About This Manual Thank you for choosing the Akuvox IT88 series indoor monitor. This manual is intended for the administrators who need to properly configure the indoor monitor. This manual applies to the 88.30.110.302 version, and it provides all the configurations for the functions and features of the IT88 series door phone. Please visit the Akuvox forum or consult technical support for any new information or the latest firmware.
Related Documentation You are advised to refer to the related documents for more technical information via the link below: https://knowledge.akuvox.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IT88 Series Administrator Guide 1.Product Overview IT88 series is an Android SIP-based with a smooth touch-screen indoor monitor. It can be connected with the Akuvox door phone for audio/video communication, unlocking, and monitoring.Residents can communicate with visitors via audio/video call, and it supports unlocking the door remotely. It is more convenient and safer for residents to check the visitor’s identity through its video preview function.
IT88 Series Administrator Guide 3.Introduction to Configuration Menu Status: This section gives you basic information such as product information, Network Information, and account information, etc. Account: This section concerns SIP account, SIP server, proxy server, transport protocol type, audio&video codec, DTMF, session timer, etc. Network: This section mainly deals with DHCP&Static IP setting, RTP port setting, and device deployment, etc.
IT88 Series Administrator Guide access control between smartphones and Akuvox intercoms. All configurations in the device will be issued automatically from the cloud. If users decide to use Akuvox SmartPlus, please contact Akuvox technical support, and they will help you configure the related settings before using them. SDMC mode: SDMC (SIP Device Management Controller) is a simple and comprehensive software for building management.
IT88 Series Administrator Guide 4.Access the Device Akuvox indoor monitor system settings can be either accessed on the device directly or on the device web interface. 4.1. Device Start-up Network Selection Akuvox indoor monitor system settings can be either accessed on the device directly or on the device's web interface. After the device boots up initially, you are required to select the network connection for the device.
IT88 Series Administrator Guide can configure different types of functions as needed. To access the device basic setting by pressing Setting icon. To checking the basic information like MAC, firmware and ect. 4.2.2.Accessing Device Advanced Setting To access the advanced setting, press Setting then press Advanced Settings icon. Press password 123456 to enter the advanced setting. 4.3.
IT88 Series Administrator Guide Note: You can also obtain the device IP address using the Akuvox IP scanner to log in the device web interface. Please refer to the URL below for the IP scanner application: https://knowledge.akuvox.com/docs/akuvox-ip-scanner Note: Google Chrome browser is strongly recommended. The Initial user name and password are “admin” and please be case-sensitive to the user names and passwords entered. AKUVOX SMART INTERCOM www.akuvox.
IT88 Series Administrator Guide 5.Language and Time Setting 5.1. Language Setting When you first set up the device, you might need to set the language to your need or you can do it later if needed. Language setting can be configured on the device that allows you to select or change the language for screen display to your preference. To configure the language display on the device Settings > Time&Language screen. 5.2.
IT88 Series Administrator Guide Automatic Date: automatic Date is switched on by default, which allows the date& time to be automatically set up and synchronized with the default time zone and the NTP server (Network Time Protocol). You can also set it up manually by checking off the square box and then enter the time and date you want and press the Save tab to save the setting. Time Zone: select the specific time zone depending on where the device is used. The default time zone is GMT+0.00.
IT88 Series Administrator Guide the time zone setting in your device. Parameter Set-up: NTP Server: enter the NTP server you obtained in the NTP server field. 6.Screen Display Configuration IT88 series indoor monitor allow you to enjoy a variety of screen displays to enrich your visual and operational experience through the customized setting to your preference. AKUVOX SMART INTERCOM www.akuvox.
IT88 Series Administrator Guide 6.1. Screen Display setting on the Device You can configure a variety of features of the screen display in terms of brightness, screen saver and font size, etc. To do this configuration on device Setting > Display screen. Parameter set-up: Brightness: press on the brightness setting and move the yellow dots to adjust the screen brightness. The default brightness is “145”. Sleep Time: set the timing for the device screen to be turned off.
IT88 Series Administrator Guide 1 SDMC Pictures Display pictures from SDMC as the screen saver. 2 Local Pictures Display picture uploaded to the indoor monitor as the screen saver. 3 SDMC+Local Pictures Display pictures from SDMC and the indoor monitor in rotation as the screen saver. 4 SDMC Videos Display videos from SDMC as the screen saver.
