ATS58-2020 5.8GHz Motion sensor ATS58-2020 5.8GHz Microwave Motion sensor Version: 1.0 FCC ID: 2AVK2-ATS58-2020 Made in China This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions (1)this device may not cause harmful interference,and (2)this device must accept any interference received,including interference that may cause undesired operation Version 1.
ATS58-2020 5.8GHz Motion sensor Contents ATS58-2020 5.8GHz User Guide............................................................................................................... 3 Description............................................................................................................................................... 3 Radar Sensor illustration...................................................................................................................3 Input and Output Interface...
ATS58-2020 5.8GHz Motion sensor ATS58-2020 5.8GHz User Guide Description ATS58-2020 is a miniaturized 5.8G radar sensor launched by AirTouch，The module size is 20*20mm, the size is equivalent to a coin,The sensor uses a self-developed radar sensor chip AT5810S, which integrates a 5.8G microwave circuit, an intermediate frequency amplifier circuit and a signal processor，The chip has a high degree of integration and good production consistency.
ATS58-2020 5.8GHz Motion sensor OUT TX RX Version 1.
ATS58-2020 5.8GHz Motion sensor Module size and Pin position Figure 2 below is the schematic diagram of module size and pin position. The length and width of the module is 20 mm * 20 mm. By default, there is no pin, and the overall thickness is 2.5 mm. If a pin is required, the default pin height is 12 mm. Figure 2 Module size and pin position of ATS58-2020 Electrical characteristics Parameters Frequency TX Power Input VCC Output High LevelLow Output Level Current Min. 5725 4.
ATS58-2020 5.8GHz Motion sensor The delay time and detection area Ats58-2020 requires three pins by default, VCC, GND and out. the delay time and sensing distance are fixed values. If you need to adjust the delay time and sensing distance and other related parameters, you need to add two pins, RX and TX, as shown in Figure 3。 In terms of software configuration, RX and TX can be used as I / O ports or UART ports to adjust module parameters.
ATS58-2020 5.8GHz Motion sensor Power on Sequence The module has a power-on self-test function, that is, after the module is powered on, the out pin outputs the high level first, the low level is output after the delay of 1s, and the low level is delayed for 1s before entering the normal induction mode. The following is the sequence diagram of the control signal after the module is powered on： vcc OUT 1S 1S With inductive out = 1, without inductive out = 0 Figure5 Power on Sequence Version 1.
ATS58-2020 5.8GHz Motion sensor Detection Pattern The sensing sensitivity of radar sensor can be configured by MCU, and its limit sensing distance is 10 meters. The actual sensing distance can be adjusted according to the needs. The following is the schematic diagram of radar detection range in case of high hanging. If the sensitivity is set higher, the detection range will be correspondingly larger.
ATS58-2020 5.8GHz Motion sensor Revision History Revision 1.0 Release Date 2020/03/26 Description Initial version Requirement of FCC KDB 996369 D03 for module certification: 1. List of applicable FCC rules: The module complies with FCC Part 15.249 2. Summarize the specific operational use conditions: The module has been certified for Fix, Mobile, Portable applications. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 3.
ATS58-2020 5.8GHz Motion sensor 7. Label and compliance information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ATS58-2020 5.8GHz Motion sensor 10 Information on test modes and additional testing requirements: When testing host product, the host manufacture should follow FCC KDB Publication 996369 D04 Module Integration Guide for testing the host products.The host product shall work normally, all the transmitters installed must be operating, investigate the fundamental and unwanted/spurious emissions with the modular transmitter(s) operating in a normal mode.
