HANDS-FREE BLUETOOTH CONTROLLER for SMART READY TABLETS AND COMPUTERS Operating Manual
CONTENTS Before Turning on Your PED ..................................................4 Power .......................................................................................5 ON .......................................................................................5 OFF......................................................................................5 Modes ......................................................................................6 Changing the MODE ..................................
Thank you for purchasing the AirTurn PED handsfree, Bluetooth foot controller. We hope you enjoy many years of use from it. From page turning, to effects management and presentation control, the PED provides a myriad of uses. BEFORE TURNING ON YOUR PED The PED works with most Bluetooth SMART READY devices. This includes iPad 3 and later, iPhone 4S and later, and most devices running Android 4.3 or later with Bluetooth 4. Check out the Bluetooth Sig site for a complete list: http://www.bluetooth.
POWER ON - Press and hold the Power Button on for one second and the LED’s flash. The blue LED will begin to blink 2 times per second until pairing is started. OFF - Press and hold the Power Button on the PED until the red and blue LEDs turn off.
MODES There are six modes available on your PED. Each mode sends a different signal for each pedal. The PED is set to MODE 2 by default. MODE 1: PED-APP-Direct. (Apple iOS only). Please check with the AirTurn website for more information on app availability: http://airturn.com/ped-app-direct MODE 2: Up/Down Arrow. Left pedal = Up Arrow. Right pedal = Down Arrow. This is the most common MODE for all iOS and Android APPS. MODE 3: Left/Right Arrow. Left pedal = Left Arrow. Right pedal = Right Arrow.
Note: Holding down the pedal in any MODE for more than two seconds will repeat the key action until released. CHANGING THE MODE 1. Turn on the PED. 2. Press and hold the MODE button. The red LED will flash once per second from 1 to 6 flashes. The number of flashes corresponds to the same MODE number. Be sure to count the flashes. 3. Release the MODE button following the number of flashes that reflects the desired MODE.
PAIRING IN PED-APP-DIRECT MODE 1 Note: This MODE is for PED-APP-Direct apps only. 1. 2. 3. 4. 5. Power on the PED. Be sure the PED is in MODE 1. Go to your app and find the Bluetooth setup screen. Find the PED in the device list and tap on it. Tap on the Pair option in the dialog box. PAIRING IN MODE 2-6 Open your computer’s Bluetooth Setup dialog: iOS – Select Settings>Bluetooth and turn on the Bluetooth if it is off. When the PED is discovered, it will appear in the list of devices.
When the PED connects, the blue LED will blink 3 times per second. Once paired, the blue LED will blink 1 time every three seconds. IMPORTANT: Do not try to connect in MODE 1 and any other MODE at the same time. MODE 1 only works in PEDAPP-Direct MODE and MODES 2-6 only work when connected directly through the operating system setup. You must reset pairing to switch modes. If you choose MODE conflicting apps in iOS, it is recommended to use MODE 2 for both apps.
the PED will power down automatically. The timer is reset when any button is pressed. The PED averages a usage of 2μA when turned off and averages a usage of 5μA when turned on. VIRTUAL KEYBOARD IN IOS To turn on the virtual keyboard, put the cursor into a text box and press the Keyboard Button on the PED. Both LEDs will flash once to signify that the button has been pressed. The button will only work in Modes 2-6. Virtual keyboard support for MODE 1 is automatic. BATTERY.
FIRMWARE UPDATES/CUSTOM MODES The PED supports an update protocol called OTA, (Over the Air). Download the free AirTurn Utility app from the Apple App store. With this app, you can check and update the latest version of firmware for your PED. The PED can be programmed for many different purposes and have adjustments made for repeat delays and key repeat rates. It is possible to have complex macros and almost any key or key combination can be set up for your PED.
CARE OF YOUR PED Use a mild detergent or soap-based cleaner to remove dirt and stains from your PED. Be careful not to use sharp tools or extreme pressure on the pedal area as this will reduce the life of the membrane switches. • Do not get the PED wet or place in direct sunlight for extended periods of time. • Do not open the unit other than to replace the battery, as there are no user serviceable parts. • Do not put in trash. Please recycle. WARRANTY AirTurn, Inc.
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO ONE YEAR FROM THE DATE OF THE PURCHASE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. The warranties described herein shall be the sole and exclusive warranties granted by AirTurn and shall be the sole and exclusive remedy available to the purchaser.
(2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
RECYCLING AND DISPOSAL Electronic components and construction comply with RoHS standards. Packaging is recyclable. Please recycle. Contains Lithium Ion Battery. Battery should be disposed of according to local law. AirTurn will recycle batteries for you if returned. Please request an RMA from the support desk: support@airturn.com TRADEMARKS iPhone, iPod, iOS, iPad are trademarks of Apple, Inc. Android is a trademark of Google, Inc.
PO Box 3359 Nederland, CO 80466 support@airturn.com www.airturn.