IT88 Series Administrator Guide 6.2. Screen Display Setting on the Web Interface IT88 series indoor monitor allows you to enjoy a variety of screen displays to enrich your visual and operational experience through the customized setting to your preference. 6.2.1.Upload Screen Saver You can upload screen saver pictures separately or in batch to the device and to the device web Device > Display Setting > Screen Saver Setting interface for a public purpose or for a greater visual experience.
IT88 Series Administrator Guide Display Setting > Wall Paper interface in order to achieve the visual effect and experience you need for your personalized screen background display. Note: The pictures uploaded should be in JPG, JPEG, PNG format with 2M maximum. 6.2.3.Upload Device Booting Image You can upload the booting image to be displayed during the device’s booting process if needed on device web Device > Display Setting> Boot Logo interface. Note: The pictures uploaded should be in .
IT88 Series Administrator Guide Parameter Set-up: Type: click to select among sixteen icon options: “DND”, “Message”,” Contact”, “Call”, “Display”, ”System info”, “Setting”, “Sound”, “Arming”, “SOS”, “Browser”, ”Motion Detection”, “Custom APK”, “Relays”, “Unlock”, “N/A” is selected, the icon display in the corresponding area will disappear. Value: select the value if you select the icon type “Custom APK” and “Browser”.
IT88 Series Administrator Guide 7.Sound and Volume Configuration Akuvox IT88 series indoor monitors provide you with various types of ringtone and volume configuration ranging from Mic volume, Ring volume, Talk volume, Tone volume and Media volume. You can configure them on the device directly or on the web interface. 7.1. Volume Configuration 7.1.1. Configure Volume on the Device To set up the volumes on the device Setting > Sound screen.
IT88 Series Administrator Guide 7.1.1.1. Configure Volume on the Web Interface You can configure the volumes and tones and customize your doorbell sound and alarm ringtone to your preference on device web Device > Audio interface. Note: Doorbell sound files and Alarm Ringtone files to be uploaded must be .WAV or MP3 format. No limitation for the file size. 8.Phone Book Configuration AKUVOX SMART INTERCOM www.akuvox.
IT88 Series Administrator Guide 8.1. Phone Book Configuration on the Device You can configure the contacts list in terms of adding and modifying contact groups or contacts on the device Contacts > Local Contacts directly. 8.1.1.Add contact Parameter Set-up: Account1: select which account to use to dial out, Account 1 or Account 2. New Contact Name: enter the name to save. Number: enter the IP or SIP number to save. CameraUrl: enter the RTSP URL for video preview.
IT88 Series Administrator Guide You can check and edit the exited contacts in the phonebook list. Choose one and click Edit key to modify. 8.1.3.Block List setting on the device Choose which contact on the contact list you want to be added to the blocklist. Note: You can delete contacts regardless of whether it is on the All Contacts screen or the Blocklist screen. 8.2. Phone Book Configuration on the Web Interface 8.2.1.
IT88 Series Administrator Guide Parameter set-up: Name: enter the contact name to be saved. Number: enter the contact number (SIP or IP number ) to be saved. Group: select Default or Blocklist group. Dial Account: select Account1 or Account2. 8.2.2. Contact Management You can search, display, edit, and delete the contacts in your contacts list on web Contacts > Local Contacts > Local Contacts List interface.
IT88 Series Administrator Guide Note: If you want to remove the contact from the blocklist on the web interface, you can change the group to the “Default" when editing the contact. 8.2.4. Contacts Import and Export on the Web Interface When the contact becomes so many that you can not afford to manage each contact one by one manually, you can import and export the contacts in batch on the device web Contacts > Local Contacts > Local Contacts List interface.
IT88 Series Administrator Guide 9.Network Setting & Other Connection 9.1. Device Network Configuration You can check for the door phone’s network connection info and configure the default DHCP mode (Dynamic Host Configuration Protocol) and static IP connection for the device either on the device or on the device web interface. 9.1.1.Configuring Device Network Connection on the Device To check and configure the network connection on the device Settings > Advance Settings > Network screen.
