User Manual
Table Of Contents
- 1.1 0BPurpose
- 1.4 1BReferenced Documentation
- 2.1 2BProST Frequency Ranges
- 2.2 3BProST-2 Frequency Ranges
- 2.3 4BArchitecture
- 2.4 5BModels
- 3.1 6BPackage Contents
- 3.2 7BMinimum PC Requirements
- 3.3 8BRequired Tools
- 3.4 9BRadio Site Planning
- 4.1 10BProST Physical Description
- 4.2 11BSDA-1 Physical Description
- 4.3 12BSDA-4S Type II and SDA-4S/VL Type II (Optional)
- 4.4 13BSDA-4SDC Type II (Optional DC power supply)
- 5.1 14BWall Mounting
- 5.2 15BPole-Mounting
- 5.3 16BMounting the SDA-4S
- 6.1 17BConnecting to IDU
- 6.2 18BConnecting to LAN Network
- 7.1 19BDC Power Source
- 7.2 20BConnecting the SDA-4SDC Type II (Optional DC adapter)
- 7.3 21BAC Power Source
- 8.1 22BHousing the Connectors
- 8.2 23BConnecting to the SDA-4SDC
- 9.1 24BPolyPhaser Wiring Diagram
- 9.2 25BLightning and Surge Protection Connection Scenarios
- 10.1 26BLED Status
- 12.1 27BTroubleshooting
- 12.2 28BGlossary of Terms
- 12.3 29BRevision History
- 12.4 30BContact Information
ProST Hardware Installation User Guide
Page 46 Commercial in Confidence UWB-D00111 Rev K
6.1.2 Connecting the SDA-4S Type II, SDA-4S/VL Type II or SDA-4S/DC Type II
The SDA-4S Type II, SDA-4S/VL Type II or SDA-4S/DC Type II adapters (referred hereafter as
SDA-4S) provide one 15-pin D-type female port for interfacing with the ProST (which also
provides a 15-pin D-type female port).
The ODU-to-IDU connectivity implements a CAT 5E cable with 8-pin RJ-45 connectors at either
end. However, for allowing the use of RJ-45 connectors, your ProST kit includes two DB15-to-
RJ45 adapters that can easily be attached to the 15-pin D-type ports of the ProST and SDA-4S.
The cable setup for ProST to SDA-4S connectivity is as follows:
¾ Cable: Straight-through CAT 5E Ethernet cable
¾ Connectors:
• ProST: DB15-to-RJ45 adapter
• SDA-4S: DB15-to-RJ45 adapter
• CAT 5Ee cable with 8-pin RJ-45 male connectors on either end
¾ Connector pinouts:
Figure 34 - Pinouts ProST to SDA-4S
Note: The standard ProST/ProST-WiFi kit does not include the SDA-4S Type
II, SDA-4S/VL Type II or SDA-4S/DC adapters. For pricing and ordering of
the SDA-4S Type II, SDA-4S/VL Type II or SDA-4S/DC adapter, please
contact your nearest Airspan dealer.
To connect the ProST to the SDA-4S:
1. Attach the DB15 side of the DB15-to-RJ45 adapter to the ProST's 15-pin D-type port
(female), labeled DATA & PWR.
2. Attach the DB15 side of the second DB15-to-RJ45 adapter to the SDA-4S's 15-pin D-type
port (female).
3. Plug the RJ-45 connector, at one end of the CAT 5Ee cable (not supplied), into the RJ-45
port of the DB15-to-RJ45 adapter located at the ProST.
4. Plug the RJ-45 connector, at the other end of the CAT 5Ee cable, into the RJ-45 port of the
DB15-to-RJ45 adapter located at the SDA-4S.