User's Manual

ManualsBrandsAirspan Networks ManualsElectronicsSubscriber (terminal) station

Table Of Contents

INTRODUCTION
- Purpose
- Targeted Audience
- Referenced Documentation
- Conventions
WARNINGS AND CAUTIONS
- Human Exposure to Radio Frequencies
- Radio Interference
- Avoiding Radio Interference
- Modifications
- General
- Manufacturer's Disclaimer Statement
DECLARATION OF CONFORMITY
- European Community, Switzerland, Norway, Iceland, and Liecht
- Declaration of Conformity with Regard to the R&TTE Directive
FCC INTERFERENCE STATEMENT
- Federal Communication Commission Interference Statement
- Maximum Output TX Power
SYSTEM OVERVIEW
- ProST Frequency Ranges
- Main Features
- Architecture
  - ProST Models
  - ProST Block Diagram
- ProST Protocol Stack
- Theory of Operation
INSTALLATION PREREQUISITES
- Package Contents
- Minimum PC Requirements
- Required Tools
- Radio Site Planning
PHYSICAL DESCRIPTION
- ProST Physical Description
  - Physical Dimensions
  - Port
- SDA-1 Physical Description
- SDA-4S Type II and SDA-4S/VL Type II (Optional)
- SDA-4SDC Type II (Optional DC power supply)
MOUNTING THE PROST
- Mounting the ProST
- Wall Mounting
- Pole Mounting
- SDA-4S
  - Desktop Mounting
  - Wall Mounting
NETWORK CABLING
- Connecting to IDU
  - Using the SDA-1 Type II
  - Using the SDA-4S Type II, SDA-4S/VL Type II or SDA-4S/DC Typ
- Connecting to LAN Network
CONNECTING TO POWER
- DC Power Source
- Connecting the SDA-4SDC Type II (Optional DC adapter)
- AC Power Source
  - Using SDA-1 Type II
  - Using SDA-4S Type II and SDA-4S/VL Type II
CONNECTING POWER CABLE FOR SDA-4SDC
- Power Cable Connection
  - Housing the Connectors
  - Connecting to the SDA-4SDC
CONNECTING LIGHTNING AND SURGE PROTECTOR
- PolyPhaser Wiring Diagram
  - Lightning and Surge Protection Connection Scenarios
RSSI LED PLUG ADAPTER
- Antenna Alignment using RSSI LED Plug Adapter
- LED Status
CONNECTING EXTERNAL ANTENNA
TROUBLESHOOTING
TRADEMARKS AND COPYRIGHTS
CONTACT INFORMATION
REVISIONS
WARNINGS
- 1. Disclaimer
- 1.1 Safety Warnings
- 1.2 Important Warning Symbols
- 1.3 Important Service Information
- 1.4 UL Information
- 1.5 CE Notice
- 1.6 European Community, Switzerland, Norway, Iceland, and L
  - Declaration of Conformity with Regard to the R&TTE Directive
- 1.7 CAUTION
- 1.8 Lightning Protection
GLOSSARY
INDEX

605-0000-706 ProST Installation User Guide-Rev H

4. Plug standard telephone cable(s) (with RJ 11 ends) into phone(s) and MSG jack(s).

The figures below illustrate the SDA-MSG-to-computer cable and

SDA-MSG-to-ProST (or ProST-WiFI) cable connection:

Using SDA-WiFi

Optional extension WiFi module enabling WiFi functionality to your ProST units.

Note: For pin-out refer to SDA-1 Type 2 above.

To connect the SDA-WiFi’s LAN port(s) to Ethernet network and the RJ 45 port to

ProST:

1. Plug a Category 5 Ethernet cable into one or more of the SDA-WiFi unit's 8-pin RJ-45 LAN

ports.

2. Plug the other end of the Category 5 Ethernet cable into a computer's LAN port located at

the back of the computer.

3. Plug the additional Category 5 Ethernet cable into the PSA unit 8-pin RJ-45 Radio port and

then into the ProST.

The figures below illustrate the SDA-WiFi-to-computer cable and

SDA-WiFi-to-ProST cable connection: