I NSTRUCTION MANUAL AIR 66 www.aivituvin.
NOTICE Please retain these instructions for future Firmly secure all bolts,screws and knobs before use. Reconfirm that all bolts,screws,and knobs are secure every 90 days. Fasten screws loosely during initial assembly. Do not fully tighten screws until the item is completely assembled. Do not use or store this item in the proximity of open flame or flammable/combustible chemicals. Be aware that some parts are heavy and have sharp edges. Be aware that moving parts can injure,crush and cut.
TOOLS REQUIRED PHILLIPS SCREWDRIVER DRILL (RECOMMENDED) 2PERSON ASSEMBLY APPROXIMATELY 60MIN. ASSEMBLY HARDWARE M6.0x50 mm BOLT 8PCS+1 spare M3.5x60 mm SCREW 14PCS+1 spare P1 M3.5x40 mm SCREW 8PCS+1 spare P2 M3.5x35 mm SCREW 14PCS+1 spare P3 M3.5x30 mm SCREW 16PCS+1 spare P4 M3.5x25 mm SCREW 22PCS+1 spare P5 P6 P5 P6 Lock M3.
HARDWARE Spring latch Waterproof PVC 1PC 4PCS P5 P9 03 P10
PARTS CARTON 1/2 Support Shelf of Bottom Ramp Folding of Wire Pen 1PC 1PC A B Connect Bar Tray 2PCS 1PC F Ramp 2PCS H Folding of Wooden Coop 1PC E D Perch Divider 3PCS 2PCS I N PVC waterproof strip 2PCS Q 04
PARTS CARTON 2/2 Panel of Nesting Box 2PCS Panel of Nesting Box 2PCS J Bottom Floor of Nesting Box L M K 2PCS Roof of Nesting Box Roof of Coop Cap Support 2PCS 2PCS 2PCS 1PC O R P Support Panel of Middle Ramp Support of Tray 1PC 1PC G 05 Side Panel of Nesting Box 2PCS Hardware bag S C
PRODUCT ASSEMBLY 01 ①Expand the part of wire pen Part A . ② Attach the Part C to the Part B by 2XP5 screws. ③Attach the Part B to the left side of wire pen by 6XP6 screws.
PRODUCT ASSEMBLY 02 ① Attach the support bar Part S to the corner of front and left side panel by 2X P5 screws. ② Attach the ramp Part D to the Part B by 4XP7 screws. (Notice the direction of ramp) D P7 X4 P5 X2 Front S 03 ①Expand the part of wooden coop Part E. ②Attach the connect bar Part F to the left & right side of coop by 12XP5 screws.
PRODUCT ASSEMBLY 04 Connect the wooden coop and wire pen with connecting bar by 2XP2 screws each side. P2 X2 P2 X2 05 Front ①Slide in tray Part H in front. ②Slide in support panel of middle ramp Part G in back.
PRODUCT ASSEMBLY 06 ① Attach the Part G to side panel by 1 X P2 each sides. ② Attach the ramp Part D to the support panel of middle ramp Part G by 4XP7 screws. (Notice the direction of ramp) D P7 X4 P2 X2 07 Insert 3PCS perches Part I into the slots inside left and right side panel of coop by 6XP4 screws.
PRODUCT ASSEMBLY 08 Attach the nesting box,attach the Part K & Part J to the coop by 4XP1 bolts each sides. (Notice the direction of Part K & Part J ) K P1 X4 J J P1 X4 09 K Attach the side panel Part L to the Part K & Part J by 4XP3 screws each sides.
PRODUCT ASSEMBLY 10 ① Drop in the bottom floor Part M to the nesting box each sides. ② Insert the divider Part N into the slots of bottom floor each sides. N M N M 11 Attach the nesting box roof Part O to coop by 4XP7 screws each sides.
PRODUCT ASSEMBLY 12 Attach the coop roof Part P by 8XP4 screws. Px2 P4 X8 13 ①Attached PVC Waterproof Strip Part Q to the nesting box by 4XP6 screws each sides. ② Put the Waterproof pvc P10 in the connection position of 2 roof cap to avoid the water leakage.
PRODUCT ASSEMBLY 14 ①Attach the latch P8 to the front tray by 6xP7 screws ②Attach the spring latch P9 to the two front doors by 2xP7 screws each latches. (Notice the direction of latch) P9 X1 P7 X6 P7 X2 P8 X1 P9 X1 P7 X2 15 Attach the spring latch P9 to the two back doors by 2xP7 screws each latches.
Notice Read Before Assemble! The below steps are for chicken coop & run combination by 4xP2 screws each sides. If you do only buy one chicken coop ,pls ignore the following.
WARNING Manufacturer and seller expressly disclaim any and all liability for personal injury,property damage or loss,whether direct,indirect,or incidental,resulting from the incorrect attachment,improper use,inadequate miantenance,or neglect of this
