I NSTRUCTION MANUAL AIR45 www.aivituvin.
NOTICE Please retain these instructions for future Firmly secure all bolts,screws and knobs before use. Reconfirm that all bolts,screws,and knobs are secure every 90 days. Fasten screws loosely during initial assembly. Do not fully tighten screws until the item is completely assembled. Do not use or store this item in the proximity of open flame or flammable/combustible chemicals. Be aware that some parts are heavy and have sharp edges. Be aware that moving parts can injure,crush and cut.
TOOLS REQUIRED PHILLIPS SCREWDRIVER DRILL (RECOMMENDED) 2PERSON ASSEMBLY APPROXIMATELY 60MIN. ASSEMBLY HARDWARE M6.0x50 mm BOLT 8PCS+1 spare M4.0x40 mm SCREW 24PCS+1 spare P1 M3.5x60 mm SCREW 8PCS+1 spare P2 M3.5x35 mm SCREW 8PCS+1 spare P3 M3.5x25 mm SCREW 6PCS+1 spare P4 M3.
HARDWARE Lock 1PC P9 Coop Nesting box Pen 03
PARTS CARTON 1/2 Back panel 1PC Front panel 1PC A Left panel 1PC B C Right panel Tray Perch 1PC 1PC 2PCS D E F Divider of nesting box Roof of nesting box Roof of coop 2PCS 2PCS 1PC J K L 04
PARTS CARTON 2/2 Left panel of nesting box Right panel of nesting box Front panel of nesting box 2PCS 2PCS 2PCS G1 G2 Bottom of nesting box Bottom plate 2PCS 1PC Left pen panel (outside) 1PC O 05 Left pen panel (close to the hutch) 1PC M I Right pen panel (close to the hutch) 1PC H N Right pen panel (outside) 1PC P Q
PARTS Side panel of pen Roof of pen PVC Waterproof Strip 1PC 2PCS 2PCS R S T Hardware bag 06
PRODUCT ASSEMBLY 01 Attach the front & back panel Part A & B to the side panel Part C & D by 8xP2. D B P2 X8 A C 02 ① Slide in the metal tray Part E. ② Insert the perch Part F into the slots inside the front and back panel.
PRODUCT ASSEMBLY 03 Attach the side panels of nesting box Part G1 & G2 to the left side of coop by bolt 4xP1. G1 P1 X4 04 G2 Attach the side panels of nesting box Part G1 & G2 to the right side of coop by bolt 4xP1.
PRODUCT ASSEMBLY 05 Screw the side panel of nesting box to the front panel of nesting box Part H by 4xP2 each side. H P2 X4 P2 X4 H 06 ① Drop in the bottom of nesting box Part I. ② Slide in the divider Part J.
PRODUCT ASSEMBLY 07 ① Make sure the lock is functioning properly before locking the roof. ② Attach the nesting box roof Part K to the nesting box by 4xP6 each side. P6 X4 K K P6 X4 08 Attached PVC Waterproof Strip Part T to the nesting box by 3XP5 each.
PRODUCT ASSEMBLY 09 Attach the coop roof Part L to the coop by 6xP6. L P6 X6 10 Attach the lock P9 to the tray by 6XP6.
PRODUCT ASSEMBLY 11 ① Attach the roof hinge P8 to the coop by 4XP6 each side. ② Attach the pen panel Part N&O to the coop by 4XP3. P8 X1 P8 X1 P6 X4 P6 X4 O P3 X4 12 N Attach the bottom baffle Part M to the side by 4xP2.
PRODUCT ASSEMBLY 13 Attach Part P & Q by 4xP3. Q P3 X4 14 P Attach the side panel Part R to the pen by 4xP2.
PRODUCT ASSEMBLY 15 Attach the pen roof Part S to the pen by 8xP4. P4 X8 Sx2 16 Attach the latch P7 to the side by 4xP6.
WARNING Manufacturer and seller expressly disclaim any and all liability for personal injury,property damage or loss,whether direct,indirect,or incidental,resulting from the incorrect attachment,improper use,inadequate miantenance,or neglect of this