About This Manual Thank you for choosing the Akuvox IT82A indoor monitor. This manual is intended for the administrators who need to properly configure the indoor monitor. This manual applies to the 82.228.2.533 version, and it provides all the configurations for the functions and features of the IT82A indoor monitor. Please visit the Akuvox forum or consult technical support for any new information or the latest firmware.
Introduction of Icons and Symbols Warning: Always abide by this information in order to prevent the persons from injury. Caution: Always abide by this information in order to prevent the damages to the device. Note: Informative information and advice from the efficient use of the device. Tip: Useful information for the quick and efficient use of the device.
Related Documentation You are advised to refer to the related documents for more technical information via the link below: https://knowledge.akuvox.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Table of Contents 1.1. Device Start-up Network Selection........................................................ 12 1.2. Device Home Screen Type Selection......................................................12 1.3. Accessing the Device Setting on the Device.........................................13 1.3.1. Accessing Device Basic Setting.................................................. 13 1.3.2. Accessing Device Advanced Setting.......................................... 14 1.4.
1.18. Device Deployment in Network.............................................................42 1.19. Device NAT Setting................................................................................. 43 1.20. Device Bluetooth Setting....................................................................... 43 1.20.1. Device Bluetooth Pairing............................................................ 43 1.20.2. Device Bluetooth Data Transmission.......................................44 1.21.
1.43.7.1. Select Alarm Action Types.............................................. 78 1.43.7.2. Configure Alarm Action via HTTP Command.............. 80 1.43.7.3. Configure Alarm Action via SIP Message.....................81 1.43.7.4. Configure Alarm Action via SIP Call.............................. 81 1.43.8. Check Alarm Log..........................................................................82 1.44. Screen Unlock Setting............................................................................ 83 1.
1.69.1. Reset on the Device...................................................................127 1.69.2. Reset on the Web Interface......................................................
Android Indoor Monitor Administrator Guide 1. Product Overview IT82A is an Android SIP-based with a smooth touch-screen indoor monitor. It can be connected with the Akuvox door phone for audio/video communication, unlocking, and monitoring. Residents can communicate with visitors via audio/video call, and it supports unlocking the door remotely. It is more convenient and safer for residents to check the visitor’s identity through its video preview function.
Android Indoor Monitor Administrator Guide Introduction to Configuration Menu Status: This section gives you basic information such as product information, Network Information, and account information, etc. Account: This section concerns SIP account, SIP server, proxy server, transport protocol type, audio&video codec, DTMF, session timer, etc. Network: This section mainly deals with DHCP&Static IP setting, RTP port setting, and device deployment, etc.
Android Indoor Monitor Administrator Guide Akuvox SmartPlus, please contact Akuvox technical support, and they will help you configure the related settings before using them. SDMC mode: SDMC (SIP Device Management Controller) is a simple and comprehensive software for building management. It provides a topography for a community while offering you a graphical configuration interface for the door access, intercom, monitoring, alarm, etc.
Android Indoor Monitor Administrator Guide directly or on the device web interface. 1.1. Device Start-up Network Selection Akuvox indoor monitor system settings can be either accessed on the device directly or on the device's web interface. After the device boots up initially, you are required to select the network connection for the device. You can either select ethernet or wireless network connection according to your need.
Android Indoor Monitor Administrator Guide 1.3. Accessing the Device Setting on the Device 1.3.1.Accessing Device Basic Setting. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide You can access the device's basic setting and advance setting where you can configure different types of functions as needed. To access the device basic setting by pressing More > Settings. 1.3.2.Accessing Device Advanced Setting To access the advanced setting, press Setting then press Advanced Settings icon. Press password 123456 (by default) to enter the advanced setting. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.4. Access the Device Setting on the Web Interface You can also enter the device IP address on the web browser in order to log in the device web interface by user name and password admin/admin where you can configure and adjust parameter etc. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Tip: You can also obtain the device IP address using the Akuvox IP scanner to log in the device web interface. Please refer to the URL below for the IP scanner application: http://wiki.akuvox.com/doku.php?id=tool:ip_scanner&s[]=ip&s[]=sca nner Note: Google Chrome browser is strongly recommended. The Initial user name and password are “admin” and please be case-sensitive to the user names and passwords entered. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Language and Time Setting 1.5. Language Setting When you first set up the device, you might need to set the language to your need or you can do it later if needed. And the language can either be set up directly on the device or on the device web interface according to your preference. 1.5.1.
Android Indoor Monitor Administrator Guide To configure the language display on the device web Setting > Time/Lang > LCD Language interface. 1.6. Time Setting Time setting can be set up on the device and on the device web interface in terms of time zone, date and time format etc. 1.6.1.Time Setting on the Device To set up time setting on the device Setting > Time screen. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Parameter Set-up: Automatic Date: automatic Date is switched on by default, which allows the date& time to be automatically set up and synchronized with the default time zone and the NTP server (Network Time Protocol). You can also set it up manually by ticking the check box and then enter the time and date you want and press the Save tab to save the setting. Time Zone: select the specific time zone depending on where the device is used.
Android Indoor Monitor Administrator Guide Note: When the Automatic Date&Time toggle switch is toggled off then parameters related to NTP server will become uneditable. And when the switch is toggled on, then time and date will be denied editing. 1.6.2.Time Setting on the Device Web Interface Time setting on the web Phone > Time interface also allows you to set up the NTP server address that you obtained to automatically synchronize your time and date.
