d OPERATING INSTRUCTIONS MANUAL DE INSTRUCCIONES MODE D’EMPLOI CDC-X20M YU CDC-X15 YU STEREO CAR CD RECEIVER RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA AUTOMOVIL ENGLISH ESPAÑOL FRANÇAIS OWNER’S RECORD c For your convenience, record the model number and serial number (you will find them on the bottom of your set) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty. Model No. CDC-X20M, CDC-X15 Serial No.
TABLE OF CONTENTS PRECAUTIONS .................................................................................................................................. 3 DETACHING THE CONTROL PANEL ............................................................................................... 4 CONTROL PANEL .............................................................................................................................. 5 TURNING ON/OFF THE UNIT ........................................................
PRECAUTIONS • Do not attempt to disassemble this unit. Laser rays from the optical pickup are dangerous to the eyes. • Make sure that pins or other foreign objects do not get inside the unit; they may cause malfunctioning, or a safety hazard such as electrical shock or exposure of laser rays. • When your car is parked under direct sunlight in summer, there may be a considerable rise in temperature inside the car. Ensure to let the ambient temperature cool down before operating the unit.
DETACHING THE CONTROL PANEL You can detach the control panel from the unit and carry it with you when you leave your car unattended. 1 If a disc is inserted, remove it to prevent possible damage to the unit. 2 Press PWR to turn the unit off. 2 3 While supporting the control panel with one hand, 3 press % to release one side of the panel. Care must be taken not to drop the panel as it may suddenly eject at this point.
CONTROL PANEL 1 2 9 0! 3 4 5 @ # 6 $ 7 % ^ & 8 * ( Display window DISC ST RNDM PROG INT RPT1 1 % (detach) button 2 PWR (power) button 3 A.
TURNING ON/OFF THE UNIT To turn on the unit Press PWR or any other button (except %). To turn off the unit Press PWR. SELECTING FUNCTION To select the function Press FUNC repeatedly. The function changes in the following order. Radio 1 EN 6 CD CD changer* * CMT indicator lights up when ADC-M35 is connected.
SOUND ADJUSTMENTS 1 Press MOD/LD to select the mode you want to adjust from VOL (volume), BAS (bass), TRE (Treble), BAL (balance), and FAD (fader). The mode indicator lights up in the following order. 1 The selected mode changes to the volume mode when MOD/LD is pressed for more than 5 seconds. 2 Press + or - (for less than 0.5 seconds) to adjust the sound quality. To change the level rapidly, press and hold + or - down longer. 2 + side - side Increases the volume level. Decreases the volume level.
RADIO OPERATION 1 Press any button (except %) to turn on the unit. The radio frequency is displayed. If the radio frequency is not displayed, press FUNC to select the radio operation. 1 2 Press BAND to select the desired band from FM1, FM2, FM3, and AM. The band indicator [FM1, FM2, FM3, or AM] is displayed. 2 3 Press TUNE M/N repeatedly to tune in the desired station. Press N to increase and M to decrease the frequency. To change the frequency rapidly, press and hold N or M down longer.
Note • FM1, FM2, and FM3 have the same frequency range. • ST indicator lights up when an FM stereo broadcast is received with a sufficient signal strength. Seek Tuning The seek function is used to search for the station automatically. 1 Press BAND to select the desired band. 2 Press SEEK r/t to start the seek function. Press t to search for the higher frequencies and r for the lower frequencies. The seeking stops when the nearest station with good reception is tuned in.
PRESETTING STATIONS Up to 6 stations for each band [FM1, FM2, FM3, and AM] can be stored on the preset station buttons. 1 Press BAND to select the band from FM1, FM2, FM3, and AM. 1 2 Tune in the station to be preset. 2 3 Press one of the preset station buttons (1 – 6) for more than 2 seconds until a beep tone is heard. The number of the pressed preset station button is displayed. ST 3 4 Repeat steps 2 and 3 to preset other stations.