IT88 Series Administrator Guide Static IP: select the static IP mode by checking off the DHCP check box. When static IP mode is selected, then the IP address, subnet mask, default gateway, and DNS servers address have to be manually configured according to your actual network environment. IP Address: set up the IP Address if the static IP mode is selected. Subnet Mask: set up the subnet Mask according to your actual network environment.
IT88 Series Administrator Guide To check the network on the web Status > Network information interface. To check and configure network connection on the device web Network > Basic > LAN Port interface. Parameter Set-up: DHCP: select the DHCP mode by checking the DHCP box. DHCP mode is the default network connection. If the DHCP mode is selected, then the indoor monitor will be assigned by the DHCP server with IP address, subnet mask, default gateway, and DNS servers address automatically.
IT88 Series Administrator Guide Akuvox IT88 series indoor monitors should be deployed before they can be properly configured in the network environment in terms of their location, operation mode, address and extension numbers as opposed to other devices for device control and the convenience of the management. To deploy the device in the network on web Network > Advanced > Connect Setting interface.
IT88 Series Administrator Guide Advanced > NAT interface. Parameter Set-up: RPort: check the RPort when the SIP server is in WAN (Wide Area Network). 9.4. Device Bluetooth Setting 9.4.1.Device Bluetooth Pairing After IT88 series indoor monitors turn on the Bluetooth on the device Settings > Bluetooth screen, it can be paired with other device via Bluetooth. 9.4.2.Device Bluetooth Data Transmission To transfer data via Bluetooth by pressing Pair new device.
IT88 Series Administrator Guide 9.5. Device Wi-Fi Setting In addition to wired connection, the device also supports Wi-Fi connection. To set the Wi-Fi on device Settings > Advance Settings > WIFI screen. 10. Intercom Call Configuration AKUVOX SMART INTERCOM www.akuvox.
IT88 Series Administrator Guide 10.1.IP call & IP Call Configuration IP calls and SIP calls can be made directly on the intercom device by entering the IP number on the device. And you can also disable the direct IP call if you allow no IP call to be made on the device. 10.1.1. Make IP Calls To make a directly IP call on the device Call screen. Enter the IP address you which to call on the soft keyboard, press Audio or Video tab to call out.
IT88 Series Administrator Guide the check box to terminate the function. Direct IP Call Port: the direct IP Call Port is "5060" by default with the port range from 1-65535. And you enter any values within the range other than the 5060, you are required to check if the value entered is consistent with the corresponding value on the device you wish to establish a data transmission with. 10.2.
IT88 Series Administrator Guide "5060" by default. The parameter settings for SIP account registration can be configured on the Account setting screen and they can also be configured on the device web Account > Basic > SIP Account interface. Parameter setup: Status: check to see if the SIP account is registered or not. Account: select Account1 or Account2. Account Enabled: check to active the registered SIP account.
IT88 Series Administrator Guide SIP server between intercom devices. To perform the SIP account setting on the Web Account > Basic > SIP Server interface. Parameter Set-up: Server Address: enter the Server’s IP address number or its URL. Sip Server Port: set up SIP server port for data transmission. Registration Period: set up SIP account registration time pan. SIP re-registration will start automatically if the account registration fails during the registration time span.
IT88 Series Administrator Guide Preferred Outbound Proxy Server: enter the SIP address of the outbound proxy server. Preferred Outbound Proxy Port: enter the Port number for establish call session via the outbound proxy server. Alternate Outbound Proxy Server: set up Backup Server IP for the backup outbound proxy server. Alternate Outbound Proxy Port: enter the Port number for establish call session via the backup outbound proxy server. 10.6.
IT88 Series Administrator Guide For the device network data transmission purpose, device needs to be set up with a range of RTP port (Real-time Transport Protocol) for establishing an exclusive range of data transmission in the network. To set up device local RTP on web Network > Advanced > Local RTP interface. Parameter set-up: Starting RTP Port: enter the Port value in order to establish the start point for the exclusive data transmission range.
IT88 Series Administrator Guide TLS: select “TLS” for Secured and Reliable transport layer protocol. DNS-SRV: select “DNS-SRV” to obtain DNS record for specifying the location of services. And SRV not only records the server address but also the server port. Moreover, SRV can also be used to configure the priority and the weight of the server address. 10.9.Call Setting IT88 will auto answer all incoming calls if call auto-answer is enabled and receive live stream if live stream is enabled. 10.9.1.
