345 Bayview Avenue Amityville, New York 11701 For Sales and Repairs 1-800-ALA-LOCK For Technical Service 1-800-645-9440 Publicly traded on NASDAQ Symbol: NSSC INSTALLATION TEMPLATE DL1200 DL1300 PDL1300 4070 © ALARM LOCK 2006 WI1513 2/06
Trilogy 345 Bayview Avenue Amityville, New York 11701 For Sales and Repairs 1-800-ALA-LOCK For Technical Service 1-800-645-9440 (Note: Technical Service is for security professionals only) Publicly traded on NASDAQ Symbol: NSSC DL1200 Programming Instructions © ALARM LOCK 2012 OI310B 12/12 CONGRATULATIONS! Your new DL1200 Alarm Lock Trilogy electronic digital lock is a manually programmable narrow stile entry trim for Adams Rite® 4710, 4730 and 4900 deadlatch locks, and 1850, 1950, 4070, MS1850S and MS1
Wiring Wiring: See the Installation Instructions for more information. Batteries: Use only two '123' Type Lithium batteries (Duracell P/N CR17345). Quick Start First Time Start Up 1. Unpack the lock from its factory packaging. 2. Connect the battery pack. 3. Listen for 3 beeps. The lock is now ready to accept programming. Note: Failure to follow this exact procedure can result in erratic lock behavior.
Quick Start (cont’d) Enter a Manager Code Manager Codes are located at locations 00, 10, 20, 30, 40, 50, 60, 70, 80, and 90 (see grid on page 4). Note: New Manager Codes MUST use the same number of digits as the (new) Master Code. Enter as follows. 1. Press the (new) Master Code. 2. Press ; [press a Manager location i.e. 00, 10, 20, 30, 40, 50, 60, 70, 80, or 90] ;. 3. Press a new Manager Code using the same number of digits as the (new) Master Code. A 6-beep acknowledgement (with a red LED) will sound.
Manager & User Location Worksheet The DL1200 lock provides three "security levels": Master (can perform ALL functions), Manager (can perform SOME programming functions plus entry), and Basic User (entry only). In total, there are 104 "locations" inside the DL1200 lock: one Master Code, 10 Manager and 90 User Access Codes, and three "one-time entry" Service Codes. Where the Access Code is located will determine its security level.
Manager & User Location Example User Access Codes allow access only; Manager Codes allow more: Manager Codes have the ability to program and delete User Access Codes within that Manager's Bank (column). The DL1200 lock can hold up to 10 Manager Codes, one for each Bank (locations (00), (10), (20), (30), (40), (50), (60), (70), (80), (90)), and are all found at the top row of the grid below. Note: Only the Master Code can add or delete a Manager Code.
Programming Worksheet: Functions Directions: The Factory Master Code (1-2-3-4-5) must first be reprogrammed as a new Master Code before any other programming can take place. All new Access Codes must have the same number of digits as the new Master Code. Choose new Access Codes and write them in spaces provided (in pencil) before programming the lock. 6 beeps will usually be heard after an acceptable entry.
Programming Functions Change Existing Master Code* ; 1 ; For new locks, follow the "Quick Start" on page 2. [ __ __ __ __ __ ] ;1; Old (or "Factory") Master Code [ __ __ __ __ __ ] ; [ __ __ __ __ __ ] New Master Code* Confirm New Master Code* Add/Change Manager Codes ; [ __ ] 0 ; Follow the "Quick Start" on page 3. Note: You can also add/change the Manager Code in location 00 by entering the Master Code, ; 2 ; then the new Manager Code.
Programming Functions (cont'd) Enable/Disable All Disable All: If Master Code is used, disables all 100 User\Manager Codes and clears all 3 Service Codes. If a Manager Code is used, disables all Users (even across multiple Banks) under that Manager. Disable Users Only: If Master Code is used, disables all 90 Users and clears all 3 Service Codes, while Managers remain active. If a Manager Code is used, disables all Users (even across multiple banks) under that Manager.
Programming Functions (cont'd) Add/Delete Service Codes Service Codes are one-time-only Codes; once entered into the keypad, it is deleted. Use the same Code up to 3 times by programming all three Service Codes with the same Code. Note: Service Codes are lost if power is removed. To delete a single Service Code, press ;, enter Service Code number (301, 302 or 303), then press ; :.
Programming Functions (cont'd) Disable/Enable Users in Bank Enter Bank number (0-9) to Enable/Disable all Users in Bank. Entering a disabled Code will result in an accented five beep error tone (indicating the User Access Code is valid but disabled).
Battery Replacement When a valid code is entered and the batteries are weak, the red & green LED's will light and the sounder will sound for 4 seconds. The DL1200 uses two '123' Type Lithium batteries (Duracell P/N CR17345). The lock will function with weak batteries; however be sure to replace them as soon as possible.
Alarm Lock Limited Warranty ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants its products to be free from manufacturing defects in materials and workmanship for 24 months following the date of manufacture. ALARM LOCK will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
