Owner`s manual

Syncron user manual. Virtual DJ LE functions.
27

correspond to samples 1 to 4. Buttons 1 to 4 from the right deck
samples correspond to 5 to 8.
In addition to enabling / disabling the reproduction of a sample,
these buttons also allow you to set certain parameters for the
sample while maintaining pressure. If for example you hold down
the 4 button from the left deck can modify parameters for this
sample. Below is a list of controls that modify these parameters for
the sample:
- Turn FOLDER (4): multiplied or divided by 2 the size of the
sample.
- Press FOLDER (4): Change the playback mode of the sample of
continuous to simple and vice versa.
- Rotate the wheel (17): Adjust the volume of the sample.
If you press one of these buttons while holding down SHIFT will
start recording a sample and record what is playing on the deck
selected (see point 9). Meanwhile, the button will illuminate
intermittently. To stop recording press the button again while
holding down the SHIFT. In case when recording starts and has an
active loop on the deck selected, the Loop will be recorded
immediately and will not be necessary to stop recording.
8. DELETE (CLEAR): We must press a Hot Cue button while holding
down this button to delete the corresponding cue point. We need to
be in Hot Cue mode as in Sample mode this button has no function.
SMART CUE on or off by pressing this button while holding down
the SHIFT. When the function is active the LED will light.
9. PRE LISTENING: Enable or disable the pre listening to the
channel to the deck upon which we are acting.
Pressing the button while holding down SHIFT select the channel.
The channel is selected will be recorded when recording a sample
and its waveform is superimposed on the others.
10. RANGE: Select the value of RANGE between 6, 10, 16 and 100%
values. The corresponding LED will light.
To reset the pitch must press this button while holding down SHIFT.
While it is resetting, the 10% LED lights.
11.KEY LOCK: Lock the tone of the song. The LED will illuminate to
indicate that it is locked.
Pressing this button while SHIFT is pressed select the deck on
which we act 1 or 3 on the left as the left deck. Functionally
equivalent to the right deck. This affects the automatic crossfader
function.
12. EFFECTS: Pressing the buttons ECHO, FLANGER and SKID select
and activate the corresponding effect. If before activating the effect
we need to adjust its parameters can press the buttons while
holding down SHIFT to select but not activate the effect.
Should you wish to select an effect for which we have no direct
access will press Y or X while holding down SHIFT. With X go to the
following effect on the list and with Y to the prior effect. To enable
the effect need to hold down SHIFT while you press HOLD.
To configure the parameters of the effects, we must hold X and
move the wheel to the parameter 1 or hold down Y and move the
wheel to parameter 2.
FILTER and KEY (HOLD) work differently from other effects. Pressing
Filter is activated and through the wheel can adjust its value. When
you press the button again, the Filter value is reset and the wheel
returns to its previous operation. A short press on the button HOLD
resets KEY value, and if held down by the wheel can adjust its value.
13. SEARCH: These buttons allow you to perform a fast search
backwards or forwards through the selected topic, either in play
mode or not.
14. WHEEL MODE: Allows you to select between three modes of
operation of the wheel.
VINYL: In this mode when you touch the metal top of the wheel
playback stops and you can “scratch” moving the wheel. If you
move the wheel without touching the metal part, there will be a
"PITCH BEND."
A. CUE: This mode is very similar to VINYL but in this case touch
the metal of the wheel the playback point jumps to the last cue
used.
CDJ: In this mode even touch the metal part will be a "PITCH BEND”
15. TIME: If you turn the wheel while holding down this button will
perform a quick search through the subject.
Pressing the button while holding down SHIFT lock the PITCH.
16. SGL / CNT: Pressing enable or disable the automatic blending
of the themes of the playlist. If you press SGL/CNT while SHIFT is
pressed the current song will be skipped in the mixture if the
automatic mixture is activated.
17. WHEEL: The main functions of the wheel are explained in item
(14) although it can be used to adjust multiple parameters for loops
or effects. Below is a list of parameters that can be adjusted with
the wheel:
- Search: Quick Search (by holding down TIME).
- Loop IN Adjust: Change the starting point of the loop (press SHIFT
+ IN).
- Loop OUT Adjust: Change the end point of the loop (press SHIFT
+ OUT).
- Loop MOV: Moving loop (press SHIFT + RELOOP).
- Parameter 1 effect (hold X).
- Parameter 2 effect (hold Y).
- Key: Parameter setting key (hold HOLD).
- Filter: filter parameter setting (press FILTER)
- Video FX Control: Adjust video effect parameter (in video mode
hold SHIFT).
- Sample Volume: Modify sample volume (hold the play button for
the sample of what we want to change the volume).
18. CUE PLAY: When you press this button, if the playback is
paused playback begins. If you are playing, the playback point
jumps to the last CUE point has been established and continuous
play.
19. CUE: If we are in pause (
|| ) at a point where there is no cue
point and press the button, setting a new cue point. If we're
playing, it pauses and skips to the place where the last set cue
point. If we are in a cue point and pause by pressing the button will
play the song from the cue point until you release the button, when
it returns to the cue point.
20. PLAY / PAUSE: Pressing begin playback. In case you are playing
the song, it pauses.
21. SHIFT / TAP: taping it at the beat rhythm sets a new value to
beat for the track being played.
While holding down this button, the rest of the controller buttons
change their function.
22. PITCH BEND: accelerate or decelerate playback while keeping
the button pressed. When you release it back to its original
playback speed.
23. PITCH SLIDER: This control is used to adjust the pitch rate of
reproduction in a defined range. If you change the pitch by
software, the hardware will never change its value until it reaches
the current value of pitch.