IT88 Series Administrator Guide automatically. Answer Mode: set up the video or audio mode you preferred for answering the call automatically. Indoor Auto Answer: turn on the Auto Answer function for call from other indoor monitors by ticking the check box . 10.9.2. Auto-answer Allow List setting Auto answered can only be applicable to the SIP or IP numbers that are already added in the auto-answer white-list of your indoor monitor.
IT88 Series Administrator Guide 10.9.3. Live Stream Setting Receive Live Stream on the indoor monitor allows you to see the video image (one way video stream) from the calling device such as a door phone whether or not you answered the call in audio or video mode, while the video image from your indoor monitor will not be sent to the calling devices in order to protect your privacy. To do the configuration on web Device > Call Feature >Audio Call Settings interface.
IT88 Series Administrator Guide If you want to see the image at the door station before answering the incoming call, you can enable the intercom preview function on web Device > Intercom > Intercom interface. Parameter Set-up: Intercom Active: tick the check box to enabled or disabled intercom function. Intercom Mute: tick the check box to enable mute the voice from the callee side and vice versa. Intercom Preview: tick the check box to enable the incoming call preview function.
IT88 Series Administrator Guide Call Number: to setup 3 SOS numbers. Once users press SOS key on the home page (SOS display key shall be set on the web manually), indoor monitors will call out the number in order. Call Timeout: setup the timeout for each number. Once users call out, if the other side will not answer within the timeout, indoor monitors will continue to call the next number. Loop Times: to setup the call loop times. 10.12.
IT88 Series Administrator Guide Parameter Set-up: Account: to choose which account shall implement call forwarding feature. Always Forward: to enable always forwarding function; all incoming calls will be automatically forward to a specific number. Busy Forward: to enable busy forwarding function; incoming calls will be forwarded to a specific number if phone is busy.
IT88 Series Administrator Guide Busy Transfer: to enable busy forwarding function; incoming calls will be forwarded to a specific number if phone is busy. No Answer Transfer: to enable no answer forwarding function; incoming calls will be forwarded to a specific number if phone is not picked within no answer ring time. Designated Call Forward Number：to enter the specific forwarding number if IT88 enables always forwading / call forwarding busy / no answer forwarding.
IT88 Series Administrator Guide Notification: the message from property manager, this feature is only available when using SDMC or Akuvox SmartPlus. Text MSG: to send or receive or manage the text message here. Owner MSG: if you enable this feature, and no body answer the incoming call within the pre-configure ring time ,the visitor will hear the owner audio message.
IT88 Series Administrator Guide 12. Audio& Video Codec Configuration for SIP Calls 12.1.Audio Codec Configuration Akuvox indoor monitor supports seven types of Codec (iLBC_13_3, iLBC_15_2, L16, PCMU, PCMA, G729, G722 for encoding and decoding the audio data during the call session. Each type of codec varies in terms of sound quality. You can select the specific codec with different bandwidth and sample rate flexibly according to the actual network environment.
IT88 Series Administrator Guide Codec Type Bandwidth Sample Rate Consumption PCMA 64 kbit/s 8kHZ PCMU 64 kbit/s 8kHZ G729 8 kbit/s 8kHZ G722 64 kbit/s 16kHZ iLBC_13_3 8,16 kbit/s 13.3kHZ iLBC_15_2 8,16 kbit/s 15.2kHZ L16 128 kbit/s variable 12.2.Video Codec Configuration IT88 series supports VP8, H263, H264, H265 codec that provides a better video quality at a much lower bit rate with different video quality and payload.
IT88 Series Administrator Guide options: ”QCIF”, “CIF”, “VGA”, “4CIF” and “720P” according to your actual network environment. The default code resolution is 4CIF. Bitrate: select the video stream bit rate (Ranging from 320-2048). The greater the bitrate, the data transmitted in every second is greater in amount therefore the video will be clearer. While the default code bitrate is 2048. Payload: select the payload type (ranging from 90-118) to configure audio/video configuration file.
