Quick Start Guide

Using your mobile hotspot
Display layout and icons
1. Signal status icon
2. Network mode icon
3. Send/receive data activity arrows
4. The number of unread messages
maximum is 100
5. Battery capacity icon—if battery
capacity is lower than 25%, this
icon is red
6. Data statistics—used/total
SIM card and battery
Your Airspeed mobile hotspot comes preinstalled with a 4G LTE
SIM card.
NOTE:
when in use. Once the SIM card has been inserted into the
mobile hotspot, do not remove.
• Do not remove SIM card when the device is powered on
because this may damage the card and the device.
• Do not bend or scratch your SIM card. Avoid exposing your
SIM card to static electricity, water or dirt.
Navigating through the Airspeed mobile hotspot
Use the Menu and Power buttons to select actions displayed
at the bottom of the screen. There are 8 main menu screens in
addition to the home screen.
6
Using your mobile hotspot
Inserting and charging the battery
1. Use the thumb catch at the bottom of your Airspeed mobile
hotspot to open the battery cover and align the battery
contacts with the terminals in the battery compartment as
shown. Push the battery down until it clicks into place.
(Figure 1 and 2)
Display Layout and Icons
1 2 3 4 5 6
Description
1. Signal status icon
2. Network mode icon
3. Send/receive data activity arrows
4. Wi-Fi signal and number of access users
5. The number of unread message
maximum is 100
6. Battery capacity icon, if battery capacity
is lower than 25%, this icon is red.
7. Data statistics, used/total
SIM Card and Battery
Your Orbic Speed comes preinstalled with a 4G LTE SIM card.
Notes:
• The SIM card MUST remain in your Orbic Speed when in
use. Once the SIM card has been inserted into the Orbic
Speed, do not remove!
• DO NOT remove SIM card when the device is powered on
since this may damage the card and the device.
• Do not ben
d or scratch your SIM card. Avoid exposing your
SIM card to static electricity, water or dirt.
Navigating Through the Orbic Speed
Use the MENU and POWER button to select actions displayed at the bottom of
the screen. There are 8 main menu screens in addition to the home screen.
Removing the 4G LTE SIM Card
1.
2.
Setting up Wi-Fi connection
1.
2.
Inserting and Charging the Battery
1. Use the thumb catch at the bottom of your Orbic Speed to open
the battery cover and align the battery contacts with the terminals
in the battery compartment as shown. Push the battery down until it
clicks into place. (Figure 1 and 2)
2. Place the battery cover over the battery compartment and press it
downward until it
clicks into place. (Figure 3)
3. Your Orbic Speed comes with a charger. To charge, plug it into an
electrical outlet. Connect the USB cable to the charger and the
other end into the Orbic Speed Type-C Port. (Figure 4)
Figure 3
Figure 1 Figure 2
Figure 4
7
Back Home
Logging into the Device Management Website
1.
2.
Enter username and password and click “Login” You have the ability to modify
the password and user name and configuration.
Note:
Wifi password . See Setting up WiFi connection.
Display Layout and Icons
1 2 3 4 5 6
Description
1. Signal status icon
2. Network mode icon
3. Send/receive data activity arrows
4. Wi-Fi signal and number of access users
5. The number of unread message
maximum is 100
6. Battery capacity icon, if battery capacity
is lower than 25%, this icon is red.
7. Data statistics, used/total
SIM Card and Battery
Your Orbic Speed comes preinstalled with a 4G LTE SIM card.
Notes:
• The SIM card MUST remain in your Orbic Speed when in
use. Once the SIM card has been inserted into the Orbic
Speed, do not remove!
• DO NOT remove SIM card when the device is powered on
since this may damage the card and the device.
• Do not bend or scratch your SIM
card. Avoid exposing your
SIM card to static electricity, water or dirt.
Navigating Through the Orbic Speed
Use the MENU and POWER button to select actions displayed at the bottom of
the screen. There are 8 main menu screens in addition to the home screen.
Removing the 4G LTE SIM Card
1. Power off the Orbic Speed. Remove the battery cover and take out
the battery.
2. Gently remove the SIM card from the SIM card slot.
Setting up Wi-Fi connection
1. Press and hold the “power” button for 3 seconds until the welcome
logo is displayed on the Screen, and Wi-Fi is on.
2. Use your terminal device to search for the wireless network
connection with the WiFi’s SSID “Verizon-RC400L-CE” and cli
ck
“Connect”. Enter PASSWORD. The Password can be found by
going to the 2.4GHz WIFI info or 5GHz WIFI Info screen. The
password is displayed next to the lock icon.
Inserting and Charging the Battery
1. Use the thumb catch at the bottom of your Orbic Speed to open
the battery cover and align the battery contacts with the terminals
in the battery compartment as shown. Push the battery down until it
clicks into place. (Figure 1 and 2)
2. Place the battery cover over the battery compartment and press it
downward until it clicks into place. (Figure 3)
3. Your Orbic Speed comes with a charger. To charge, plug it into an
electrical outlet. Connect the USB cable to the c
harger and the
other end into the Orbic Speed Type-C Port. (Figure 4)
Figure 3
Figure 1 Figure 2
Figure 4
7
Back Home
Logging into the Device Management Website
1. Make sure your device is connected to the Orbic Speed via Wi-Fi.
2. Open the browser, and enter http://192.168.1.1 or http://my.jetpack in the
address bar.
Enter username and password and click “Login” You have the ability to modify
the password and user name and configuration.
Note: The default username is admin; the default password is the same as the
Wifi password . See Setting up WiFi connection.
Figure 4
2. Place the battery cover over the battery compartment and
press it downward until it clicks into place. (Figure 3)
3. Your Airspeed mobile hotspot comes with a charger. To charge,
plug it into an electrical outlet. Connect the USB cable to
the charger and the other end into the Airspeed mobile hotspot.
Type-C port. (Figure 4)
Using your mobile hotspot
5
4321