Product Info
Table Of Contents
- 1.1.Device Start-up Network Selection
- 1.2.Device Home Screen Type Selection
- 1.3.Accessing the Device Setting on the Device
- 1.4.Access the Device Setting on the Web Interface
- 1.5.Language Setting
- 1.6.Time Setting
- 1.7.Screen Display setting on the Device
- 1.8.Screen Display Setting on the Web Interface
- 1.9.Screensaver Configuration
- 1.10.Upload Wall Paper
- 1.11.Status Bar
- 1.12.Upload Device Booting Image
- 1.13.Icon Screen Display Configuration
- 1.14.Volume Configuration
- 1.15.Phone Book Configuration on the Device
- 1.16.Phone Book Configuration on the Web Interface
- 1.17.Device Network Configuration
- 1.18.Device Deployment in Network
- 1.19. Device NAT Setting
- 1.20. Device Bluetooth Setting
- 1.21.Device Wi-Fi Setting
- 1.22.IP call & IP Call Configuration
- 1.23.SIP Call &SIP Call Configuration
- 1.24.SIP Account Registration
- 1.25.SIP Server Configuration
- 1.26.Outbound Proxy Server configuration
- 1.27.SIP Call DND & Return Code Configuration
- 1.28.Device Local RTP configuration
- 1.29.Data Transmission Type Configuration
- 1.30.Call Setting
- 1.31. Intercom Call Configuration
- 1.32.PTime Configuration
- 1.33.SIP Hacking Protection
- 1.34.Emergency Call Setting
- 1.35.RF Setting (Optional)
- 1.36.Multicast Configuration
- 1.37.Call Forwarding Setting
- 1.38.Manage Messages
- 1.39. Configure Voice Message (MWI)
- 1.40.Audio Codec Configuration
- 1.41.Video Codec Configuration
- 1.42.Monitor and Image
- 1.43.Alarm and Arming Configuration
- 1.44.Screen Unlock Setting
- 1.45.Voice Encryption
- 1.46.Remote Control
- 1.47.Relay Switch Setting
- 1.48.Web Relay Setting
- 1.49.Door Unlock Configuration
- 1.50.Configure Lift Control
- 1.51.Configure Lift Control Prompt
- 1.52.Provisioning Principle
- 1.53.Introduction to the Configuration Files for Auto-P
- 1.54.Autop Schedule
- 1.55.DHCP Provisioning Configuration
- 1.56.Static Provisioning Configuration
- 1.57.System Log for Debugging
- 1.58. PCAP for Debugging
- 1.59. User Agent
- 1.60.Enter Applications Screen
- 1.61. Install Third-party App
- 1.62.Modify Device Basic Setting Password
- 1.63.Modify Device Advanced Setting Password
- 1.64.Modify Device Web Interface Password
- 1.65.Modify Browser Password
- 1.66.PBX Configuration on The Device
- 1.67.PBX Configuration on The Web Interface
- 1.68.Reboot
- 1.69. Reset
Android Indoor Monitor Administrator Guide
AKUVOX SMART INTERCOM www.akuvox.com
75
Parameters set up:
Location: to select which location the detection device is located,
including Bedroom, Guest room, Hall, Window, Balcony, Kitchen, Study
and Bathroom.
Zone type: to select the type of detection device, including Infrared,
Drmagnet, Smoke, Gas, and Urgency.
Defence delay: it means when users enable the arming mode, there will
be 90 seconds delay time for the alarm mode to be activated.
Alarm delay: it means when the sensor triggered, there will be 90
seconds delay time to announce the notification.
Status: To enable or disable Arming mode on the corresponding Zone.
1.43.4. Configure Alarm Text
After the alarm sensor is set up, you are allowed to customize your alarm text
shown on the screen when an alarm is triggered on web Arming> Zone
Setting > Customized Alarm interface. Enter the alarm text for the alarm at
each location according to your need.