IT88 Series Administrator Guide 13.1.2. Video Image Capturing To capture video image by pressing Monitor > Capture on device screen. 13.2.Alarm and Arming Configuration Alarm feature is used to connect some alarm detection devices to protect your home safe. Akuvox indoor monitors support 8 alarm connectors which means you can connect 8 different alarm sensors in different rooms of your house.
IT88 Series Administrator Guide Parameter Set-up: Location: set up the location according to where the alarm sensor is installed. You can select among ten location types: “Bedroom”, “Gate”, “Door” “ Guest room”, “Hall”, “Window”, “Balcony”, “Kitchen”, “Study” and "Bathroom”. Zone Type: set up the alarm sensor types. You can select among five sensor types: “Infrared”, “Drmagnet”, “Smoke”, “Gas”, “Urgency”. Trigger Mode: set sensor trigger mode between “NC” and “NO” according to your need.
IT88 Series Administrator Guide Zone type: to select which type of detection device is, including Infrared, Drmagnet, Smoke, Gas, and Urgency. Defence delay: it means when users change the arming mode from other modes, there will be 90 seconds delay time to get activated. Alarm delay: it means when the sensor triggered, there will be 90 seconds delay time to announce the notification. Status: to enable or disable Arming mode on the corresponding Zone. 13.2.4.
IT88 Series Administrator Guide You can upload customized alarm ringtone by choosing the local audio file on web Phone-Audio-Alarm Ringtone Upload interface. Note: The file format of customized ringtone should be .wav. 13.2.7. Alarm Action Configuration The triggering of the alarm sensor can be accompanied by the the actions you configured in forms of HTTP command, SIP Message, Call, Local Relay for different security purposes. 13.2.7.1.
IT88 Series Administrator Guide enabled by using Autop. Call: enable Call if you want you a call to go to a designated SIP or IP number. 13.2.7.2. Configure Alarm Action via HTTP Command To set up the HTTP Command action, you can click “Enable”in the Send HTTP field to enable the actions for the alarm sensor installed in different locations. Then enter the HTTP command provided by the manufacturer of the device on which the action is to be carried. 13.2.7.3.
IT88 Series Administrator Guide To check alarm log on device Settings > Arming Log screen. 13.3.Screen Unlock Setting You can enable screenlock function directly on the device Settings > Display Setting screen. The device screen will be locked over the sleep time. You are required to wake up the device through the face recognition (Face ID) or password. 13.3.1. Screen Unlock by PIN code You can unlock IT88 device screen by entering the pre-configured PIN code when the screen is locked.
IT88 Series Administrator Guide The encryption function provides you with greater security for the intercom call. And, IT88 series support three modes of voice encryption: SRTP(compulsory), SRTP(Optional), ZRTP(Optional) on web Account > Advanced > Encryption interface. Parameter Set-up: Voice Encryption: select encryption mode from four options. If you select to Disable it, the call will not be encrypted.
IT88 Series Administrator Guide 14. Door Access Control Configuration 14.1.Relay Switch Setting 14.1.1. Local Relay Setting Local relays in IT88 indoor monitor can be used to trigger relay for the door access and trigger Chime bell as needed in different scenarios. You can do this configuration on web Phone > Relay > Relay Setting > Local Relay interface. Parameter Set-up: Relay Delay: set the relay delay time after the relay is triggered. Relay Type: set relay action type.
IT88 Series Administrator Guide Remote Control: enable it to trigger local relay by DTMF and vice versa. DTMF: set the DTMF to trigger the local relay when you enable Remote control. 14.1.2. Remote Relay Switch Setting You can use the unlock tab during the call to open the door on web Phone > Relay > Relay Setting > Remote Relay interface. You are required to set up the same DTMF code in the door phone and indoor monitor.
IT88 Series Administrator Guide IP address: enter the web relay IP address. User Name: enter the User name provided by the web relay manufacturer. Password: enter the password provided by the web relay manufacturer.The passwords is authenticated via HTTP and you can define the passwords using “http get” in Action. Web Relay Action: enter the specific web relay action command provided by the web manufacturer for different actions by the web relay.
