OPERATING INSTRUCTIONS MANUAL DE INSTRUCCIONES MODE D’EMPLOI CDC-X927M YUC STEREO CAR CD RECEIVER RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA AUTOMOVIL ENGLISH ESPAÑOL FRANÇAIS OWNER’S RECORD For your convenience, record the model number and serial number (you will find them on the bottom side of your set) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty. Model No. CDC-X927M Serial No.
PRECAUTIONS TABLE OF CONTENTS • Use only in a 12-volt DC negative-ground electrical system. • Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit. • When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit. • Do NOT attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to the eyes.
THEFT PROTECTION Adjusting the volume (Retractable Front Panel) 1 Turn AUDIO CONTROL. When your car’s ignition switch is turned off, the front panel will be retracted automatically as if there were no car audio in the console. When the ignition switch is set to ACC or ON position, the front panel will appear automatically. Muting the sound Note MUTE indicator flashes. To restore volume, briefly press PWR/MUTE again. Do not touch and put excessive pressure on the front panel while it is rotating.
Restoring the factory settings 1 Press BAND repeatedly to select the desired band 1 Turn off the unit. 2 Press and hold DISP until “LEVEL --” appears on the 2 Press TUNEi (to move to higher frequencies) or (F1, F2, F3, A1 or A2). display. Note You can restore the factory settings only for VOL, BASS, TRE, BAL, FAD, H-BASS, DSSA and BBE as well as aligned source volume levels. Setting the beep tone 1 Turn off the unit. 2 Press and hold SEL until “BEEP” appears on the display.
Presetting stations automatically CD PLAYER OPERATION (Auto Memory) 1 Press BAND repeatedly to select the desired band (F1, F2, F3, A1 or A2). 2 Press and hold PS/A.ME until automatic presetting starts. “A MEM” appears on the display. The unit automatically stores up to 6 stations for each band. After completion of automatic presetting, the unit tunes in to all the stations stored on the preset station buttons in order (Preset Scan). To cancel automatic presetting, press PS/A.ME again.
1 Connect a cassette/MD/MP3 portable player or other Notes • When you play a CD that is already inserted, CD play starts at the point where it stopped the previous time. A newly inserted CD starts from the first track. • A CD-R or CD-RW may take some time to start playing back, but this is not a malfunction. • If a CD-R or CD-RW with no data or incompatible data is inserted, “ERROR03” will appear on the display. (See the section “TROUBLESHOOTING”.) The unit cannot play such discs.
CARD REMOTE CONTROL Names of parts Replacing the battery 1 Insert the tip of a pointed object A into the hole B and pull out the battery holder to remove the lithium battery (CR2025). Remote control (back) BAND TAPE CD CD-CH SKIP REW FF TUNING / DISC UP DOWN Battery holder VOLUME 2 Install a new lithium battery (CR2025) with the ) side facing up in the battery holder. 1 BAND button 2 TAPE button (This button is not available with this unit.
CD CHANGER OPERATION Playing a CD You can play CDs from a connected AIWA CD Changer. For detailed information on installing a CD Changer, refer to the Installation and Connection manual supplied with the CD Changer. RNDM One Disc Repeat Play You can play all tracks on a disc repeatedly. 1 Press REP during CD Changer play. “REP” appears on the display. To cancel Repeat Play, press REP again. One Track Repeat Play You can play a track repeatedly. 1 Press REP1 during CD Changer play.
Reset button GENERAL If a CD does not operate properly, press the reset button with a pointed object such as a pencil, etc. Note that all your settings will be erased if this button is pressed. Power-Supply Voltage: 14.4 V (11 to 16 V allowable), DC, negative ground Load Impedance: 4 Ω Tone Control: Bass ± 10 dB at 100 Hz, Treble ± 10 dB at 10 kHz Preamp Output Voltage (load impedance): 2.
Printed in Indonesia
