User manual & installation for remote control for KRT2 Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver Revision 1.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver Revision 1.0 KRT2-RT Change history Revision Date 1 Description of change June, 6th 2010 First issue List of Service-Bulletins (SB) Service Bulletins are to be inserted into this manual and to be enlisted in the following table. SB Number Rev. Nr.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT Revision 1.0 Contents 1. General.......................................................................................................................................4 1.1. Symbols ................................................................................................................................. 4 1.2. Abbreviations ...................................................
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT Revision 1.0 1. GENERAL This manual contains information about the physical, mechanical and electrical characteristics and about installation and operation of the remote control for VHF communication transceiver KRT2. This manual is based on the current manual for the KRT2 P/N: 100(0001)-(060). 1.1.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT 1.2. Abk. Revision 1.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT 1.3. Revision 1.0 Customer service In order to facilitate a rapid handling of return shipments, please follow the instructions of the input guide for reclamations and return shipments provided at the Service-Area within the A I R p l u s W e b P o r t a l www.airplus24.com. Any suggestions for improvement of our manuals are welcome. Contact: www.airplus24.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT 2. Operation in general 2.1. Controls - overview Revision 1.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT EIN/AUS Revision 1.0 switch DUAL WATCH 1. Activates Mode for mutual monitoring of two frequencies. 2. Left cursor for name programming AUDIO selection 1. Navigation through the various basic setttings for VOL, SQ, VOX, DIM etc. press shortly 2.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT Display DUAL Meaning DUAL Watch is active [03] Favorite list index(0-99) (MEMORY) 125.100 oben Revision 1.0 remark Can be deactivated with DUAL or change of frequency [ ] selected memory in Favorite- frequency list (099) Active - Frequency 134.825 unten Standby - Frequency < The pointer indicates what the turning knob will change VOL SQ VOX…..
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT Revision 1.0 3. Operation 3.1. General The KRT2-RC and the KRT2-transceiver will be synchronized by a serial RS232-interface after any change at either side of the two devices. Approx. every 30 seconds the connection is checked an will be confirmed by showing „r“ in the upper right corner of the display.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT Revision 1.0 After the first connection confirmation on the part of KRT2 all settings are transferred from the KRT2 to KRT2-RC. 4.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT Revision 1.0 5. Installation 5.1. Notice The following hints should be considered for installation. A certified maintenance shop should perform the wiring For the wiring diagram refer to chapter 5.6.3 5.2.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT Revision 1.0 5.3. Unpacking and controlling of device Carefully unpack the equipment. Damages due to transportation must immediately be reported to the shipping company. Save the shipping container and all packing material to substantiate your claim. For storage or reshipment the original packing material should be used. 5.4.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT Revision 1.0 5.5. Connection of device The 9-pin D-Sub connector contains all electrical connections (9…33V) as well as the 3-wire RS232-connection to the KRT2transceiver. The battery plus connection must be protected with at least 1-amp slow blow fuse ! 5.6. Cabling 5.6.1.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT 5.6.3. wiring diagram Revision 1.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT Revision 1.0 5.7. check after installation A certified maintenance shop must verify the proper operation of the VHF transceiver. A complete check of all airplane systems is required to certify that the new wiring is not causing any malfunction. A test flight is recommended to verify proper transceiver operation. 5.8.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT 5.9. Drawings 5.9.1. Dimensions of the device Revision 1.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver Revision 1.0 KRT2-RT 5.9.2.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT Revision 1.0 6. Appendix 6.1. Technical Data GENERAL Admission ETSO-2C169a, ED-23B Class 4 ED-23B Class C TSO-C169a,Class 6 TSO-C169a, Class H1 & H2 Used standards EUROCAE ED-23B RTCA DO-160E RTCA DO-178B Software Level D dimensions Height: 66mm Width: 62mm Depth: 46mm plus rear panel plugs 60mm weight 0.
User manual & instruction for installation remote control for Doc.-Nr: GT-3000-810100 VHF-Communication Tranceiver KRT2-RT Revision 1.
