High Performance Spatial Soundbar with Subwoofer and Bluetooth® Handbook v2 1
Contents Welcome 3 Orbitsound contact information 3 Package contents 3 The soundbar Remote control Subwoofer 4 4 4 Control panel overview 5 Getting Started 6 Connect, power on Connect the Soundbar to your TV Bluetooth AUX input Remote control 6 7 9 9 10 Advanced Setup & Use 11 Positioning - getting the most from spatial sound Subwoofer placement Other features 11 11 12 Power saving Setting memory Reset soundbar levels Auto-mute Bluetooth resume / grab 12 12 12 13 13 Important safety in
Welcome Thank you for purchasing the orbitsound M10LX spatial soundbar with compact subwoofer and Bluetooth. With proper use the orbitsound M10LX delivers superb sound fidelity, engaging spatial sound, and will provide you with a fantastic listening experience. This instruction booklet covers important safety and setup information as well as advice on how to get the most out of your orbitsound M10LX. Orbitsound contact information ORBITSOUND LTD.
The soundbar Spatial sound generators Status LEDs Status LED State RED: Standby BLUE: On OFF: Power off IR receiver The orbitsound M10LX soundbar produces most of the sound that you hear. It produces the main signal and spatial information. Remote control The remote control provides volume control, tone control and sound source selection, and additionally playback controls when using a connected Bluetooth device.
Control panel overview The soundbar can be controlled from the control panel: 6 Optical Aux Bluetooth 1 2 7 3 4 5 1. Source: Press to cycle through the inputs. This controls what device is playing through the soundbar. 2. Bluetooth: Short press to renew a Bluetooth connection / start playback. Long press (Press and hold) to enter pairing mode. 3. Vol - : Reduce volume. 4. Volume +: Increase volume. 5. Standby: Enter standby mode or power on. 6.
Getting Started Connect, power on 2 3 Spatial soundbar with subwoofer and Bluetooth ©2013 Orbitsound Ltd. Model: M10LX 2 Subwoofer Output 4 ohm minimum Only connect supplied subwoofer 1 2 1 1 Connect Subwoofer 2 Connect Power power 3 Switch on 1. Connect the subwoofer as shown (see below picture) 2. Connect power to the soundbar. 3. Switch on the power switch.
Connect the Soundbar to your TV 1) Remove plastic covers from optical cable: IMPORTANT: Remove the protective plastic covers from a new TOSLINK (optical) cable before connecting to the optical sockets. Failure to remove these covers may result in damage and will interrupt the sound output.
2) (OPTION) If your TV does not have an optical output: TV CONNECTION PANEL HDMI IN 1 DVI AUDIO IN AUDIO OUT HDMI IN 2 AUDIO IN VIDEO IN Spatial soundbar with subwoofer and Bluetooth ©2013 Orbitsound Ltd. Model: M10LX Subwoofer Output 4 ohm minimum Only connect supplied subwoofer Use the included analogue RCA/Jack cable to connect the audio output from your TV to the soundbar. Note: Some TVs may only have a 3.5mm jack output, you can also use this same cable. SImply use the 3.
Bluetooth You can connect your phone or tablet for Bluetooth playback. Optical Aux Bluetooth 1 2 3 Solid blue light: You’re paired! Slow flash blue light: Looking for previously paired device Fast flash blue light: In pairing mode 1. Press to select Bluetooth sound source. The Bluetooth source light will show the status of the Bluetooth connection. 2. To pair a new device: Press and hold the Bluetooth pairing button for 3 seconds.
Remote control The control panel functions can also be done from the remote control: Source Volume + / Power Changes the input source Controls volume Enter standby / resume Change tone: Bass and treble controls the sound: TREB BASS TREB Note: Treble changes the sound of the soundbar + / - 5 steps. Note: Bass changes the volume of the subwoofer remotely + / - 5 steps.
Advanced Setup & Use The orbitsound M10LX is easy to set up and enjoy, but even better sound may be achieved by following these guidelines. Positioning - getting the most from spatial sound The spatial sound field is produced by the speakers in the sides of the soundbar.
Other features Power saving The M10LX features a low power state. When the soundbar enters standby mode, the power consumption is reduced. It is recommended that Users routinely use standby mode to save energy. Setting memory When in standby mode, or if disconnected from the mains completely, the soundbar will remember settings for pairing, bass, treble, volume and source selection. Note that the volume will be reduced if set very high when the unit restarts to protect the listener.
Auto-mute If there is no signal, or extremely low input signal, the soundbar will enter automute mode. This reduces power consumption, and also completely silences the soundbar and subwoofer. Bluetooth resume / grab If you have previously paired your phone/tablet, there is no need to re-pair the device. Simply choose the Bluetooth source, then short press the Bluetooth button on the control panel. The soundbar will seek a previously paired device, and resume playback.
Maintenance Cleaning and care Use a soft, clean cloth moistened with plain, luke-warm water to clean the exterior of the unit. Glass cleaner is a good way to remove finger marks, but please use it sparingly, and avoid contact with the actual loudspeaker driver units. IMPORTANT: Never use solvents such as benzene or other strong chemical cleaners since these could damage the unit’s finish. It is VERY important that no liquid reaches the inside of the unit.
Troubleshooting No sound is heard • • • • • Check power connections and that there is a continuous blue light on control panel. Check that the TV or other sound source is playing and that it is connected properly to the soundbar. If unsure that your media device is playing, unplug, and test with headphones. Press the sound source button on the remote control or control panel to change the sound source. The indicators show which source is playing. Adjust the volume of the soundbar until sound is heard.
Sound is noisy / ‘hissy’ • • • Turn down the volume of the soundbar unit Turn up the output volume of music source to compensate. Use the digital optical (TOSLINK) inputs if possible to reduce noise. Digital optical issues: ‘Clicking’ or no sound • • • • Connect the TV optical output to the soundbar optical input preferentially. Ensure both ends of the optical cable have had the protective plastic tip removed.
Orbitsound Warranty This Orbitsound product is supplied with a 12 month limited manufacturer’s warranty dated from new purchase date. This warranty covers repairs or replacement that may be required in the event of unit failure during normal use, subject to the terms and conditions stated below and at the Agent’s discretion.
Orbitsound Ltd Warranty Terms and Conditions 1. RETURN TO BASE WARRANTY 5. FORCE MAJEURE Faulty products will be repaired or replaced (as deemed appropriate by the relevant Agent) at the Agent’s premises.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. type plug has two blades and a third grounding prong. The wider blade or third prong is provided for your safety. If the provided plug does not fit in your outlet, consult an electrician for replacement of the obsolete outlet. - Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Specifications Frequency range +/- 3 dB [Hz] Control; response (remote control) 38 – 16KHz +,-8dB at 100Hz and 10KHz Maximum SPL [dB] 97dBA Amp. power 250W total Crossover frequencies [Hz] 190/5,000 Tweeter drivers 1 x 1” m/c Front main drivers 4x2“ Spatial drivers 2 x 2” full-range Enclosure type Sealed/orbitsound spatial Sub-Bass driver 1 x 6.5” Sub-Bass Enclosure type Tuned reflex Connection input(s) Stereo Line level -10dBu 3.5mm jack and RCA.
