INSTRUCTION MANUAL X AIR 19 www.aivituvin.
NOTICE Please retain these instructions for future reference. Firmly secure all bolts,screws and knobs before use. Reconfirm that all bolts,screws,and knobs are secure every 90 days. Fasten screws loosely during initial assembly. Do not fully tighten screws until the item is completely assembled. Do not use or store this item in the proximity of open flame or flammable/combustible chemicals. Be aware that some parts are heavy and have sharp edges. Be aware that moving parts can injure,crush and cut.
TOOLS REQUIRED PHILLIPS SCREWDRIVER DRILL (RECOMMENDED) 2PERSON ASSEMBLY APPROXIMATELY 45MIN. ASSEMBLY HARDWARE M3.5x45mm SCREW 20PCS+1spare M3.5x50mm SCREW 4PCS+1spare P1 P2 M3.5x30mm SCREW 4PCS+1spare M3.5x35mm SCREW 8PCS+1spare P3 M3.0x16mm SCREW 4PCS+1spare P4 M3.
HARDWARE M3.0x16mm SCREW 4PCS+1spare M4.
PARTS Back panel Front down panel 1PC Front UP panel 1PC A Left panel 1PC 1PC B Front panel of pen Right panel 1PC D C 1PC F E Back panel of pen Side panel of pen Top panel of pen 1PC 1PC 1PC G H I 04
PARTS Metal ramp supporting 1PC Roof cap Asphalt roofs 1PC 2PCS J Ramp 1PC K Casters without brakes 4PCS P 05 Pen tray Upper hutch tray 1PC M L 1PC O N Folding metal feeder Casters with brakes 2PCS 1PC Q R
PARTS Bottom hutch tray 1PC S 06
PRODUCT ASSEMBLY 01 ① Attach front panel Part A, B & back panel Part C to the right panel Part E by 4xP2 one side and 2xP2 the other side. ② Notice there are predrill screws holes to direct. C A E B P2 X 6 02 ① Attach left panel Part D to step 1 by 2xP2 one side and 4xP2 the other side. ② Notice there are predrill screws holes to direct.
PRODUCT ASSEMBLY 03 Screw the ramp Part M to the right panel by 4xP5. P5 X4 M 04 ① Attach the side pen! ② Screw the Part H to the Part F & Part G by 2xP2 each side.
PRODUCT ASSEMBLY 05 Screw the metal ramp supporting board Part J inside the back panel of pen Part G by 2xP9. J P9 X2 06 Attach the pen to the wood hutch by screwing 2xP1 each side.
PRODUCT ASSEMBLY 07 Slide in the Upper tray N and bottom tray S, pen tray O. N O S 08 ① Screw the metal feeder Part R to the back panel by 2xP6. ② Put the chewing toy Part P7 into the cage anywhere you want.
PRODUCT ASSEMBLY 09 Attach the top panel of pen Part I by 4xP2 screws. P2 X4 10 ① Screw the asphalt roofs Part L to the hutch by 8xP3. ② Notice to level up the roof line.
PRODUCT ASSEMBLY 11 Screw the roof cap Part K to the roof by 4xP4. P4 X4 K 12 ① Attach top panel of pen and side panel of pen with 1xP8 by 4xP10 screws. ② Screw two brake casters Part Q to the 2 back legs, and one caster without brake Part P to the middle leg.
PRODUCT ASSEMBLY 13 Screw the 3 casters without brakes Part P to the front 3 legs.
WARNING Manufacturer and seller expressly disclaim any and all liability for personal injury,property damage or loss,whether direct,indirect,or incidental,resulting from the incorrect attachment,improper use,inadequate miantenance,or neglect of this product.
