User's Manual

3
4
The statements for 5.8G module:
This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two
condions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operaon.
Changes or modificaons do not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Please noce that if the FCC idenficaon number is not visible when the module is installed
inside another device, then the outside of the device into which the module is installed must
also display a label referring to the enclosed module. This exterior label can use wording such
as the following: "Contains FCC ID: Z9G-EDF24" any similar wording that expresses the same
meaning may be used.
This equipment complies with FCC radiaon exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20cm between the radiator & your body. This transmier must not be co-located or operang
in conjuncon with any other antenna or transmier.
The module is limited to OEM installaon ONLY.
English
Important safety instrucon
The OEM integrator is responsible for ensuring that the end-user has no manual instrucon to
remove or install module.
The module is limited to installaon in mobile applicaon;
A separate approval is required for all other operang configuraons, including portable
configuraons with respect to Part 2.1093 and difference antenna configuraons.
There is requirement that the grantee provide guidance to the host manufacturer for compliance
with Part 15B requirements.
This device contains licence-exempt transmier(s)/receiver(s) that comply with Innovaon,
Science and Economic Development Canada’s licence-exempt RSS(s). Operaon is subject to the
following two condions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operaon of the device.
ISED Regulatory compliance
This device contains licence-exempt transmiers that comply with Innovaon, Science and Economic
Development Canada’s licence-exempt RSS(s).
Operaon is subject to the following two condions:
This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operaon
of the device.
L’émeeur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovaon,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L’exploitaon est autorisée aux deux condions suivantes :
L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepble
d’en compromere le fonconnement.
This equipment complies with IC RSS-102 radiaon exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with minimum distance 20cm between the
radiator and your body.
Cet équipement est conforme aux limites d'exposion aux radiaons IC CNR-102 établies pour
un environnement non contrôlé. Cetéquipement doit être installé et ulisé avec une distance
minimale de 20 cm entre le radiateur et votre corps.
FCC Regulatory Compliance
Warning: changes or modificaons not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protecon against harmful interference in a residenal installaon. This equipment generates,
uses and can radiate are designed to provide reasonable protecon against harmful interference
in a residenal installaon.
However, there is no guarantee that interference will not occur in a parcular installaon.
If this equipment does cause harmful interference to radio or television recepon, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separaon between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Compliance
This equipment complies with FCC radiaon exposure limits set forth for an uncontrolled environment.
This equipment should beinstalled and operated with minimum distance 20cm between the
radiator and your body. This transmier must not be co-located or operang in conjuncon with
any other with minimum distance 20cm between the radiator and your body. This transmier
must not be co-located or operang in conjuncon with any other antenna or transmier.
Important safety instrucon
English