I NSTRUCTION MANUAL AIR 59 www.aivituvin.
NOTICE Please retain these instructions for future Firmly secure all bolts,screws and knobs before use. Reconfirm that all bolts,screws,and knobs are secure every 90 days. Fasten screws loosely during initial assembly. Do not fully tighten screws until the item is completely assembled. Do not use or store this item in the proximity of open flame or flammable/combustible chemicals. Be aware that some parts are heavy and have sharp edges. Be aware that moving parts can injure,crush and cut.
TOOLS REQUIRED PHILLIPS SCREWDRIVER DRILL (RECOMMENDED) 2PERSON ASSEMBLY APPROXIMATELY 60MIN. ASSEMBLY HARDWARE M6.0x55 mm BOLT 8PCS+1 spare M3.5x60 mm SCREW 20PCS+1 spare P1 M3.5x40 mm SCREW 16PCS+1 spare P2 M3.5x35 mm SCREW 12PCS+1 spare P3 M3.5x25 mm SCREW 8PCS+1 spare P4 M3.0x16 mm SCREW 6PCS+1 spare P5 P6 P5 Lock 1PC P6 M3.
03
PARTS Upper panel-front and back Side panel Tray 2PCS 2PCS 1PC A B C Perch Side panel of nesting box Side panel of nesting box 3PCS 2PCS 2PCS D E F Front panel of nesting box Bottom of nesting box Divider 2PCS 2PCS 2PCS G H I 04
PARTS Roof of nesting box Roof PVC Waterproof Strip 2PCS 2PCS 2PCS J Roof cap Down panel- front and back 2PCS 2PCS M 05 K N L
PRODUCT ASSEMBLY 01 Attach Part A & N to the side panel Part B by 16XP2 screws, then connect the Part A & N by 2XP8 screws.
PRODUCT ASSEMBLY 02 Slide in the metal tray Part C. C 03 07 Insert the perches 3xPart D into the slots inside the front and back panel of coop.
PRODUCT ASSEMBLY 04 Attach the side panels of nesting box Part E & F to the left side of coop by bolt 4xP1. E P1 X4 05 F Attach the side panels of nesting box Part E & F to the right side of coop by bolt 4xP1.
PRODUCT ASSEMBLY 06 Attached the front panel of nesting box Part G by 4xP3 screws each side. . G P1 P3 X4 P1 P3 X4 G 07 ① Drop in the bottom panel of nesting box Part H. ② Slide in the divider Part I each side.
PRODUCT ASSEMBLY 08 ① Attach the roof of nesting box 2xPart J to the nesting box by 4XP5 screws each side. ② Make sure the lock is functioning properly before locking the roof. P5 X4 J P5 X4 J 09 Attach the coop roof 2xPart K to the coop by 8XP3 screws.
PRODUCT ASSEMBLY 10 Attach PVC Waterproof Strip 2xPart L to the nesting box by 4XP4 screws each side.
PRODUCT ASSEMBLY 11 ① Attach the roof cap Part M by 4XP4 screws. ② Attach lock P7 to the tray by 6xP6.
Notice Read Before Assemble! Pls ignore the following for only one coop owner ! 13
PRODUCT ASSEMBLY 12 Attach the run to the coop by 2xP2 screws. P2 X2 13 Attach the run to the coop by 2xP2 screws.
WARNING Manufacturer and seller expressly disclaim any and all liability for personal injury,property damage or loss,whether direct,indirect,or incidental,resulting from the incorrect attachment,improper use,inadequate miantenance,or neglect of this