IT88 Series Administrator Guide Type: select DTMF type among four options: “Inband”, “RFC2833”, “Info+Inband” and “Info+RFC2833” according to your need. How to Notify DTMF: select among four options: “Disable” “DTMF” “DTMF-Relay” “Telephone-Event” according to your need. DTMF Payload: select the payload 96-127 for data transmission identification. Note: Please refer to the chapter Relay Switch Setting for the specific DTMF code setting.
IT88 Series Administrator Guide Password: Enter the device password to be used as part of HTTP command to trigger the local relay. Please refer to the following example: http://192.168.35.127/fcgi/do?action=OpenDoor&UserName=admin&Pa ssword=12345&DoorNum=1 Note: DoorNum in the HTTP command above refers to the relay number #1 to be triggered. 15. Lift Control You can summon lift at home via lift control feature. 15.1.
IT88 Series Administrator Guide Status: click to enable or disable the lift button. Icon: click to select icon for the button. Label: enter the title for the button. HTTP Command: select http:// or https:// for head of http command and enter http command. 15.2.Configure Lift Control Prompt When the lift controller receive the http command, it will feedback the current lift status with a prompt. To do this configuration on web Device > Lift> Hints interface.
IT88 Series Administrator Guide 16. Firmware Upgrade 16.1.1. Configure Alarm Action via HTTP Command Firmwares of different versions for indoor monitor can be upgraded on the device web Upgrade > Basic interface. Note: Firmware files should be .zip format for upgrade. AKUVOX SMART INTERCOM www.akuvox.
IT88 Series Administrator Guide 17. Backup Configuration files can be imported to or exported out of the device to your local PC on the device web Upgrade > Advanced > Others interface if needed. AKUVOX SMART INTERCOM www.akuvox.
IT88 Series Administrator Guide 18. Auto-provisioning via Configuration File 18.1.Provisioning Principle Auto-provisioning is a feature used to configure or upgrade the devices in batch via third party servers. DHCP, PNP, TFTP, FTP, HTTPS are the protocols used by the Akuvox intercom devices to access the URL of the address of the third party server which stores configuration files and firmwares, which will then be used to to update the firmware and the corresponding parameters on the door phone.
IT88 Series Administrator Guide configuration file to update parameters on the devices. For example ： cfg. MAC-based configuration provisioning: MAC-based configuration files is used for the auto-provisioning on a specific device as distinguished by its unique MAC number. And the configuration files named with device MAC number will be matched automatically with the device MAC number before being downloaded for the provisioning on the specific device.
IT88 Series Administrator Guide Power On: select “Power on”, if you want the device to perform Autop every time it boots up. Repeatedly: select “Repeatedly”, if you want the device to perform autop according to the schedule you set up. Power On + Repeatedly: select “Power On + Repeatedly” if you want to combine Power On Mode and Repeatedly mode that will enable the device to perform Autop every time it boots up or according to the schedule you set up.
IT88 Series Administrator Guide Parameter Set-up: Custom Option: enter the DHCP code that matched with corresponding URL so that device will find the configuration file server for the configuration or upgrading. DHCP Option 66: If none of the above is set, the device will automatically use DHCP Option 66 for getting the upgrade server URL. This is done within the software and the user does not need to specify this.
IT88 Series Administrator Guide interface. If an autop schedule is set up, the indoor monitor will perform the auto provisioning on a specific timing according to autop schedule you set up. In addition,TFTP, FTP, HTTP, and HTTPS are the protocols that can be used for upgrading the device firmware and configuration.
IT88 Series Administrator Guide Note: Server Address format: TFTP: tftp://192.168.0.19/ FTP: ftp://192.168.0.19/ (allows anonymous login) ftp://username:password@192.168.0.19/(requires a user name and password) HTTP: http://192.168.0.19/ (use the default port 80) http://192.168.0.19:8080/ (use other ports, such as 8080) HTTPS: https://192.168.0.19/ (use the default port 443) Note: Akuvox do not provide user specified server. Please prepare TFTP/FTP/HTTP/HTTPS server by yourself. 19.
IT88 Series Administrator Guide without your needing to call “Albert" again to wake up the voice assistant., while if you disable it, the voice assistant will be wake up again for each voice command. Not Disturb At Night: move the toggle switch to the left to enable the function. This function is applied when you want the voice assistant to stay silent while carrying out what it is made to do according to your voice commands.
