User`s guide

Aironet Wireless Communications, Inc. 7-51 Confidential and Proprietary
+0x001A LongRetryLimit u16 0 default 16 Long Retry Limit (see 802.11).
0 selects factory default.
+0x001C TxMSDULifetime u16
(kus)
0 default 5000 0 will select the factory default [~5 sec].
+0x001E RxMSDULifetime u16
(kus)
0 default 10000 0 will select the factory default [~10 sec]
+0x0020 Stationary u16 0 0 If set, indicates that the radio is stationary. This
information may be used to modify roaming
algorithms.
+0x0022 Ordering u16 0 0 If set, strictly ordered multicast/broadcasts are used.
+0x0024 Device Type u16 0 0 The default for the PC4500 is 0x0065.
The default for the PC4800 is 0x006D.
+0x0026 Reserved u8[10] 0’s 0 reserved for future use
SCANNING/ASSOCIATING
+0x0030 ScanMode u16 0 0 Default is active scanning
0 = Active -- default
1 = Passive
2 = Aironet Active Scanning
+0x0032 ProbeDelay u16
(kus)
0 default 3 Time to wait after switching to a channel for clear
channel assessment. 0 selects factory default. Use
0xFFFF to select 0 kus.
+0x0034 ProbeEnergyTimeout u16
(kus)
0 default 3 Time to wait for energy after an active probe.
0 selects factory default.
+0x0036 ProbeResponseTimeout u16
(kus)
0 default 20 Time to wait for a probe response after energy detected.
0 selects factory default.
+0x0038 BeaconListenTimeout u16
(kus)
0 default 40 Time to listen for a beacon on each channel.
0 selects factory default.
+0x003A IbssJoinNetTimeout u16
(kus)
0 default 10000 IBSS: Time to scan for an IBSS before forming a
network.
0 selects the factory default.
0xFFFF indicates scan until found. 1 is good enough
for starting without scanning, since chances of finding
a network in 1 kusec are virtually nil.
+0x003C AuthenticationTimeout u16
(kus)
0 default 2000 Time limit after which an authentication sequence will
be terminated/restarted.
0 selects factory default.
+0x003E AuthenticationType u16 0 default 1 (open) Selects the desired authentication and privacy methods.
0x01 = Open
0x02 = Shared-Key
0x04 = Exclude Unencrypted
Note, 0 (zero) selects no authentication and no
exclusion of unencrypted frames.
+0x0040 AssociationTimeout u16
(kus)
0 default 2000 ESS: Time limit after which an association sequence
will be terminated.
0 selects factory default.
+0x042 SpecifiedAPtimeout u16
(kus)
0 default 10000 0 selects the factory default [~10 sec].
If non-zero, associate to any AP after the timeout
interval has passed.
A value of 0xFFFF indicates that the unit should never
Associate to an AP not in the list.
Note, only applies in ESS mode and if a "valid AP-list"
has been passed down.
+0x0044 OfflineScanInterval u16
(kus)
0 0 0 disables offline scanning.
The time period between offline scans.
+0x0046 OfflineScanDuration u16
(kus)
0 0 0 disables offline scanning.
The duration of an offline scan.
+0x0048 LinkLossDelay u16
(kus)
0 0 Time to delay before reporting a loss of association
event. This may be required to prevent the driver from
being overloaded with loss/reassociation events when
the radio enters a fringe area.
A loss of association will only be reported if the
condition continues for longer than the LinkLossDelay
time.
A reassociation will always be reported (immediately)
if the access point has changed. If the radio reassociates
to the same AP before the LinkLossDelay time period
has expired, no reassociate message will be posted up
to the host.