Android Indoor Monitor Administrator Guide IT82A indoor monitor allow you to enjoy a variety of screen displays to enrich your visual and operational experience through the customized setting to your preference. 1.7. Screen Display setting on the Device You can configure a variety of features of the screen display in terms of brightness, screen saver and font size, etc. You can do this configuration on device Setting > Display screen.
Android Indoor Monitor Administrator Guide adjust the screen brightness. The default brightness is “145”. Sleep: set the timing for the device screen to be turned off. You can select the timing among eight options: 30 seconds, 1 minute, 2 minutes, 5 minutes, 10 minutes, 30 minutes, 1 hour. For example, if you set it as 1 minute then the screen will be turned off if there is no operation on the device for 1 minute.
Android Indoor Monitor Administrator Guide 3 SDMC+Loca Display pictures from SDMC and the indoor monitor in l Pictures rotation as the screen saver. 4 SDMC Videos Display videos from SDMC as the screen saver. 5 Local Videos Display videos from the indoor monitor as the screen saver 6 SDMC+Loca Display videos from SDMC and the door phone in l Videos rotation as the screen saver. 7 Clock Display the clock as the screen saver.
Android Indoor Monitor Administrator Guide 1.8. Screen Display Setting on the Web Interface IT82A indoor monitor allows you to enjoy a variety of screen displays to enrich your visual and operational experience through the customized setting to your preference. 1.9. Screensaver Configuration 1.9.1.Configure Screensaver on the Device To configure screensaver on device Setting > Display screen.
Android Indoor Monitor Administrator Guide Screen Saver: Slide the switch to enable the screensaver function. Screen Saver Type: select screen saver type among seven options: SDMC Pictures, Local Pictures, SDMC+Local Pictures, SDMC Videos, Local Videos, SDMC+Local Videos, Clock. 1.9.2. Upload ScreenSaver You can upload screen saver pictures/videos separately to the device and to the device web interface for a public purpose or for a greater visual experience.
Android Indoor Monitor Administrator Guide 1.10.Upload Wall Paper You can customize your screen background picture on device web Phone > Display Setting > Wallpaper interface in order to achieve the visual effect and experience you need for your personalized screen background display. 1.11.Status Bar Status bar setting is for you to customize the device status bar color according to your scenarios. You can do this configuration on web Phone > Display Setting > Status Bar interface.
Android Indoor Monitor Administrator Guide Note: The pictures uploaded should be in .png or .zip format. 1.13.Icon Screen Display Configuration IT82A indoor monitor allow you to customize icon display on the home screen and More screen for the convenience of your operation on device web Phone > Key/Display interface. This article helps you to set up the icon display properly on the screens according to your preference. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Parameter Set-up: Type: click to select among sixteen icon options: “ DND”, “Message”,” Contact”, “Call”, “ Display” ,”System info” ,” Setting”, “ Sound”, “Arming”, “ SOS”, “Browser”,” Motion Detection”, “Custom APK”, “Relays”, “ Unlock”, “N/A” is selected, the icon display in the corresponding area will disappear. Value: enter the value if you select the icon type “Custom APK” and “Browser”.
Android Indoor Monitor Administrator Guide Note: You can configure 4 icons in area 1,2,3, and 4 on the home screen. Note: You can configure 6 icons on the More screen. Sound and Volume Configuration AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Akuvox IT82A indoor monitors provide you with various types of ringtone and volume configuration ranging from Mic volume, Ring volume, Talk volume, Tone volume and Media volume. You can configure them on the device directly or on the web interface. 1.14.Volume Configuration 1.14.1. Configure Volume on the Device To set up the volumes on the device Setting > Sound screen. Parameter Set-up: Ring Volume: adjust the incoming call ringtone volume.
Android Indoor Monitor Administrator Guide Ringtone: select ringtone for incoming calls. Notification Sound: select ringtone for the incoming messages. 1.14.1.1. Configure Volume on the Web Interface You can configure the volumes and tones and customize your doorbell sound and alarm ringtone by uploading the audio file to your preference on device web Phone > Audio interface. Note: Doorbell sound files and Alarm Ringtone files to be uploaded must be .WAV or MP3 format.
Android Indoor Monitor Administrator Guide 1.15.Phone Book Configuration on the Device You can configure the contacts list in terms of adding and modifying contact groups or contacts on the device More > Contacts > Local PhoneBook directly. 1.15.1. Add Contacts Parameter Set-up: Contact Name: enter the name and save. Number: enter the IP or SIP number to save. CameraUrl: enter the RTSP URL for video preview. Account1: select which account to use to dial out, Account 1 or Account 2.
