User`s manual

ManualsBrandsAir Techniques ManualsComputer equipmentPERI-PRO III

MAINTENANCE

QQUUAARRTTEERRLLYY -- CCLLEEAANN WWIITTHH FFOORRMMUULLAA 22000000

Clean the Peri-Pro III Transport with Formula 2000 quarterly or

whenever a black residue is evident on the transport or in the tanks.

UUssee tthhee PPeerrii--PPrroo TTrraannssppoorrtt CClleeaanniinngg KKiitt ((PPNN 4433997755))

Each kit contains:

 Cleaning tub  Brush and cleaning sponges  Twin pack of Formula 2000

CCAAUUTTIIOONN:: UUssee iinn aa wweellll vveennttiillaatteedd aarreeaa.. WWeeaarr pprrootteeccttiivvee ccllootthhiinngg,, rruubbbbeerr gglloovveess aanndd ggoogggglleess..

RReevviieeww tthhee MMaatteerriiaall SSaaffeettyy DDaattaa SShheeeett tthhaatt ccoommeess wwiitthh eevveerryy FFoorrmmuullaa 22000000 TTwwiinn PPaacckk..

11..

Turn the

PPOOWWEERR OOFFFF

and unplug the line cord. Remove the film receptacle; lift the cover off.

2..

Remove the transport and rinse under running water.

33..

Place the transport into the cleaning tub with the gears facing

up .

44..

Pour two bottles of Formula 2000 Component 1 into the

cleaning tub. Pour slowly. Do not splash or splatter solution -

wipe up any spills. (Use both bottles of Formula 2000 in the

Twin Pack to insure adequate cleaning of the transport.)

55..

Add cold water to the recessed line in the tub.

CCAAUUTTIIOONN:: UUssee ccoolldd wwaatteerr oonnllyy..

66..

Sprinkle two powder packets of Component 2 evenly across

the cleaning tub.

FFoorrmmuullaa 22000000’’ss eeffffeerrvveesscceenntt cclleeaanniinngg aaccttiioonn wwiilll

l bbeeggiinn aass ssoooonn aass CCoommppoonneenntt

22 iiss aaddddeedd.. SSoommee ooddoorr aanndd vvaappoorr wwiillll bbee eevviiddeenntt..

77..

Soak the transport for approximately 30 minutes, or until the effervescent action stops.

88..

Remove the transport and, under cold running water, remove any remaining deposits with the

brush; rinse.

99.. DDiissppoossee ooff

tthhee cclleeaanniinngg ssoolluuttiioonn iinn aaccccoorrddaannccee wwiitthh llooccaall ccooddeess..

Rinse the cleaning tub and

place the transport back in the tub. Fill with fresh water and drain. Rinse and drain at least 2

more times. (Be sure to rinse thoroughly since cleaner residue can contaminate fresh chemistry.)

1100..

Place the transport on a towel with the gears facing up and air dry thoroughly. Check that the

shutter area is dry before using. If not, dry with a soft, lint-free towel. See Fig. 14.

1111..

Change the water. Follow the steps for changing water under Daily Maintenance. If the wash tank

is particularly soiled or slimy, it must be thoroughly cleaned and rinsed. After cleaning, if the tank

was removed, clean and dry the tank drain stem receptacle in the base,reinstall the wash tank,

making sure the drain stem with the O-ring seats in the drain receptacle by pushing down straight

until the tank’s feet touch the base floor.

1122..

Clean the Dryer Transport if dry, white chemistry residue is evident on

the rollers.

 Remove the screw holding the dryer front cover plate in place.

 Slide the cover plate up, remove it and lift the dryer transport

straight up and out.

 Use warm water and a brush to remove the residue; rinse and

completely air dry.

 Reinstall the dryer transport and the cover plate.

IImmppoorrttaanntt:: TThhiiss

ppllaattee iiss nneecceessssaarryy ffoorr pprrooppeerr ffiillmm ddrryyiinngg..

1133..

Change the chemistry. Follow the steps for changing chemistry under Every Two Weeks

Maintenance.

1144..

Reinstall the transport and reassemble the Peri-Pro III. Follow the steps for reassembly under Every

Two Weeks Maintenance.

FIG. 13

FIG. 14