Product Info
Table Of Contents
- 1.1.Device Start-up Network Selection
- 1.2.Device Home Screen Type Selection
- 1.3.Accessing the Device Setting on the Device
- 1.4.Access the Device Setting on the Web Interface
- 1.5.Language Setting
- 1.6.Time Setting
- 1.7.Screen Display setting on the Device
- 1.8.Screen Display Setting on the Web Interface
- 1.9.Screensaver Configuration
- 1.10.Upload Wall Paper
- 1.11.Status Bar
- 1.12.Upload Device Booting Image
- 1.13.Icon Screen Display Configuration
- 1.14.Volume Configuration
- 1.15.Phone Book Configuration on the Device
- 1.16.Phone Book Configuration on the Web Interface
- 1.17.Device Network Configuration
- 1.18.Device Deployment in Network
- 1.19. Device NAT Setting
- 1.20. Device Bluetooth Setting
- 1.21.Device Wi-Fi Setting
- 1.22.IP call & IP Call Configuration
- 1.23.SIP Call &SIP Call Configuration
- 1.24.SIP Account Registration
- 1.25.SIP Server Configuration
- 1.26.Outbound Proxy Server configuration
- 1.27.SIP Call DND & Return Code Configuration
- 1.28.Device Local RTP configuration
- 1.29.Data Transmission Type Configuration
- 1.30.Call Setting
- 1.31. Intercom Call Configuration
- 1.32.PTime Configuration
- 1.33.SIP Hacking Protection
- 1.34.Emergency Call Setting
- 1.35.RF Setting (Optional)
- 1.36.Multicast Configuration
- 1.37.Call Forwarding Setting
- 1.38.Manage Messages
- 1.39. Configure Voice Message (MWI)
- 1.40.Audio Codec Configuration
- 1.41.Video Codec Configuration
- 1.42.Monitor and Image
- 1.43.Alarm and Arming Configuration
- 1.44.Screen Unlock Setting
- 1.45.Voice Encryption
- 1.46.Remote Control
- 1.47.Relay Switch Setting
- 1.48.Web Relay Setting
- 1.49.Door Unlock Configuration
- 1.50.Configure Lift Control
- 1.51.Configure Lift Control Prompt
- 1.52.Provisioning Principle
- 1.53.Introduction to the Configuration Files for Auto-P
- 1.54.Autop Schedule
- 1.55.DHCP Provisioning Configuration
- 1.56.Static Provisioning Configuration
- 1.57.System Log for Debugging
- 1.58. PCAP for Debugging
- 1.59. User Agent
- 1.60.Enter Applications Screen
- 1.61. Install Third-party App
- 1.62.Modify Device Basic Setting Password
- 1.63.Modify Device Advanced Setting Password
- 1.64.Modify Device Web Interface Password
- 1.65.Modify Browser Password
- 1.66.PBX Configuration on The Device
- 1.67.PBX Configuration on The Web Interface
- 1.68.Reboot
- 1.69. Reset
Android Indoor Monitor Administrator Guide
AKUVOX SMART INTERCOM www.akuvox.com
74
“ Door” “ Guest room” ,“ Hall” ,“Window”, “ Balcony” ,“Kitchen”, “ Study”
and "Bathroom”.
Zone Type: set up the alarm sensor types. You can select among four
sensor types: “Infrared”, “Drmagnet”, “Smoke”, “Gas”, “Urgency”.
Trigger Mode: set sensor trigger mode between “NC” and “NO” according
to your need.
Status: set the alarm sensor status among three options: “Enable”,
“Disable”,”24H”. Select “Enable” if you want to enable to the alarm,
however you are required to set the alarm again after an alarm is
disarmed. Select “ Disable” if you want to disable the alarm, and select
“24H” if you want alarm sensor to stay enabled for 24 hours without
needing to set up the alarm manually again after the alarm is disarmed.
1.43.3. Configure Location-based Alarm
Configure the alarm sensor in the same way you do on the web interface.