User's Manual

ManualsBrandsAirspan Networks ManualsElectronicsBase station radio MicroMAX 3.7 GHz TDD

Table Of Contents

INTRODUCTION
- Purpose
- Targeted Audience
- Referenced Documentation
- Conventions
WARNINGS AND CAUTIONS
- Human Exposure to Radio Frequencies
- Radio Interference
- Avoiding Radio Interference
- Modifications
- General
- Manufacturer's Disclaimer Statement
DECLARATION OF CONFORMITY
- European Community, Switzerland, Norway, Iceland, and Liecht
- Declaration of Conformity with Regard to the R&TTE Directive
FCC NOTICE
- Federal Communication Commission Notice
- GPS Compliance
- Maximum Output TX Power
SYSTEM OVERVIEW
- MicroMAX Frequency Ranges
- System Components
- Customer Benefits
- Architecture
- Power
- Models
INSTALLATION PREREQUISITES
- Package Contents
- Required Tools
- Radio Site Planning
  - Radio Antenna Alignment
PHYSICAL DESCRIPTION
- MicroMAX BSR
  - Physical Dimensions
  - Ports
- SDA-4S Type II
- SDA-4SDC Type II
BSDU DESCRIPTION
- Physical Dimensions
  - Ports
  - Rear Panel
GPS DESCRIPTION
- Physical Dimensions
  - Ports
AC/DC POWER CONVERTER
- Physical Dimensions
- Redundant PS Unit
MOUNTING THE BASE STATION RADIO (BSR)
- Mounting the MicroMAX
- Pole-Mounting the BSR
- Wall-Mounting the BSR (Optional)
- Installing the SDA-4S
  - Wall Mounting
MOUNTING THE BSDU
- Mounting the BSDU
  - Desktop mounting
  - Rack mounting
MOUNTING THE GPS
- Mounting the GPS
MOUNTING AC/DC POWER CONVERTER
- Mounting the AC/DC Power Converter
  - Rack mounting
- Connecting Redundant PS Unit
CABLING THE BSR
- Connecting the BSR to the SDA-4S
- SDA-4S Type II
  - Using the SDA-4S Type II
- Connecting the BSR
CONNECTING THE SDA-4S TO THE POWER SUPPLY
- Connecting the SDA-4S Type II
- Connecting the SDA-4SDC Type II
- Connecting SDA-4S to Ethernet Network
CONNECTING POWER CABLE FOR SDA-4SDC
- Power Cable Connection
  - Housing the Connectors
  - Connecting to the SDA-4SDC
CONNECTING BSDU TO AC/DC POWER CONVERTER
- Connecting BSDU to AC/DC Power Converter
- Cable Connection
CONNECTING LIGHTNING AND SURGE PROTECTOR
- PolyPhaser Wiring Diagrams
  - Lightning and Surge Protection Connection Scenarios
CONNECTING THIRD-PARTY EXTERNAL ANTENNAS
- Connecting Third Party External Antennas
- Connecting GPS Antenna to BSDU
  - Connecting the GPS
  - GPS Alignment
TRADEMARKS AND COPYRIGHTS
ENVIRONMENTAL
- Environmental Conditions
  - BSR and SDA
  - BSDU
CONTACT INFORMATION
REVISIONS
WARNINGS
- 1. Disclaimer
- 1.1 Safety Warnings
- 1.2 Important Warning Symbols
- 1.3 Important Service Information
- 1.4 UL Information
- 1.5 CE Notice
- 1.6 European Community, Switzerland, Norway, Iceland, and L
  - Declaration of Conformity with Regard to the R&TTE Directive
- 1.7 CAUTION
- 1.8 Lightning Protection
GLOSSARY

605-0000-742_MicroMAX_Hardware_Installation_Rev_H

When working with BSDU (GPS Sync)

5. Mount and ground the protector outdoors with the provided 2 x 8-32 screws according to

the fixing template illustrated below (showing distances between centers of the two

mounting holes). The unit may be mounted/grounded on a nearby plate or bulkhead panel

that is bonded to an earth-ground system.

6. Attach the protector's lid by using the four M4 x 20-mm screws. Ensure that the neoprene

gasket on the lid is not loose or out of the groove.