I NSTRUCTION MANUAL AIR 49 www.aivituvin.
NOTICE Please retain these instructions for future Firmly secure all bolts,screws and knobs before use. Reconfirm that all bolts,screws,and knobs are secure every 90 days. Fasten screws loosely during initial assembly. Do not fully tighten screws until the item is completely assembled. Do not use or store this item in the proximity of open flame or flammable/combustible chemicals. Be aware that some parts are heavy and have sharp edges. Be aware that moving parts can injure,crush and cut.
TOOLS REQUIRED PHILLIPS SCREWDRIVER DRILL (RECOMMENDED) 2PERSON ASSEMBLY APPROXIMATELY 60MIN. ASSEMBLY HARDWARE M6.0x55 mm BOLT 4PCS+1 spare M3.5x60 mm SCREW 22PCS+1 spare P1 M3.5x40 mm SCREW 28PCS+1 spare P2 M3.5x35 mm SCREW 38PCS+1 spare P3 M3.5x25 mm SCREW 8PCS+1 spare P4 M3.
PRODUCT ASSEMBLY Front Pen Nest box Front Coop 03
PARTS Front panel of coop 1PC A 1PC B C Right panel of coop-down Ventilation panel Left/Right panel of coop-upper 1PC 2PCS 2PCS D E Right panel of nest box 1PC Left panel of nest box 1PC G1 04 Left panel of coop-down Back panel of coop 1PC G2 F Bottom panel of nest box 1PC H
PARTS Front panel of nest box Slide out tray Perch 1PC 2PCS 2PCS K J I Coop roof-L Coop roof-M Roof cap 2PCS 2PCS 1PC M L N Perch Divider panel of nest box Roof panel of nest box 2PCS 2PCS 1PC O P Q 05
PARTS Front panel of pen Back panel of pen Side panel of pen 1PC 1PC 1PC R Top panel of pen PVC Waterproof Strip 1PC 1PC U 06 S V T
PRODUCT ASSEMBLY 01 Attach Part C and F by 2xP2 , repeat on Part D and F. F P2 X2 F D C P2 X2 02 Attach Part A & B to the side of the coop panel by 16xP3.
PRODUCT ASSEMBLY 03 Put in 2pcs of perch Part K and slide in 2pcs of tray Part J. Kx2 J J 04 Attach Part E to the side by 4xP3 on each.
PRODUCT ASSEMBLY 05 Attach Part G1 & G2 to Part C by 2xP1 on each side. G1 P1 X4 G2 06 ① Attach Part I by 2xP4 on each side. ② Put in the bottom panel Part H and then insert the divider panel Part P to the bottom.
PRODUCT ASSEMBLY 07 Attach Part Q by 6xP6. Q P6 X6 08 Attach P7 by 2xP6.
PRODUCT ASSEMBLY 09 Attach Part R & S to the coop by 6xP2 on each side. P2 X12 R S 10 Attach Part O to the pen panel by 2xP4 on each side.
PRODUCT ASSEMBLY 11 ① Screw P8 to Part R by 4xP6. ② Screw Part T by 2xP2. ③ Attach Part T to Part R & S by 4xP3. P3 X4 P2 X2 T P8 X1 P6 X4 12 Attach top panel of pen Part U by 14xP4.
PRODUCT ASSEMBLY 13 Attach the roof Part L & M by 16xP4. L P4 X16 M M 14 ① Attach the roof cap Part N by 4xP5. ② Screw the 4xP2 accordingly.
PRODUCT ASSEMBLY 15 Attach the Part V by 4 x p5 screws.
WARNING Manufacturer and seller expressly disclaim any and all liability for personal injury,property damage or loss,whether direct,indirect,or incidental,resulting from the incorrect attachment,improper use,inadequate miantenance,or neglect of this