Android Indoor Monitor Administrator Guide Note: The RTSP URL format is rtsp://device IP/live/ch00_0. 1.15.2. Edit Contacts Select the exiting contact and click Edit to modify. 1.15.3. Blocklist Settings on the Device you can choose from the contact list the contact you want to add to the block list AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Note: You can delete contacts regardless of whether it is on the All Contacts screen or the Blocklist screen. 1.16.Phone Book Configuration on the Web Interface 1.16.1. Contact Configuration To conduct contact configuration on web Contacts > Local Contacts interface. The existing contacts will show in the below list after their are being added. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Parameter set-up: Name: enter the contact name to be saved. Number: enter the contact number ( SIP or IP number ) to be saved. Group: select Default or Blocklist group. Account: select Account1 or Account2. 1.16.2. Contact Management You can search, display, edit, and delete the contacts in your contacts list on web Contacts > Local Contacts interface. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide You can dial out a number using the contact phone number on web Contacts > Local Contacts interface. 1.16.3. Block List Setting on the Web Interface You can set the blocklist directly in the contact list on the web Contacts > Local Contacts > Contacts List Setting interface or set it when editing a contact. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Note: If you want to remove the contact from the blocklist on the web interface, you can change the group to the "Default" when editing the contact. 1.16.4. Contact Display You can configure the contact display order and control whether to display the discovery device on the device. Parameters Set-up: Contacts Sort By: There are three modes Default, Created time mode for showing the contact list.
Android Indoor Monitor Administrator Guide will only show local phonebook, the contact for discovery mode will be hidden. 1.16.5. Contacts Import and Export on the Web Interface When the contact becomes so many that you can not afford to manage each contact one by one manually, you can import and export the contacts in batch on the device web Contacts > Local Contacts interface. Note: The contact file can only be imported or exportd in .xml or .csv format.
Android Indoor Monitor Administrator Guide 1.17.Device Network Configuration You can check for the door phone’s network connection info and configure the default DHCP mode (Dynamic Host Configuration Protocol) and static IP connection for the device either on the device or on the device web interface. 1.17.1. Configuring Network Connection on the Device To check and configure the network connection on the device Advance Settings > Network screen.
Android Indoor Monitor Administrator Guide Static IP: select the static IP mode by ticking the DHCP check box. When static IP mode is selected, then the IP address, subnet mask, default gateway, and DNS servers address have to be manually configured according to your actual network environment. IP Address: set up the IP Address if the static IP mode is selected. Subnet Mask: set up the subnet Mask according to your actual network environment.
Android Indoor Monitor Administrator Guide To check and configure network connection on the device web Network > Basic interface. Parameter Set-up: DHCP: select the DHCP mode by checking the DHCP box. DHCP mode is the default network connection. If the DHCP mode is selected, then the indoor monitor will be assigned by the DHCP server with IP address, subnet mask, default gateway, and DNS servers address automatically. Static IP: select the Static IP mode by checking off the DHCP square box.
Android Indoor Monitor Administrator Guide 1.18.Device Deployment in Network Akuvox IT82A indoor monitors should be deployed before they can be properly configured in the network environment in terms of their location, operation mode, address and extension numbers as opposed to other devices for device control and the convenience of the management. To deploy the device in the network on web Network > Advanced > Connect Setting interface.
Android Indoor Monitor Administrator Guide 1.19. Device NAT Setting NAT (Network Address Translation) allows hosts in an organization’s private intranet to transparently connect to hosts in the public domain. There is no need for internal hosts to have registered Internet addresses. It is a way to translate the internal private network IP address into a legal network IP address technology. To set up NAT, you can do it on web Account > Advanced > NAT interface.
Android Indoor Monitor Administrator Guide After IT82A indoor monitors turn on the Bluetooth on the device Setting > Bluetooth screen, it can be paired with other device via Bluetooth. 1.20.2. Device Bluetooth Data Transmission To transfer data via bluetooth by pressing Pair new device. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Note: After successful Bluetooth pairing, data transmission can be carried out. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.21.Device Wi-Fi Setting In addition to wired connection, the device also supports Wi-Fi connection. You can set the Wi-Fi on device Advance Settings > WLAN screen. Intercom Call Configuration AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.22.IP call & IP Call Configuration IP calls and SIP calls can be made directly on the intercom device by entering the IP number on the device. And you can also disable the direct IP call if you allow no IP call to be made on the device. To configure the IP call feature and port on the device web Phone > Call Feature > Others interface. Parameter Set-up: Direct IP Call: tick the check box to enable the direct IP call.
Android Indoor Monitor Administrator Guide do for making the IP calls on the device. However, SIP call parameters related to its account, server, and transport type need to configured first before you can make calls on the device. 1.24.SIP Account Registration Akuvox IT82A indoor monitors support two SIP accounts that can all be registered according to your applications. For example, you can switch between the two SIP accounts. The SIP account can be configured on the device and on the device interface.
Android Indoor Monitor Administrator Guide Parameter Set-up: Status: check to see if the SIP account is registered or not. Account: select Account1 or Account2. Account Enabled: check to active the registered SIP account. Display Label: configure the device label to be shown on the device screen. Display Name: configure the name, for example, the device’s name to be shown on the device being called to.
Android Indoor Monitor Administrator Guide Parameter Set-up: Server IP: enter the Server’s IP address number or its URL. Port: set up SIP server port for data transmission. Registration Period: set up SIP account registration time pan. SIP re-registration will start automatically if the account registration fails during the registration time span. The default registration period is “1800”, ranging from 30-65535s. 1.26.
Android Indoor Monitor Administrator Guide Preferred Outbound Proxy Server: enter the SIP address of the outbound proxy server. Preferred Outbound Proxy Port: Enter the Port number for establish call session via the outbound proxy server. Alternate Outbound Proxy Server: set up Backup Server IP for the backup outbound proxy server. Alternate Outbound Proxy Port: enter the Port number for establish call session via the backup outbound proxy server. 1.27.
