Technical Specifications

Data sheets are subject to change without notice. For the latest version, please check the product page at www.tccmaterials.com
Application
1. Use cartridge in standard caulking gun. Trim cartridge tip to
desired bead size.
2. Use in joints of maximum width and depth of ⅜ in. (9.6 mm).
Deep cracks can be partially filled with sand or backer rod
prior to application.
3. The repair can be tooled to even out the surface. Excess
material may be cleaned with a damp cloth before drying.
4. Air and surface temperature should be above 40°F (4°C) for
proper application. Do not apply if rain threatens or is
predicted within 12 hours.
Curing
Product should be air-cured. Wait at least 24 hours before
painting. Use latex paints only.
Clean Up
Use soapy water to clean hands and tools immediately after
use. Dried material must be mechanically removed.
Limitations
• Follow all industry standard safety procedures when handling,
such as gloves and eye protection.
• Do not use for structural repairs to a badly damaged wall.
• Do not apply over concrete cured less than 7 days, or is
frozen or contains frost.
Safety
READ THE SAFETY DATA SHEET (SDS) BEFORE USING
THIS PRODUCT. SDS information is available on our website:
tccmaterials.com
Cautions
Read complete cautionary information printed on product
container prior to use.
This Product Data Sheet has been prepared in good faith on the
basis of information available at the time of publication. It is
intended to provide users with information about and guidelines
for the proper use and application of the covered Akona brand
product(s) under normal environmental and working conditions.
Because each project is different, TCC Materials cannot be
responsible for the consequences of variations in such
conditions, or for unforeseen conditions.
6. AVAILABILITY
To locate Akona products in your area, please contact:
Phone: [phone]
Website: tccmaterials.com
7. WARRANTY
Seller warrants that its product will conform to and perform in
accordance with the product specifications. The foregoing
warranty is in lieu of all other warranties, expressed or implied,
including, but not limited to those concerning merchantability
and fitness for a particular purpose. Because of the difficulty in
ascertaining and measuring damages hereunder, it is agreed
that Seller’s liability to the Buyer shall not exceed the total
amount billed and billable to the Buyer for the product
hereunder.
1. PRODUCT NAME
Akona
®
Mortar Repair
2. MANUFACTURER
Akona Manufacturing, LLC
A TCC Materials Company
2025 Centre Pointe Blvd., Suite 300
Mendota Heights, MN 55120 USA
Phone: [phone]
Web: tccmaterials.com
3. PRODUCT DESCRIPTION
Akona Mortar Repair is designed for tuck-pointing, repairing,
and sealing mortar joints and cracks in masonry units such as
stone, brick and block walls. The product is gray in color and
designed to blend in with the texture of surrounding mortar.
Mortar Repair is a sanded acrylic formulation that is fast
drying, paintable and provides superior adhesion to masonry.
For maximum joint width ⅜ in. (9.6 mm) and maximum depth
⅜ in. (9.6 mm).
Features and Benefits
• Ready to use
• Superior adhesion
• Durable and flexible
• Fast drying
When/Where to Use
• Fills mortar joints
• Vertical repairs
• Masonry finish
4. TECHNICAL DATA
Available Sizes
• 10.1 oz. (0.3 L) tube (BOM #103174)
Coverage
Each 10.1 oz. tube yields approximately 10 lin. ft. (3 m) at ⅜ x
⅜ in. (9.6x9.6 mm) joint
5. INSTALLATION
Preparation
Read all directions before starting work. Proper surface
preparation is crucial to achieving a successful application.
1. Always remove all loose and unsound materials. Thoroughly
clean all surfaces of dirt, dust, grease, or other contaminants
which could interfere with bonding.
2. For better adhesion, surfaces should be dry.
Note: It is the responsibility of the installer/applicator to ensure
the suitability of the product for its intended use.
MORTAR REPAIR
Typical Values • Akona Mortar Repair
Initial Set Time Approximately 30 minutes
Final Set Time Approximately 60 minutes
Tuckpointing, repairing, and sealing mortar joints and cracks in masonry units