IT88 Series Administrator Guide 5 away mode Use it when you want to change the arming mode to away mode 6 home mode Use it when you want to change the arming mode to home mode 7 open door Use it when you want to open the door 8 9 open door disable DND dream Made it, good night Started it, sweet dreams! Sure, away mode is on OK, start away mode Alright, away mode is opened Made it Made it, have a good day Done, away mode is started Sure, home mode is on OK,
IT88 Series Administrator Guide 10 enable DND Use it when you want to enable the DND mode 11 emergency Use it when you want to dial SOS number 12 13 help me call manager 14 call staff 15 call carer 16 open message ibid ibid use it when you want to call "manager" you name set up in the phonebook use it when you want to call "stuff" you named and set up in the phonebook use it when you want to call "carer" you named and set up in the phonebook use it wh
IT88 Series Administrator Guide 17 18 open monitor homepage use it when you want to Got it ,please check check monitor use it when you want to go Home page is already to home screen for you. 19 enable mute use it when you want to mute your voice on the indoor monitor so that the caller or callee will be not be able to hear you. 20 disable mute use it when you want to unmute your voice on the indoor monitor so that the caller or calle will be be able to hear you.
IT88 Series Administrator Guide will also appear when you call " Tom", and you are required to select the right contact manually. To enable the voice assistant and set the voice assistant-controlled relay on the web Setting > Voice Assistant > Voice Assistant Setting interface, you can tick the check box to enable the voice assistant function. Then go to Voice Command Setting section to elect specific relay to bet triggered via voice assistant. 20. Call Log AKUVOX SMART INTERCOM www.akuvox.
IT88 Series Administrator Guide If you want to check on the calls inclusive of the dial-out calls, received calls, and missed calls in a certain period of time, you can check and search the call log on the device web Contacts > Call Logs interface and export the call log from the device if needed. Parameter Set-up: Capture Delay: set the image capturing starting time when the device goes into video preview.
IT88 Series Administrator Guide debugging , you can set up the function on the web Upgrade > Diagnosis > System Log interface. Parameter Set-up: Log Level: select log levels from 1 to 7 levels. You will be instructed by Akuvox technical staff about the specific log level to be entered for debugging purpose. The default log level is “3”.the higher the level is, the more complete the log is. Export Log: click the Export tab to export temporary debug log file to a local PC.
IT88 Series Administrator Guide Parameter set-up: Specific Port: select the specific ports from 1-65535 so that only the dat a packet from the specific port can be captured. You can leave the field bl ank by default. PCAP: click ”Start” tab and ”Stop” tab to capture the a certain range of d ata packets before clicking Export tab to export the data packets to you L ocal PC. PCAP Auto Refresh: select “Enable” or “Disable” to turn on or turn off the PCAP auto fresh function.
IT88 Series Administrator Guide 22. Device Integration with Third Party 22.1.Enter Applications Screen The content of this part mainly teaches you how to enter the APK interface through hidden operations. To do the configuration on device Settings > System Info interface. you can press on User Mode for 10 times and press “Admin Mode” and press “Confirm” for the confirmation 22.2.
IT88 Series Administrator Guide To configure the installed the third-party app, you can click App Name field to select the specific name of the installed APK files for configuration. Then tick the check boxes of the each field for specific configuration you need. Parameter Set-up: App Name: select the App Name to be configured. Interval Without Operating (Sec): tick the check box to set the app returing time-interval when there is no operation on the device.
IT88 Series Administrator Guide IT88 Android indoor monitor has built in the PBX server which makes the indoor station not only used as a intercom monitor also a SIP PBX, users do not bother to prepare an extra SIP PBX again. The PBX supports call, forward, transfer, conference, ring group feature and so on. You can set up on device screen or web interface. 23.1.PBX Configuration on The Device Enable the PBX feature on device Advance Settings > PBX screen to check and manage SIP accounts. 23.1.1.
IT88 Series Administrator Guide Status: to show whether the account is registered or not. Username: T=to enter the extension number registered onto SIP server. Display Name: to enter the display name of this account, which will show on other devices when making calls. Password: to enter the password of the corresponding users. Enabled Status: to activate SIP account. Call IN/Call Out: the calling status of this account. Calling Party: the calling party number.
