User's Manual
Table Of Contents
- Installation
- Overview AS4000
- Overview AS4020
- Preparation
- Rack Installation
- AS4000 AC Rack Cabling and Wiring
- AS4000 CT Shelf Cabling and Wiring
- _
- Expansion Rack Cabling
- Setup and Test
- System Testing
- AS4000 AC Setup and Test
- Access Concentrator: Turn-Up and DC measurements
- Setting Up the Access Concentrator
- _
- Setting the TEI and Baud Rate for Netspan Connection
- Creating AC Shelf/Rack on Sitespan
- Setting up AC Rack and Shelf configuration
- Configure AC Cards
- Configure AC Shelf properties
- Check Boot Sequence
- Alarm and Status Indications (Test 3)
- Self Test (Test 4)
- Test CTU cabling to the DDF E1 Cards
- Test CTU cabling to the Distribution Frame (DDF) GR303 Cards.
- Test XTU cabling to the DDF
- Connecting the AC to the Network
- Connect E1s/T1s to the Switch or Cross-Connect at the DDF
- Access Concentrator Rack Commissioning Test Results
- AS4000 CT Setup and Test
- AS4020 CT Setup and Test
- _
- General
- Repair and Return Procedure
- Repair Charges
- Return & Repair Tag
- Packing and Shipment
- Glossary
- Index
Printed Documentation
182
Warnings and Cautions
SAFETY
1. Read and follow all warning notices and instructions marked on the product or
included in this manual
2. Do not allow anything to rest on the power cord and do not locate the product where
persons could step or walk on the power cord.
3. When installed in the final configuration, the product must comply with the applicable
Safety Standards and regulatory requirements of the country in which it is installed. If
necessary, consult with the appropriate regulatory agencies and inspection
authorities to ensure compliance.
4. No hazardous RF radiation is emitted from the equipment.
WARNING - HAZARDOUS VOLTAGES
1. On AC installations, hazardous voltages exist. Use caution when verifying or working
with AC power. Remove metal jewellery that could come into contact with AC power.
2. On DC sections, short circuiting the low voltage, low impedance circuits can cause
severe arcing that may result in burns or eye damage. Remove rings, watches etc. to
avoid shorting DC circuits.
The CE Marking on an Airspan product signifies that it has been certified according to the
EMC directive 89/336/EECand the low voltage directive 73123/EEC or the Radio &
Telecommunications Terminal Equipment Directive 1999/5/EC . The product fulfills the
requirements according to the following standards:
EN300385 for EMC
including.
EN55022 Group 1 Class A for the Central Terminal Emissions.
EN55022 Group 1 Class B for the Subscriber Terminal Emissions.
EN60950 Safety
NOTES
1. The Subscriber Terminal equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
2. Airspan products do not contain hazardous substances (as defined in UK ‘Control of
Substances Hazardous to Health Regulations 1989’, and the ‘Dangerous Substances
Regulations 1990’). At the end of any Airspan product’s life cycle, the customer
should consult with Airspan to ensure that the product is disposed of in conformance
with the relevant regulatory requirements
3. Airspan products do not contain hazardous substances (as defined in UK ‘Control of
Substances Hazardous to Health Regulations 1989’, and the ‘Dangerous Substances
Regulations 1990’). At the end of any Airspan product’s life cycle, the customer
should consult with Airspan to ensure that the product is disposed of in conformance
with the relevant regulatory requirements
CAUTION: any modifications to this device not expressly authorised by the
manufacturer could void the user's authority to operate this device.
The following products are FCC compliant:
AS4000 Central Terminal
AS4000 Access