HP-3000E 200Mbps Powerline Ethernet Adapter User’s Manual
Declaration of Conformity We, Manufacturer/Importer OvisLink Corp. 5F., NO.6, Lane 130, Min-Chuan Rd.
AirLive HP-3000E CE Declaration Statement Country cs Česky [Czech] Declaration OvisLink Corp. tímto prohlašuje, že tento AirLive HP-3000E je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. da Undertegnede OvisLink Corp. erklærer herved, Dansk [Danish] at følgende udstyr AirLive HP-3000E overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. de Hiermit erklärt OvisLink Corp.
COPYRIGHT Copyright 2005/2006 by this company. All rights reserved.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.
CONTENTS Chapter I : Introduction..................................................................................................................................... 4 1.1 Overview .................................................................................................................................... 4 1.2 Physical Details .......................................................................................................................... 4 1.2.1 LEDs ......................................
Chapter I : Introduction 1.1 Overview The 200Mbps Powerline Ethernet Adapter allows you to connect any device which has an Ethernet port to a Powerline network. In operation, the 200Mbps Powerline Ethernet Adapter is completely transparent, and simply passes data between the Ethernet port and the Powerline network. The data transfer rate can be up to 200Mbps. The 200Mbps Powerline Ethernet Adapter is a simple plug and play installation, no configuration or software setup required.
1.2.1 LEDs Power On - Normal operation. Off - No power PLC link On - The Powerline network is active. This means that at least one other Powerline device was detected. Off - Powerline network is not available - no other Powerline devices were detected. Flashing (Blue) - Received data rate via the Powerline network is bigger than 80Mbps. Flashing (Pink) - Received data rate via the Powerline network is between 80 Mbps and 50Mbps.
Chapter II : Setup Configuration requires the use of a Windows PC. Once configured, any device may be connected to the 200Mbps Powerline Ethernet Adapter's Ethernet port. To perform configuration, follow this procedure. 1. Connect a standard LAN cable from the 200Mbps Powerline Ethernet Adapter's Ethernet port to your PC. 2. Plug the 200Mbps Powerline Ethernet Adapter into a normal AC power point. 3. Wait a few seconds for startup to be completed, and then check the LEDs 4.
7. Once installation is completed, run the HP-3000E utility program. The first screen (Network Tab) will display information of the compatible devices found. Choose the desired device from the Device Selection, and the information of the selected device will be displayed in the Network Topology table.
8. The status bar on the bottom of the screen indicates the connection status of the Powerline device. Click the Encryption tab. You will see a screen like the example below. 9. Enter the desired Network Password in the field provided. Enable the Set Encryption for Remote Device and enter the Remote Device password in the DAK Password field. Click Set to save this value. If the DAK Password is left blank, the Network Key will be saved to the local Powerline device only. 10.
Setup is now complete. If your PC is not the device you wish to use with the 200Mbps Powerline Ethernet Adapter, connect the Ethernet cable from the 200Mbps Powerline Ethernet Adapter to the desired device. The 200Mbps Powerline Ethernet Adapter is now ready for use.
Chapter III : Security Button This section describes how to use Security button for configuration in the following situations: Two unassociated adapters (a,b) are forming a new network (Network AB). The procedure is as follows: 1. Press the security button on the adapter (a) for less than 3 seconds. 2. Press the security button on the adapter (b) for less than 3 seconds. 3. The Power LEDs start to flash. 4. After a few seconds, the Power and PLC link LEDs should be on.
Chapter IV : Operation If your Powerline devices have difficulty communicating with each other, check the following: Each Powerline device must use the same Network Key. You can use the Encryption tab of theHP3000E utility to assign a Network Key to other Powerline devices. 200Mbps Powerline Ethernet Adapter works better when plugged into the wall socket. Connect the 200Mbps Powerline Ethernet Adapter into the power strip or surge protectors may degrade the network performance.
Chapter V : Specification Powerline Standards HomePlug AV Transfer Rate Up to 200 Mbps Modulation 1024/256/64/16/8 QAM, QPSK, BPSK Forward Error Correction Turbo Codes Protocol TDMA, CSMA/CA Security 128-bit AES Encryption LEDs 1 * Power 1 * PLC Link 1 * Ethernet Ethernet Interface 1 * RJ45 LAN Port Auto-negotiation, Auto MDI/MDIX Ethernet Standards Ethernet specification IEEE802.3, IEEE802.3u, IEEE802.3x Power 100 - 240VAC, 50-60 Hz Power Consumption 100mA (max.