Automatic Presetting The automatic presetting function is used to automatically preset up to 6 stations for each band. 1 Press BAND to select the band. 2 Press and hold A.M down for more than 2 seconds until a beep tone is heard. The scanning starts from the currently displayed frequency to higher frequencies and stops when 6 stations have been preset or the receivable frequencies have been scanned once. Note • The presetting is not performed if there is no station to be tuned in.
CD PLAYBACK Press any button (except %) to turn on the unit. 1 Insert a disc with the labeled side up to start playback. If a disc is already inserted, press FUNC to select the CD operation. DISC indicator lights up, and the track number and elapsed playing time are displayed. 2 Adjust the volume with + or - . Press these buttons to operate CD playback. Press z e EN 12 To Load or eject a disc. Pause play. The track number and elapsed playing time flash on and off. To resume play, press e again.
Note Repeat Play • The disc is neither inserted nor ejected when the unit is not turned on. • Smaller 3-inch (8 cm) CDs can not be played on this unit. And do not use an adaptor as it may cause malfunctioning. • The playback starts from the first track on the disc only when inserting a disc. In other cases (when switching from the radio operation or turning on the unit), the playback starts from the beginning of the track being played when the playback has stopped.
PROGRAM PLAY Up to 10 tracks can be set in the program memory in any order. 1 Press PROG. PROG indicator lights up. 1 2 Select a desired track by pressing SEEKr/t until its number is displayed. DISC PROG a Track number b Program number 2 3 Press PROG to set the track in the program memory. If PROG is not pressed within 5 seconds, the program play is canceled. 4 Repeat steps 2 and 3 to set other tracks. 3 5 To start the program play, press e.
To confirm the programmed tracks Press PROG in sequence. The track and program numbers are displayed in the order of the playback. To stop the program play, press PROG again. Note • The program memory of the disc is not erased even after turning off the unit. The program memory is erased when ejecting the disc and inserting another disc. • The program play cannot be performed with the intro, repeat, or random play. SETTING THE CLOCK 1 Press any button (except %) to turn on the unit.
CD CHANGER (CDC-X20M only) 1 Press FUNC and select CMT to start playing from disc 1. The disc and track numbers are displayed. 1 2 Adjust the volume with 6/7. 2 You can play CDs with this unit by connecting the optional AIWA ADC-M35 compact disc changer. Make sure that the disc magazine loaded with the discs is inserted into the connected compact disc changer. Press following buttons to operate the connected compact disc changer.
Repeat play To skip tracks Buttons Short press* Long press t Skips to the next track Advances rapidly. Releases to resume play. r Skips back to the beginning of the current track. Reverses rapidly. Releases to resume play. * Press for less than 0.5 second. To switch to another disc 1. To start playing the previous disc in the disc magazine, press DISC K. 2. To start playing the next disc, press DISC J. The number of the disc (1 – 6) is displayed.
SPECIFICATIONS RADIO SECTION GENERAL Power Supply Voltage: FM Frequency Range: 87.5 MHz – 108 MHz Usable Sensitivity: 12.7dBf 50 dB Quieting Sensitivity: 17.2 dBf IF Rejection: 80 dB Frequency Response: 30 Hz – 15,000 Hz S/N Ratio: 63 dB Stereo Separation: 35 dB at 1 kHz Alternate Channel Selectivity: 70 dB Capture Ratio: 3 dB 14.4 V (11 to 16 V allowable), DC, negative ground Load Impedance: 4Ω Tone Control: Bass ± 10 dB at 100 Hz Treble ± 10 dB at 10 kHz Pre-amp Output Voltage: 1.2 V (max.
TROUBLESHOOTING In the following cases, the corresponding error code indicator is displayed. Internal CD player: Error code Cause Solution E--2, E--3, E--6, E--8 The disc is not inserted or ejected properly. Press RESET and insert the disc again. E--4, E--5, E--7 The disc cannot be read properly. The disc may be damaged or dirty. Insert another disc. E--9 The ambient temperature is too high. Allow the unit to cool off (by moving the car out of direct sunlight, etc.).
87-KC1-901-01 970317ATM-OX Printed in Korea A