Android Indoor Monitor Administrator Guide DND Start Time：the start time for DND schedule. DND End Time: the end time for DND schedule. 1.28.Device Local RTP configuration For the device network data transmission purpose, device needs to be set up with a range of RTP port (Real-time Transport Protocol) for establishing an exclusive range of data transmission in the network. To set up device local RTP on web Network > Advanced > Local RTP interface.
Android Indoor Monitor Administrator Guide Parameter Set-up: UDP:select “UDP” for unreliable but very efficient transport layer protocol. UDP is the default transport protocol. TCP: select “TCP” for Reliable but less-efficient transport layer protocol. TLS: select “TLS” for Secured and Reliable transport layer protocol. DNS-SRV: select “DNS-SRV” to obtain DNS record for specifying the location of services. And SRV not only records the server address but also the server port.
Android Indoor Monitor Administrator Guide Parameter Set-up: Auto Answer: turn on the the Auto Answer function by ticking the square box . Auto Answer Delay: set up the delay time (from 0-30 sec.) before the call can be answered automatically. For example, if you set the delay time as 1 second, then the call will be answered in 1 second automatically. Answer Mode: set up the video or audio mode you preferred for answering the call automatically.
Android Indoor Monitor Administrator Guide you are required to configure or edit the numbers in the white-list on web Phone > Call Feature > Auto Answer AllowList interface. SIP/IP numbers can be imported to or exported out of the indoor monitor in batch on web Phone > Call Feature > Allowlist Import/Export interface. Note: SIP/IP number files to be imported or exported must be in either .xml or .csv format.
Android Indoor Monitor Administrator Guide 1.30.3. Live Stream Setting Receive Live Stream on the indoor monitor allows you to see the the video image (one way video stream) from the calling device such as a door phone whether or not you answered the call in audio or video mode, while the video image from your indoor monitor will not be sent to the calling devices in order to protect your privacy. To do the configuration on web Phone > Call Feature >Audio Call Settings interface.
Android Indoor Monitor Administrator Guide Parameter Set-up: Intercom Active: tick the check box to enabled or disabled intercom function. Intercom Mute: tick the check box to enable mute the voice from the callee side and vice versa. Intercom Preview: tick the check box to enable the incoming call preview function. 1.32.PTime Configuration Ptime gives the length of time in milliseconds represented by the media in a packet.
Android Indoor Monitor Administrator Guide 1.33.SIP Hacking Protection Internet phone eavesdropping is a kind of network attack, which aims to eavesdrop on the communication sessions of others in an unauthorized way. Attackers can use this malicious activity to capture and read content containing sensitive and confidential information. SIP hacking prevents SIP call from hacking in the Internet. Parameters Set-up: Prevent SIP Hacking: enable to active this feature during using sip call.
Android Indoor Monitor Administrator Guide To display SOS softkey on web Phone > Key/Display > Home Page Display interface. The icon will show in the main interface or more interface after configured. 1.34.2. SOS Number Settings To set up SOS numbers on device web Phone > Intercom. Parameter Set-up: Call Number: to set up 3 SOS numbers. Once users press SOS key on the home screen (SOS display key shall be set on the web manually), indoor monitors will call out the number in order.
Android Indoor Monitor Administrator Guide 1.35.RF Setting (Optional) IT82A supports RF(Radio Frequency) module to connect a pendent to trigger some actions, like unlocking or making a emergency call. After pairing pendents and indoor monitors, then setup different RF actions on device Advance Settings > RF Settings. After power on the pendent, click Learning and press pendent one time, they will be paired. The green indicator means pairing successfully.
Android Indoor Monitor Administrator Guide 1.36.Multicast Configuration IT82A allows you to conduct one-to-many broadcasting via multicast function on web Phone > Multicast interface. Parameter Set-up: Multicast Setting: to set the indoor monitor in one of the groups or disable this function. Multicast List: to fill in the parameters of multicast group. Indoor monitor will establish multicast calls to other indoor monitors which are set in multicast group.
Android Indoor Monitor Administrator Guide Label: To show the label name on the calling interface if users establish all call. 1.37.Call Forwarding Setting Call Forward is a feature used to redirect an incoming call to the specific third party. Users can redirect the incoming call based on different scenarios. Typically, call forward has three modes: Always Forward/ No Answer Forward/Busy Forward. 1.37.1.
Android Indoor Monitor Administrator Guide Parameter Set-up: Account: to choose which account to implement call forwarding feature. Always Forwarding: to enable always forwarding function; all incoming calls will be automatically forwarded to a specific number. Busy Forwarding: To enable busy forwarding function; incoming calls will be forwarded to a specific number if phone is busy.
Android Indoor Monitor Administrator Guide 1.37.2. Call Forwarding Configuration on the Web Interface To set up forward function on web Phone > Call Feature > Forward Transfer interface. Parameter Set-up: Always Transfer: To enable always forwarding function; all incoming calls will be automatically forward to a specific number. Busy Transfer: To enable busy forwarding function; incoming calls will be forwarded to a specific number if phone is busy.
