INSTRUCTION MANUAL AIR 56 www.aivituvin.
NOTICE Please retain these instructions for future reference. Firmly secure all bolts,screws and knobs before use. Reconfirm that all bolts,screws,and knobs are secure every 90 days. Fasten screws loosely during initial assembly. Do not fully tighten screws until the item is completely assembled. Do not use or store this item in the proximity of open flame or flammable/combustible chemicals. Be aware that some parts are heavy and have sharp edges. Be aware that moving parts can injure,crush and cut.
TOOLS REQUIRED PHILLIPS SCREWDRIVER DRILL (RECOMMENDED) 2PERSON ASSEMBLY APPROXIMATELY 45MIN. ASSEMBLY HARDWARE M3.5x40mm SCREW 28PCS+1 spare M3.5x60mm SCREW 6PCS+1 spare P1 M3.5x30mm SCREW 6PCS+1spare P2 M3.5x25mm SCREW 40PCS+1 spare P3 M3.
PARTS Front Panel-Upper 2PCS Back Panel-Upper Front/Back Panel-Lower 2PCS 2PCS A Side Panel-Upper 2PCS B Right Side Panel 1PC Left Side Panel 1PC D C F E Roof Tray Bottom Panel 1PC 1PC 2PCS G 03 H I
PARTS Middle Panel 2PCS Upper Panel-K Upper Panel-L 1PC 1PC J K Fence Ramp 2PCS 3PCS L Front panel of small house 2PCS O M N Back panel of small house Side panel of small house Roof of small house 2PCS 4PCS 2PCS P Q R 04
PARTS Casters Casters with brake 2PCS 2PCS S 05 T
PRODUCT ASSEMBLY 01 Attach Part Q, Part P and Part O by 8xP4 screws. P Q O Q P4 X8 02 Attach the top panel Part R by 4XP4 screws. Repeat Step 1&2 to complete the other small houses.
PRODUCT ASSEMBLY 03 ① Attach the left side panel Part D with Part E by 1XP1 screw. ② Attach the right side panel Part D with Part F by 1XP1 screw. D P1 X2 D E 04 F ① Attach Part C and Part Bx2 pieces to the side panel by 12XP2 screws. ② Screw Part B by 2XP1.
PRODUCT ASSEMBLY 05 Repeat Step 4 on the front view. P2 X12 06 C Ax2 Repeat Step 4 on the front view.
PRODUCT ASSEMBLY 07 Attached Part T by 8XP4 screws.
PRODUCT ASSEMBLY 08 Attached Part S by 8XP4 screws.
PRODUCT ASSEMBLY 09 Put in Part I.
PRODUCT ASSEMBLY 10 Slide in the tray.
PRODUCT ASSEMBLY 11 ①Screw the Part M to Part J from the bottom by 3XP3 screws and then put it into the cage (Please kindly note the the side with metal fram should be OUTWARDS ). ②Screw Part N to Part J by 4XP5 screws.
PRODUCT ASSEMBLY 12 ① Screw the Part M to Part J from the bottom by 3XP3 screws and then put it into the cage(Please kindly note the the side with metal fram should be INWARDS ). ② Then Screw Part N to Part J by 4XP5 screws.
PRODUCT ASSEMBLY 13 Put in the small house.
PRODUCT ASSEMBLY 14 Put in Part K & Part I.
PRODUCT ASSEMBLY 15 Screw Part N to Part K by 4XP5 screws.
PRODUCT ASSEMBLY 16 Put in the other small house and the chewing toy, bowel.
PRODUCT ASSEMBLY 17 Attached Part G by 4XP2 screws.
PRODUCT ASSEMBLY 18 Screw the latch by 4XP5 screws on each side.
PRODUCT ASSEMBLY 19 Repeat on the front view.
WARNING Manufacturer and seller expressly disclaim any and all liability for personal injury,property damage or loss,whether direct,indirect,or incidental,resulting from the incorrect attachment,improper use,inadequate miantenance,or neglect of this product.
