INSTRUCTION MANUAL X AIR 38 www.aivituvin.
NOTICE Please retain these instructions for future reference. Firmly secure all bolts,screws and knobs before use. Reconfirm that all bolts,screws,and knobs are secure every 90 days. Fasten screws loosely during initial assembly. Do not fully tighten screws until the item is completely assembled. Do not use or store this item in the proximity of open flame or flammable/combustible chemicals. Be aware that some parts are heavy and have sharp edges. Be aware that moving parts can injure,crush and cut.
TOOLS REQUIRED PHILLIPS SCREWDRIVER DRILL (RECOMMENDED) 2PERSON ASSEMBLY APPROXIMATELY 45MIN. ASSEMBLY HARDWARE M3.5x40mm SCREW 18PCS+1 spare M3.5x60mm SCREW 6PCS+1spare P1 P2 M3.0x16mm SCREW 14PCS+1 spare M3.5x25mm SCREW 36PCS+1 spare P3 P4 Bowl 1PC Chewing Toy for Gift 1PC P6 P5 M3.
PARTS Front panel of small house Back panel of small house Side panels of small 1PC 1PC 2PCS A B C Top panel of small housel Front Panel-Upper Back Panel-Upper 1PC 1PC 1PC E D Layer 4PCS Right Panel-Upper 1PC Left Panel-Upper 1PC G H I
PARTS Fence Ramp Front Panel-Lower 4PCS 4PCS 1PC K Right Panel-Lower Left Panel-Lower 1PC Back Panel-Lower 1PC M L 1PC O N Caster Caster with brake Layer 2PCS 2PCS 1PC P Q R
PARTS Bottom Layer Roof 1PC Tray 1PC 1PC S U V 05
PRODUCT ASSEMBLY 01 Attach the small house,attach the Part A,B,C & D by 12XP3 screws. C B D A C 3 X8 02 3 X4 Attach upper parts,attach the Part E, F,G & H by 8xP2 screws.
PRODUCT ASSEMBLY 03 ① Screw the fence Part J to layer Part I from the bottom by 2xP3 screws each piece. (Pls pay attention to the position of Part J of 2 layers). ② Put the Part I inside house. I J 3 X4 J I 04 Attach the ramp Part K to layer by 2XP4screws.
PRODUCT ASSEMBLY 05 ① Attach lower parts,attach the Part L, M, N & O by 10XP2 screws. ② Attached the caster 2x Part P by 8XP3 screws. M O 2 X 10 Px2 P3 X8 N 06 L Attached the Caster with brake 2x Part Q by 8XP3 screws.
PRODUCT ASSEMBLY 7 ① Screw the fence Part J to layer Part I from the bottom by 2XP3 screws each piece. (Pls pay attention to the position of Part J of 2 layers) ② Put the Part I & R inside house. I R 2 J J 3 X4 I 08 Attach the ramp 2x Part K to layer by 2XP4 screws each piece.
PRODUCT ASSEMBLY 09 Attach the upper part and lower part by 6XP1 screws. (Pls pay attention the position of the upper and lower) 1 X6 E L 10 Attach the ramp Part K to layer by 2XP4 screws .
PRODUCT ASSEMBLY 11 Attached the roof Part S by 6XP8 screws. S 8 X6 12 Put in the bottom layer Part U.
PRODUCT ASSEMBLY 13 Put in the tray Part V above the bottom layer. V 14 Put in the small house,P5 & P6 inside the hutch anywhere you want.
PRODUCT ASSEMBLY 15 Screw the latch P7 by 4XP4 screws on roof and tray position.
WARNING Manufacturer and seller expressly disclaim any and all liability for personal injury,property damage or lo ss,whe ther direct ,indir ect,or incid ental ,resul ting f rom th e inc orrect attachment,improper use,inadequate miantenance,or neglect of this product.