Android Indoor Monitor Administrator Guide Intercom Message Setting You can read, create, and delete messages on the Message screen. 1.38.Manage Messages You can check, create and clear messages as needed on the indoor monitor Messages screen. Click New to create a new text message and Delete icon to delete the existed messages. Parameter Set-up: New: press this icon to create a new message Delete: press this icon to clear the messages that have been selected.
Android Indoor Monitor Administrator Guide MWI (Message Waiting Indicator) is a notification that notifies you when you have a new voice mail message. To do the configuration on web Account >Advanced >Subscribe interface. Parameter Set-up: MWI Subscribe: tick the check box to enable MWI function. MWI Subscribe Period ： set up interval between the MWI Subscribe messages. Voice Mail Number ： enter the voice mail number for accessing your voice mail messages.
Android Indoor Monitor Administrator Guide 1.40.Audio Codec Configuration Akuvox indoor monitor supports seven types of Codec (iLBC_13_3, iLBC_15_2, L16, PCMU, PCMA, G729, G722) for encoding and decoding the audio data during the call session. Each type of Codec varies in terms of sound quality. You can select the specific codec with different bandwidth and sample rate flexibly according to the actual network environment. To do the configuration on web Account> Advanced > Audio Codecs interface.
Android Indoor Monitor Administrator Guide 1.41.Video Codec Configuration IT82A supports VP8, H263, H264, H265 codec that provides a better video quality at a much lower bit rate with different video quality and payload. To do the configuration on web Account > Advanced > Video Codecs interface. Choose an available video codecs and setup the codecs parameters. Parameter Set-up: Name: check to select the H264 video codec format for the door phone video stream. H264 is the video codec by default.
Android Indoor Monitor Administrator Guide 1.42.Monitor and Image 1.42.1. Monitor Setting You can configure the monitor setting on the web Phone > Monitor interface. Enter IP/SIP number of door phone in Device number and fill in device name. Then set up the RTSP address. The RTSP format of the Akuvox door phone is rtsp://deviceIP/live/ch00_0. you can enable or disable display in the call. If enabled, when there is an incoming call from the monitor, the video will be displayed.
Android Indoor Monitor Administrator Guide You can also import or export the monitor list in batch in the same interface. Import file can only support .xml format. 1.42.2. Video Image Capturing To capture video image by pressing Capture during monitor or a video call. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.43.Alarm and Arming Configuration Alarm feature is used to connect some alarm detection devices to protect your home safety. Akuvox indoor monitors support 8 alarm connectors which means you can connect 8 different alarm sensors in different rooms of your house. For example, connecting a smoker sensor in your kitchen to detect if the gas is leaking, the indoor monitor will ring and send the alarm message to the target, like community property.
Android Indoor Monitor Administrator Guide 1.43.1. Configure Alarm and Arming on the Device To configure the arming and disarm code on device Advance Settings > Arming/Disarm Code screen. Change the current password and save it. To check the zone status on Arming > Zone Status screen. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.43.2. Configure Alarm and Arming on the Web Interface To set up a location-based alarm sensor on the device web Arming> Zone Setting > Zone Setting interface. Parameter Set-up: Location: set up the location according to where the alarm sensor is stalled. You can select among ten location types: “Bedroom”, “Gate”, AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide “ Door” “ Guest room” ,“ Hall” ,“Window”, “ Balcony” ,“Kitchen”, “ Study” and "Bathroom”. Zone Type: set up the alarm sensor types. You can select among four sensor types: “Infrared”, “Drmagnet”, “Smoke”, “Gas”, “Urgency”. Trigger Mode: set sensor trigger mode between “NC” and “NO” according to your need. Status: set the alarm sensor status among three options: “Enable”, “Disable”,”24H”.
Android Indoor Monitor Administrator Guide Parameters set up: Location: to select which location the detection device is located, including Bedroom, Guest room, Hall, Window, Balcony, Kitchen, Study and Bathroom. Zone type: to select the type of detection device, including Infrared, Drmagnet, Smoke, Gas, and Urgency. Defence delay: it means when users enable the arming mode, there will be 90 seconds delay time for the alarm mode to be activated.
Android Indoor Monitor Administrator Guide 1.43.5. Configure Arming mode To switch arming mode, disarm the alarm on Arming screen by pressing their respective icons. Press Disarm icon if you want to clear the Arming Mode. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.43.6. Configure Alarm Ringtone You can upload customized alarm ringtone by choosing the local audio file on web Phone-Audio-Alarm Ringtone Upload interface. Note: The file format of customized ringtone should be .wav. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.43.7. Alarm Action Configuration The triggering of the alarm sensor can be accompanied by the actions you configured in forms of HTTP command, SIP Message, Call, Local Relay for different security purposes. 1.43.7.1. Select Alarm Action Types To select and set up actions on web Arming > Alarm Action interface. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Parameter Set-up: HTTP Command: enable HTTP command if you want the action to be implemented on a designated third party device SIP Message: enable SIP message if you want the SIP message to be sent to a designated SIP account as an action Call: enable Call if you want you a call to go to a designated SIP or IP number. 1.43.7.2.
Android Indoor Monitor Administrator Guide 1.43.7.3. Configure Alarm Action via SIP Message To set up the SIP message action receiver on the same web interface. Enter the SIP account to which you want to send the configured SIP message as an action when the alarm is triggered. 1.43.7.4. Configure Alarm Action via SIP Call To set up the call action, you can enter the SIP or IP number of the device to be called as an action, then enable Alarm Siren for arming zone as needed. AKUVOX SMART INTERCOM www.
