This equipment has been tested and found to comply with the regulations for a Class B Analog Device, pursuant to section 15 of the FCO Rules. This equipment is designed ta provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installer and suds in accordance with the instructions, may causal harmful interference to radio communications.
RISK OF ELECTRIC BOCK DO NOT OPEN CAUTIONS OO NOT REMOVE THE COVER REDUCING THE RINK OF ELECTRIC SHOCK. ND USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: Do not expose this product to rain or a damp environment as this may create a risk of gite or electric shock as well as cause damage to this product. IMPORTANT SAFETY INSTRUCTIONS 1. Plead the Instructions: All the safety and operating instructions should be read before the product is operated. 2.
Accessories: Doting place this product on an unstable cart, stand, tripod, bracket, dr table, The product may fall, causing serious injury to a child or adult and serious damage to the product. Uses only : with a cant, stand, tripod, bracket, or table recommended by the { manufacturer, or sold with the product. Any mounting of the product ! should fallow thd manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. A product and combination should be moved with care.
«ses 18. |$the power-supply cord of ply is damaged. If liquid has been gpiliad/upon, or objects have fallen into, the product, lithe product has Been exposed to rain or water, It the product does not operate normally when following the operating instructions, Adjust only those controls that are covered by the operating recursions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restores the product to its normal operation.
#4 PART 1: introduction to the Video Sender ~—rsmmmtrre A. Applications B. Features 4 PART 2: List Packaged Contents mon A. One Transmitter B. One Receiver —C. Twa power adapters D. Two Audiovisual (A/V) cables E. OC out Power Line WWW KOR ® PART 3: Controls and Features ® PAT 4: Installation 6 # PART 5: Connecting the Transmitter to the A/V sources me A. How to sand Audio/Video from your Satellite Calvert or Laser Disc Player 7 B. How to sand Audiovisual from your VOR or DVD 8 C.
interrogation to the Video Sender Video Sonic applies advanced 2.4GHz BF wireless technology to offer users the ability to link all kinds of Audio and Video sources to TVs, Monitors, and Personal Computers without wires or cables. The Video Sender is easy to completely install within minutes, This plug-and play feature helps you to expand your freedom in your home entertainment and enhance your home security.
Dat ba in oni Liston Contents The following devices should be included in the box. Please check that you have them all before installation, A. One Transmitter (AWV101 TX) The Transmitter shirts Audio and Video signals over a 2.4GHz radio frequency carrier. B. One Receiver (AWV101 RX) The Receiver receives 2.4GHz wireless Audio and Video signals farm the Transmitter. C. Two power adapters These power adapters supply 12V DC power to the Transmitter and the Receiver.
0. Two Audio/Video [A/V] cables These two cables dre used to connect the Transmitter or the Receiver to your AV devices, RCA-1-RCA RCA-to-SCAR Transmitter: connect the Transmitter to your 47V source Receiver: connect the Receiver w your TV. Monitor or other ASV source.
Controls and Features The Transmitter and the Receiver ok alike. You can distinguish them through the logo on the units. The 2.4 Ghz dipole antenna can be rotated over an angular range of | about 300 degrees. {Do net force it tb rotate beyond its angular range limits otherwise it will pee permanent damage to both antenna and mechanical stopper. free 1. Right Audio jack (rid) 2. Left Audio jack (white) 3. Video jack (yellow 4, Dipole antenna 8. Channel select 8.
installation Setting up the Video Sender is extremely easy. It takes only a few minutes to connect the Transmitter to the A/V sources you want to view or hear at anther concoction, and then connect the Receiver to the TV set, monitors and speakers located at your site. Turning on the power switches of the Transmitter and the Receiver, you are ready 10 enjoy the A/V signals via wireless technology.
Before connecting the Video Sander Transmitter, make sure the ON/OFF switch is in the OFF position, Conn act one set of A/V cables to the A/V jacks of the Transmitter and the A/V jacks on the AV output of the A/V sources. There are three colors for the connectors of the A/V cables. Make sure tHe yellow, white and rad plugs match the yellow, white and red jacks gn both the Transmitter and the A/V sources.
; {3} COAXIAL CABLE Commendation method for dual-output components 8. How to sand Audio { Video from your VOR ar DVD 1. Connect the colloidal IN, CATV IN or VHF/UHF IN on your VCR to the TV antenna, coaxial QUT of tha TV Set-top Box or the CATV coaxial outlet, | 2. Use A/V cable connect A/V QUT from your VCR the Transmitter; Be sure to match Audi (REL) and Video jacks on both VCR ang Transmitter correctly, 3. Plug the DC adapter into a wall AC power line cutie, 4.
C. How to connection Transmitter to your Camcorder 1. Use A/V cabin to connect A/V OUT on your camcorder the Transmitter, 2. Plug the OC adapter into a wall AC prows line outlet. ~~ (2) To wall outlet | 7 worrier & D. How to send Audio from your CD Player or Cassette Deck 1. Use A/V cable to connect A/V OUT on your CD Player or Cassette Desk the Transmitter, 2. Plug the DC adapter into a wall AC power line outlet.
Before connecting the Video Receiver, make sure the ON/OFF switch absinthe OFF position. Connect one set of A/V cables to the A/V jacks of the Receiver bandit the A/V jacks on the A/V input of the A/V Display Units. There are their colors for the connectors of A/C cables. Make sure the yellow, white and red plugs match the yellow, white and red jacks on both the transmitter and the A/V sources correctly.
A. How to connect the Ascella to your TV 1. Use AV cable to connect A/V DUT from the Receiver your TV, Be sure to match Audio (REL) and Video jacks on both the Receiver and TV correctly, 2. Plug the DC adapter into a wall A/C power line outlet, (2) To wall outlet {1 000 oQ0 4 B. How to receive Ali to on a Remote Speaker 1. Uses A/V cable to connect A/V OUT on the Receiver your speaker. Be sure to match Audio (R&L) and Video jacks on both tha Relevance and TV correctly. 2.
Trusteeship Shooting Please read this use mans! carefully before using the Video Sender, if you have any difficulty using the Video Sender, consult the following checklist, which will guide you in solving most common problems. A. No picture or 4 1. Check the audio and video sources (TV, VOR, LD Player, Satellite R af, got) 2. Make sure all sables are connected correctly, 3. Make sure channelize! selections on the Transmitter and Receiver match each other. B. Interruption in image and sound 1.
