User's Manual

ManualsBrandsAirspan Networks ManualsElectronicsSubscriber (terminal) station

Table Of Contents

INTRODUCTION
- Purpose
- Targeted Audience
- Referenced Documentation
- Conventions
WARNINGS AND CAUTIONS
- Human Exposure to Radio Frequencies
- Radio Interference
- Avoiding Radio Interference
- Modifications
- General
- Manufacturer's Disclaimer Statement
DECLARATION OF CONFORMITY
- European Community, Switzerland, Norway, Iceland, and Liecht
- Declaration of Conformity with Regard to the R&TTE Directive
FCC INTERFERENCE STATEMENT
- Federal Communication Commission Interference Statement
- Maximum Output TX Power
SYSTEM OVERVIEW
- ProST Frequency Ranges
- Main Features
- Architecture
  - ProST Models
  - ProST Block Diagram
- ProST Protocol Stack
- Theory of Operation
INSTALLATION PREREQUISITES
- Package Contents
- Minimum PC Requirements
- Required Tools
- Radio Site Planning
PHYSICAL DESCRIPTION
- ProST Physical Description
  - Physical Dimensions
  - Port
- SDA-1 Physical Description
- SDA-4S Type II and SDA-4S/VL Type II (Optional)
- SDA-4SDC Type II (Optional DC power supply)
MOUNTING THE PROST
- Mounting the ProST
- Wall Mounting
- Pole Mounting
- SDA-4S
  - Desktop Mounting
  - Wall Mounting
NETWORK CABLING
- Connecting to IDU
  - Using the SDA-1 Type II
  - Using the SDA-4S Type II, SDA-4S/VL Type II or SDA-4S/DC Typ
- Connecting to LAN Network
CONNECTING TO POWER
- DC Power Source
- Connecting the SDA-4SDC Type II (Optional DC adapter)
- AC Power Source
  - Using SDA-1 Type II
  - Using SDA-4S Type II and SDA-4S/VL Type II
CONNECTING POWER CABLE FOR SDA-4SDC
- Power Cable Connection
  - Housing the Connectors
  - Connecting to the SDA-4SDC
CONNECTING LIGHTNING AND SURGE PROTECTOR
- PolyPhaser Wiring Diagram
  - Lightning and Surge Protection Connection Scenarios
RSSI LED PLUG ADAPTER
- Antenna Alignment using RSSI LED Plug Adapter
- LED Status
CONNECTING EXTERNAL ANTENNA
TROUBLESHOOTING
TRADEMARKS AND COPYRIGHTS
CONTACT INFORMATION
REVISIONS
WARNINGS
- 1. Disclaimer
- 1.1 Safety Warnings
- 1.2 Important Warning Symbols
- 1.3 Important Service Information
- 1.4 UL Information
- 1.5 CE Notice
- 1.6 European Community, Switzerland, Norway, Iceland, and L
  - Declaration of Conformity with Regard to the R&TTE Directive
- 1.7 CAUTION
- 1.8 Lightning Protection
GLOSSARY
INDEX

605-0000-706 ProST Installation User Guide-Rev H

on the ProST's back panel and the supplied (when ordered) pole-mounting brackets. The pole-

mounting bracket is designed to support the ProST on a round pole of 45 mm in diameter.

The figure below illustrates a summary of the ProST pole-mounting procedure.

To pole mount the ProST:

1. Attach the mounting bracket to the ProST:

a. Align the mounting bracket with the ProST's mounting holes so that the mounting

bracket's side with the built-in nut is aligned with the ProST's mounting holes furthest

from the ProST's bottom panel, as shown in the figure below.

b. Slide an M10-flat washer and M10-spring lock washer onto an M10-hex head screw

(ensure spring lock washer is closest to the bolt's head). From the external side, insert

the M10-hex head screw through the mounting bracket and ProST's mounting holes.

Fasten the M10-hex head screw (one is provided with a built-in nut while the other

requires you to insert an M10-hex nut into the ProST's mounting hole).