Android Indoor Monitor Administrator Guide 1.43.8. Check Alarm Log To check alarm log on device Settings > Alarm Log screen. To delete the existing alarm log by clicking the right side operation icon. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.44.Screen Unlock Setting You can enable screenlock function directly on the device Settings > Display screen. The device screen will be locked over the sleep time. You are required to wake up the device through the face recognition (Face ID) or password. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.44.1. Screen Unlock by Face ID You can unlock device screen by scanning the pre-configured face. To register the face on device Advance Settig > Face ID. Click Add and agree the privacy agreement. Then looking the camera to put your face into the frame on the screen to register. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.44.2. Screen Unlock by PIN Code You can unlock device screen by entering the pre-configured PIN code when the screen is locked. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Note: Default unlock PIN is 123456. 1.45.Voice Encryption The encryption function provides you with greater security for the intercom call. And Akuvox indoor monitors support three modes of voice encryption: SRTP(compulsory), SRTP(Optional), ZRTP(Optional) on web Account > Advanced > Encryption interface. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Parameter Set-up: Voice Encryption: select encryption mode from four options. If you select to Disable it, the call will not be encrypted. SRTP(Compulsory), all audio signals (technically speaking it is RTP streams) will be encrypted to improve security. SRTP(Optional), encrypts voice from the called party, if the called party also enables SRTP, the voice signals will also be encrypted.
Android Indoor Monitor Administrator Guide Door Access Control Configuration 1.47.Relay Switch Setting 1.47.1. Local Relay Setting Local relays in Akuvox indoor monitor can be used to trigger relay for the door access and trigger Chime bell as needed in different scenarios. You can do this configuration on web Phone > Relay > Relay Setting > Local Relay interface. Parameter set-up: Relay Delay: set the relay delay time after the relay is triggered. Relay Type: set relay action type.
Android Indoor Monitor Administrator Guide 1.47.2. Remote Relay Switch Setting You can use the unlock tab during the call to open the door on web Phone > Relay > Relay Setting > Remote Relay interface. You are required to set up the same DTMF code in the door phone and indoor monitor. Parameter Set-up: DTMF Code: To set DTMF code for the remote relay, which is “#” by default. 1.48.
Android Indoor Monitor Administrator Guide Parameter Set-up: IP address: enter the web relay IP address. User Name: enter the User name provided by the web relay manufacturer. Password: enter the password provided by the web relay manufacturer.The passwords is authenticated via HTTP and you can define the passwords using “http get” in Action. Web Relay Action: enter the specific web relay action command provided by the web manufacturer for different actions by the web relay.
Android Indoor Monitor Administrator Guide DTMF codes can be configured on the web Account > Advanced > DTMF interface where you can set up identical DTMF code on the corresponding intercom devices, which allows residents to enter the DTMF code on the soft keypad or press DTMF code attached unlock tab on the screen to unlock the door for visitors etc., during a call.
Android Indoor Monitor Administrator Guide the door access. To do this configuration on web Intercom > Relay > Open Relay Via HTTP interface. Parameter Set-up: Status: Enable it to allow the relay to be triggered remotely using HTTP command. Username: Enter the device username to be used as a part of HTTP command to trigger the local relay. Password: Enter the device password to be used as part of HTTP command to trigger the local relay. Please refer to the following example: http://192.168.
Android Indoor Monitor Administrator Guide 1.49.3. Unlock by Icon Button To setup the touch unlock key in IT82A for unlock on web Phone >Key/Display interface. 1.49.4. Unlock by SOS Call To choose the Relay type as SOS Action on web Phone > Relay interface. When call out the SOS number, the relay will be triggered. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Lift Control You can summon lift at home via lift control feature. 1.50.Configure Lift Control To enable and set the display status Lift icon on device web Phone > Lift> Lift Control interface. Parameter set-up: Status: click to enable or disable the lift1 button. Icon: click to select icon for the button. Label: enter the title for the button. HTTP Command: select http:// or https:// for head of http command and enter http command.
Android Indoor Monitor Administrator Guide 1.51.Configure Lift Control Prompt When the lift controller receive the HTTP command, it will feedback the current lift status with a prompt. To do this configuration on web Phone > Lift> Hints interface. Edit the HTTP Status Code, feedback code from Lift control board. If there are huge amounts of prompts need to be add, you can click Export tab to export a template, after editing to import/export. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Firmware Upgrade Firmwares of different versions for indoor monitor can be upgraded on the device web Upgrade > Basic interface. Note: Firmware files should be .zip format for upgrade. Backup AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Configuration files can be imported to or exported out of the device to your local PC on the device web Upgrade > Advanced > Others interface if needed. Auto-provisioning via Configuration File AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.52.Provisioning Principle Auto-provisioning is a feature used to configure or upgrade the devices in batch via third party servers. DHCP, PNP, TFTP, FTP, HTTPS are the protocols used by the Akuvox intercom devices to access the URL of the address of the third party server which stores configuration files and firmwares, which will then be used to to update the firmware and the corresponding parameters on the door phone. Please see the flow chart below: 1.53.
