User's Manual

ManualsBrandsAirspan Networks ManualsElectronicsBase station radio MicroMAX 3.7 GHz TDD

Table Of Contents

INTRODUCTION
- Purpose
- Targeted Audience
- Referenced Documentation
- Conventions
WARNINGS AND CAUTIONS
- Human Exposure to Radio Frequencies
- Radio Interference
- Avoiding Radio Interference
- Modifications
- General
- Manufacturer's Disclaimer Statement
DECLARATION OF CONFORMITY
- European Community, Switzerland, Norway, Iceland, and Liecht
- Declaration of Conformity with Regard to the R&TTE Directive
FCC NOTICE
- Federal Communication Commission Notice
- GPS Compliance
- Maximum Output TX Power
SYSTEM OVERVIEW
- MicroMAX Frequency Ranges
- System Components
- Customer Benefits
- Architecture
- Power
- Models
INSTALLATION PREREQUISITES
- Package Contents
- Required Tools
- Radio Site Planning
  - Radio Antenna Alignment
PHYSICAL DESCRIPTION
- MicroMAX BSR
  - Physical Dimensions
  - Ports
- SDA-4S Type II
- SDA-4SDC Type II
BSDU DESCRIPTION
- Physical Dimensions
  - Ports
  - Rear Panel
GPS DESCRIPTION
- Physical Dimensions
  - Ports
AC/DC POWER CONVERTER
- Physical Dimensions
- Redundant PS Unit
MOUNTING THE BASE STATION RADIO (BSR)
- Mounting the MicroMAX
- Pole-Mounting the BSR
- Wall-Mounting the BSR (Optional)
- Installing the SDA-4S
  - Wall Mounting
MOUNTING THE BSDU
- Mounting the BSDU
  - Desktop mounting
  - Rack mounting
MOUNTING THE GPS
- Mounting the GPS
MOUNTING AC/DC POWER CONVERTER
- Mounting the AC/DC Power Converter
  - Rack mounting
- Connecting Redundant PS Unit
CABLING THE BSR
- Connecting the BSR to the SDA-4S
- SDA-4S Type II
  - Using the SDA-4S Type II
- Connecting the BSR
CONNECTING THE SDA-4S TO THE POWER SUPPLY
- Connecting the SDA-4S Type II
- Connecting the SDA-4SDC Type II
- Connecting SDA-4S to Ethernet Network
CONNECTING POWER CABLE FOR SDA-4SDC
- Power Cable Connection
  - Housing the Connectors
  - Connecting to the SDA-4SDC
CONNECTING BSDU TO AC/DC POWER CONVERTER
- Connecting BSDU to AC/DC Power Converter
- Cable Connection
CONNECTING LIGHTNING AND SURGE PROTECTOR
- PolyPhaser Wiring Diagrams
  - Lightning and Surge Protection Connection Scenarios
CONNECTING THIRD-PARTY EXTERNAL ANTENNAS
- Connecting Third Party External Antennas
- Connecting GPS Antenna to BSDU
  - Connecting the GPS
  - GPS Alignment
TRADEMARKS AND COPYRIGHTS
ENVIRONMENTAL
- Environmental Conditions
  - BSR and SDA
  - BSDU
CONTACT INFORMATION
REVISIONS
WARNINGS
- 1. Disclaimer
- 1.1 Safety Warnings
- 1.2 Important Warning Symbols
- 1.3 Important Service Information
- 1.4 UL Information
- 1.5 CE Notice
- 1.6 European Community, Switzerland, Norway, Iceland, and L
  - Declaration of Conformity with Regard to the R&TTE Directive
- 1.7 CAUTION
- 1.8 Lightning Protection
GLOSSARY

Mounting the Base Station Radio (BSR)

5. Attach the MicroMAX to the mounting bracket by performing the following:

a. Slide an M10-spring lock washer and then an M10-plain washer onto each M10-hex

head screw (ensure lock washer is nearest to head of screw bolt).

b. Align the mounting bracket's holes with the MicroMAX's mounting holes as displayed

below. (The mounting bracket side that provides a groove for inserting a nut must be

aligned with the MicroMAX's mounting hole that is nearest to the MicroMAX's bottom

panel.)

c. From the external sides, insert the M10-hex head screws through the mounting

bracket's holes and MicroMAX's mounting holes. Loosely fasten with the M10-hex nuts.