IT88 Series Administrator Guide Group Name: the name of a ring group. Quick Dial: a number of this ring group. 23.2.PBX Configuration on The Web Interface You can do the same configuration on web PBX > Basic and PBX > Ring Group interface. 24. Password Modification 24.1.Modify Device Basic Setting Password AKUVOX SMART INTERCOM www.akuvox.
IT88 Series Administrator Guide To do the configuration on device Settings > Advanced Settings > Protected Code screen to choose System Code to change a new password. The default password is 123456. 24.2.Modify Device Advanced Setting Password This password is used to enter the advanced settings of the device, including password settings, account numbers, SOS numbers, network settings, etc.
IT88 Series Administrator Guide 24.4.Modify Browser Password This password is used to lock the browser on the device in case someone abuses the browser for any unwanted application. You can do this configuration on device Settings > Advanced Settings > Protected Code > Browser Code screen. The default password is 123456. 25. System Reboot&Reset 25.1.Reboot 25.1.1.
IT88 Series Administrator Guide To restart to the system setting on device Settings > Advance Settings > Reset&Reboot screen. 25.1.2. Reboot on the Web Interface If you want to restart the device system, you can operate it on the device web Upgrade > Basic interface as well. More over, you can set up schedule for the device to be restarted. To set up the device restart schedule on web Upgrade > Advanced > Reboot Schedule interface. 25.2. Reset 25.2.1.
IT88 Series Administrator Guide If you only want to reset the configuration file to the factory setting instead of the whole device system, you can press Reset Config To Factory Setting tab. 25.2.2. Reset on the Web Interface Device system can also be reset on device web Upgrade > Basic interface without approaching the device. If you only want to reset to the configuration file to the factory setting, you can click Reset Config on the same page. 26. Abbreviations AKUVOX SMART INTERCOM www.akuvox.
IT88 Series Administrator Guide ACS: Auto Configuration Server Auto: Automatically AEC: Configurable Acoustic and Line Echo Cancelers ACD: Automatic Call Distribution Autop: Automatical Provisioning AES: Advanced Encryption Standard BLF: Busy Lamp Field COM: Common CPE: Customer Premise Equipment CWMP: CPE WAN Management Protocol DTMF: Dual Tone Multi-Frequency DHCP: Dynamic Host Configuration Protocol DNS: Domain Name System DND: Do Not Disturb DNS-SRV: Service record in the Domain Name System FTP: File T
IT88 Series Administrator Guide PNP: Plug and Play RFID: Radio Frequency Identification RTP: Real-time Transport Protocol RTSP: Real Time Streaming Protocol MPEG: Moving Picture Experts Group MWI: Message Waiting Indicator NO: Normal Opened NC: Normal Connected NTP: Network Time Protocol NAT: Network Address Translation NVR: Network Video Recorder ONVIF: Open Network Video Interface Forum SIP: Session Initiation Protocol SNMP: Simple Network Management Protocol STUN: Session Traversal Utilities for NAT SNM
IT88 Series Administrator Guide 27. FAQ Q1: How to obtain IP address of IT88? A1: You can use the display screen to get the IP information, just check the IP address at setting, basic info. You can also use Akuvox IP Scanner to search Akuvox devices in the same LAN network. Q2: Do Akuvox devices support Opus codec? A2: For now, only Akuvox Android video IP phone R48G can support Opus audio codec. Door phone and indoor monitor still not supports.
IT88 Series Administrator Guide Q6:Can I connect electrical lock to indoor monitor? A6:Akuox indoor monitor have relay component, so you can connect electrical lock to indoor monitor. Q7:Can I communicate other indoor monitor with indoor monitor? A7:Akuvox device can communicate with each other, no matter it is indoor monitor,door phone or ip phone. Of course indoor monitor can call to other indoor monitor, also if you want, you can set other indoor monitor as auto answer mode.
IT88 Series Administrator Guide 28. Contact Us For more information about the product, please visit us atwww.akuvox.com or feel free to contact us by Sales email: sales@akuvox.com Technical support email: support@akuvox.com Telephone: +86-592-2133061 ext.7694/8162 We highly appreciate your feedback about our products. AKUVOX SMART INTERCOM www.akuvox.