Android Indoor Monitor Administrator Guide Configuration files have two formats for the auto-provisioning. one is the general configuration files used for the general provisioning and other one is the MAC-based configuration provisioning.
Android Indoor Monitor Administrator Guide schedule. To set up the schedule on device web Upgrade > Advanced > Automatic Autop interface. Please see the picture below: Parameter Set-up: Power On: select “Power on”, if you want the device to perform Autop every time it boots up. Repeatedly: select “ Repeatedly”, if you want the device to perform autop according to the schedule you set up.
Android Indoor Monitor Administrator Guide from 128-255), you are required to configure DHCP Custom Option on the web Upgrade > Advanced > Automatic Autop interface. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Note: The custom Option type must be a string. The value is the URL of TFTP server. Parameter set-up: Custom Option: enter the DHCP code that matched with corresponding URL so that device will find the configuration file server for the configuration or upgrading. DHCP Option 66: If none of the above is set, the device will automatically use DHCP Option 66 for getting the upgrade server URL.
Android Indoor Monitor Administrator Guide 1.56.Static Provisioning Configuration You can manually set up a specific server URL for downloading the firmware or configuration file on device web Upgrade > Advanced > Automatic Autop interface. If an autop schedule is set up, the indoor monitor will perform the auto provisioning on a specific timing according to autop schedule you set up.
Android Indoor Monitor Administrator Guide Parameter set-up: URL: set up TFTP，HTTP，HTTTPS，ftp server address for the provisioning User Name: set up a user name if the server needs an user name to be accessed to otherwise leave it blank. Password: set up a password if the server needs a password to be accessed to otherwise leave it blank. Common AES Key: set up AES code for the intercom to decipher general Auto Provisioning configuration file.
Android Indoor Monitor Administrator Guide Note: server Address format: TFTP: tftp://192.168.0.19/ FTP: ftp://192.168.0.19/ (allows anonymous login) ftp://username:password@192.168.0.19/(requires a user name and password) HTTP: http://192.168.0.19/ (use the default port 80) http://192.168.0.19:8080/ (use other ports, such as 8080) HTTPS: https://192.168.0.19/ (use the default port 443) Tip: Akuvox do not provide user specified server.
Android Indoor Monitor Administrator Guide Voice Assistant You can configure voice assistant named "Albert" to perform a variety of functions related to intercom call, open-door, arming modes etc. on the device. and you can also set up the specific relay to be triggered by the voice assistant for the door access control. To configure the voice assistant on device Settings > Voice Assistance screen. Parameter Set-up Language Type: select the language according to your need.
Android Indoor Monitor Administrator Guide stay silent while carring out voice commands. Supported Command: acocrding to your need. what it is made to do according to your enable or disable the 22 voice comands Please see the voice command details below: N O 1 Voice Command Intruder mode off 2 Clear arming night mode 3 Description Voice Prompt Use it when you want to Please Input Password clear the arming mode when the arming alarm is triggered.
Android Indoor Monitor Administrator Guide 5 away mode Use it when you want to change the arming mode to away mode 6 home mode Use it when you want to change the arming mode to home mode 7 open door Use it when you want to open the door 8 9 open door disable DND Sure, away mode is on OK, start away mode Alright, away mode is opened Made it Made it, have a good day Done, away mode is started Sure, home mode is on OK, start home mode Alright, home mode is opened
Android Indoor Monitor Administrator Guide 10 enable dnd Use it when you want to enable the DND mode 11 emergency Use it when you want to dial SOS number 12 13 help me call manager 14 call staff 15 call carer 16 open message ibid ibid use it when you want to call "manager" you name set up in the phonebook use it when you want to call "stuff" you named and set up in the phonebook use it when you want to call "carer" you named and set up in the phonebook use
Android Indoor Monitor Administrator Guide you 17 18 open monitor homepage use it when you want to Got it ,please check check monitor use it when you want to go Home page is already to home screen for you. 19 enable mute use it when you want to mute your voice on the indoor monitor so that the caller or callee will be not be able to hear you. 20 disable mute use it when you want to unmute your voice on the indoor monitor so that the caller or calle will be be able to hear you.
Android Indoor Monitor Administrator Guide To enable the voice assistant and set the voice assistant-controlled relay on the web Device Setting > Voice Assistant interface, you can tick the check box to enable the voice assistant function. Then go to Voice Command Setting section to elect specific relay to bet triggered via voice assistant. Call Log AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide If you want to check on the calls inclusive of the dial-out calls, received calls, and missed calls in a certain period of time, you can check and search the call log on the device web Contacts > Call Logs interface and export the call log from the device if needed. Parameter Set-up: Capture Delay: set the image capturing starting time when the device goes into video preview.
Android Indoor Monitor Administrator Guide Debug 1.57.System Log for Debugging System log in the indoor monitor can be used for debugging purpose. If you want to export the system out to a local PC or to a remote server for debugging , you can set up the function on the web Upgrade > Advanced > System Log interface. Parameter Set-up: LogLevel: select log levels from 1 to 7 levels. You will be instructed by Akuvox technical staff about the specific log level to be entered for debugging purpose.
Android Indoor Monitor Administrator Guide Remote System Server: enter the remote server address to receive the the device And the remote server address will be provided by Akuvox technical support. 1.58. PCAP for Debugging PCAP in Akuvox indoor monitor is used to capture the data package going in and out of the devices for debugging and troubleshooting purpose. You can set up the PCAP on the device web Upgrade > Advanced > PCAP interface properly before using it.
