds to Emergency Commands See the Wireless Network Setup & DL-Windows Configuration Instructions, OI352.
DL-Windows Programmable Functions "Programmable Features" Screen - Relay Functions tab Scheduled (Group 1 Activated) Activates relay if the PL6100 has been programmed for "Scheduled Relay Activation (Group 1 Initiated)" and a member of Group 1 has presented their proximity card within the required window. Locked by Schedule Activates relay if the PL6100 has been locked by a programmed schedule. Unlocked by Schedule Activates relay if the PL6100 has been unlocked by a programmed schedule.
"Programmable Features" Screen - Remote tab Forced Unlock Follows Remote Input When Remote Input switch is closed, regardless of the current state of the lock, the lock will unlock for the duration of the Remote Input switch closure. Important: If this feature is enabled, power to the lock MUST be provided from an external power supply. The "Remote Input" wires are two white wires located inside the rear housing. When these two white Remote Input wires are momentarily shorted, the PL6100 unlocks.
User Card Record Sheet NAME OF DOOR: EMBOSSED NUMBER ON CARD Page # ______ DEPARTMENT: USER NAME (LAST, FIRST) DATE ACTIVATED COMMENTS 13
Glossary ACCESS = Entry into a restricted area. AUDIT TRAIL = A date/time stamped log of previous lock events. BURGLARY CONTROL PANEL = Provides local alarm and remote communication to request security for burglary/break-in. CLOCK • GROUP 1 PUTS UNIT IN PASSAGE = A proximity card (previously assigned to Group 1) presented to the lock during a pre-defined schedule unlocks the lock. Programmed only through DLWindows. • REAL TIME CLOCK = An accurate built-in clock that allows date/time stamping of events.
NOTES 15
ALARM LOCK LIMITED WARRANTY ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants its products to be free from manufacturing defects in materials and workmanship for 24 months following the date of manufacture. ALARM LOCK will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