Android Indoor Monitor Administrator Guide 1.59. User Agent User agent is used for the identification purpose when you are doing analysis on the SIP data packet. To do this configuration on web Account > Advanced interface. Device Integration with Third Party 1.60.Enter Applications Screen The content of this part mainly teaches you how to enter the APK interface through hidden operations. To do the configuration on device Settings > System Info interface.
Android Indoor Monitor Administrator Guide 1.61. Install Third-party App You can install the third-party App to your device on the device web Phone > App interface. Choose a suitable .apk file from PC to upload. To configure the installed the third-party app on web Phone > Key/Display > Third Party APK Control, you can click App Name field to select the specific name of the installed APK files for configuration. Then tick the check boxes of the each field for specific configuration you need.
Android Indoor Monitor Administrator Guide Parameter Set-up: App Name: select the App Name to be configured. Interval Without Operating (Sec): tick the check box to set the app returing time-interval when there is no operation on the device. Start Up Enable: tick the check box of Start UP Enable if you want to the app to be run automatically when the device is turned on.
Android Indoor Monitor Administrator Guide Show App Icon: tick the box if you wabt the app icon to be displayed on the screen. Password Modification 1.62.Modify Device Basic Setting Password To do the configuration on device Advance Settings > System Code screen to change a new password. The default password is 123456. 1.63.
Android Indoor Monitor Administrator Guide 1.64.Modify Device Web Interface Password To modify web interface password, you can do it on device web Security > Basic > Web Password Modify interface. Select "Admin" for the administrator account and " User" for the User Account. Click the Change Password tab to change the password. Note: There are two accounts, one is admin, its password is admin, the other is user, its password is user. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.65.Modify Browser Password This password is used to lock the browser on the device in case someone abuses the browser for any unwanted application. You can do this configuration on device Advance Settings > App Protected Code screen. The default password is 123456. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide PBX Feature Android indoor monitor has built in the PBX server which makes the indoor station not only used as a intercom monitor also a SIP PBX, users do not bother to prepare an extra SIP PBX again. The PBX supports call, forward, transfer, conference, ring group feature and so on. You can set up on device screen or web interface. 1.66.
Android Indoor Monitor Administrator Guide 1.66.2. Manage PBX Accounts You can check the basic PBX information like PBX server and port and accounts status. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Parameter Set-up: Status: to show whether the account is registered or not. Username: To enter the extension number registered onto SIP server. Display Name: Tt enter the display name of this account, which will show on other devices when making calls. Password: to enter the password of the corresponding users. Enabled Status: to activate SIP account. Call IN/Call Out: the calling status of this account.
Android Indoor Monitor Administrator Guide receiving an incoming call, the numbers in one group will be ring up at the same time. Parameter Set-up: Group Name: the name of a ring group. Quick Dial: a number of this ring group. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide 1.67.PBX Configuration on The Web Interface You can do the same configuration on web PBX > Basic and PBX > Ring Group interface. AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide System Reboot&Reset 1.68.Reboot 1.68.1. Reboot on the Device If you want to reboot the system setting of the device, you can operate it directly on the device setting screen or on the device web interface. To reboot to the system setting on device Settings >Reboot screen. 1.68.2. Reboot on the Web Interface If you want to reboot the device system, you can operate it on the device web Upgrade > Basic interface as well.
Android Indoor Monitor Administrator Guide To set up the device reboot schedule on web Upgrade > Advanced > Reboot Schedule interface. 1.69. Reset 1.69.1. Reset on the Device If you want to reset the whole device system to the factory setting, you can operate it directly on the device Advance Settings > Reset screen. If you only want to reset the configuration file to the factory setting instead of the whole device system, you can press Reset Config To Factory Setting tab. AKUVOX SMART INTERCOM www.
Android Indoor Monitor Administrator Guide 1.69.2. Reset on the Web Interface Device system can also be reset on device web Upgrade > Basic interface without approaching the device. If you only want to reset to the configuration file to the factory setting, you can click Reset Config on the same page.
Android Indoor Monitor Administrator Guide COM: Common CPE: Customer Premise Equipment CWMP: CPE WAN Management Protocol DTMF: Dual Tone Multi-Frequency DHCP: Dynamic Host Configuration Protocol DNS: Domain Name System DND: Do Not Disturb DNS-SRV: Service record in the Domain Name System FTP: File Transfer Protocol GND: Ground HTTP: Hypertext Transfer Protocol HTTPS: Hypertext Transfer Protocol Secure Socket Layer IP: Internet Protocol ID: Identification IR: Infrared LCD: Liquid Crystal Display LED: Light
Android Indoor Monitor Administrator Guide URL: Uniform Resource Locator VLAN: Virtual Local Area Network WG: Wiegand AKUVOX SMART INTERCOM www.akuvox.
Android Indoor Monitor Administrator Guide Contact US For more information about the product, please visit us atwww.akuvox.com or feel free to contact us by Sales email: sales@akuvox.com Technical support email: support@akuvox.com Telephone: +86-592-2133061 ext.7694/8162 We highly appreciate your feedback about our products. AKUVOX SMART INTERCOM www.akuvox.
