User manual

I-450-BE 19
STORAGE OF COOKING PROGRAMMES
To store a COOK-STEP or a set sequence in the ”PROG”
mode under a well-defined programme number, press the
and buttons simultaneously for about 1.5 seconds.
The indicator light above the button blinks for 1.5
seconds and then remains fixed. The display relating to
the cooking programmes is now activated and the increase
and decrease buttons may be used to choose a programme
number.
Make sure that the figures corresponding to programmes
that are already stored are always lit. The free storage
positions may be identified by the fact that the relative
number blinks. Choose a free storage position and then
press button for about 1.5 seconds until the relative
blinking indicator light remains fixed.
To exit from the storage programme, press the and
buttons simultaneously until the above-mentioned yellow
indicator light goes out.
The set cooking programme can now be found under the
chosen programming number. If an error occurs during
programming or if nothing has been stored, this sequence
may be interrupted. If the indicator light corresponding to
the button comes on, it is possible to exit from the
storage mode by pressing on the same.
Note: it is advisable to mark each parameter and set-up of
the stored cooking programmes in a table. This will ensure
correct combination between the different cooking modes
and programmes. This table also allows the programmes
to be rapidly stored again after any work carried out on the
electronic circuit by a technician.
ERASING A COOKING PROGRAMME
Using the button , select the ”AUTO” mode; the relative
indicator light comes on. Then press the and buttons
simultaneously for about 1.5 seconds. The indicator light
above button blinks for 1.5 seconds and then remains
fixed. Access to the stored programmes may now be gained
and the display for the cooking programmes is activated.
Using the increase and decrease buttons, the cooking
programme to be erased may be selected. Only a stored
programme number may be erased, i.e. the programme
number must appear lit up on the display.
CLEAR ENTRY (Fig.4 No.20)
Using the ”CLEAR ENTRY” button, the programme may
now be erased. Press the button until the number with a
fixed light on the display, corresponding to the programmes,
starts blinking, i.e. when the programme in question is in a
changeable buffer storage.
To exit from the erasing process and to erase the actual
cooking programme from the buffer storage, press buttons
and again until the yellow indicator light relating to
button goes out.
The programme is erased from the memory and this storage
position is consequently free.
CHANGING AND COMPLETING COOKING PROGRAM-
MES
To change a stored programme, proceed as for the erasing
stage. Follow the same sequence of operations described
above in the paragraph ”Erasing a cooking programme”,
including pressing the ”CLEAR ENTRY” button.
The programme in question is now in a buffer storage. This
is shown by a blinking number on the display corresponding
to the programmes. The parameters may now be changed
or the COOK-STEPS completed or erased. Press the two
buttons + simultaneously until the yellow indicator
light relating to button goes out. The change is now
stored.
OPERATING IN THE ”AUTO” MODE
After having switched on the appliance and chosen the
”AUTO” mode, the required cooking programme may be
recalled using the increase and decrease buttons.
All stored values and the cooking programme data are
shown by the relative indicator lights coming on. In addition,
the ”COOK-STEP” button may be used to recall the diffe-
rent cooking sequences.
START
STOP
START/STOP (Fig.4 No.3)
In the ”PROG” mode, after having selected the cooking
time, temperature, cooking mode and fan speed or a cooking
programme stored in the ”AUTO” mode, the cooking process
may be activated using the ”START/STOP” button. The
relative yellow indicator light comes on. The cooking process
may be interrupted by pressing on the ”START/STOP” button
for more than 3 seconds.
ALARM AND SELF-DIAGNOSIS
The system has the possibility of indicating failures and
operating anomalies on the display corresponding to the
cooking chamber temperature and the core temperature.
E Pt 1 Interruption or short-circuit of the temperature
sensor inside the cooking chamber
E Pt 2 Interruption or short-circuit of the temperature
sensor inside the steam generator
E Pt 3 Interruption or short-circuit of the core
temperature sensor
E Pt 4 Interruption or short-circuit of the temperature sensor
inside the by-pass tube (steam regulation)
E Pt 8 Interruption or short-circuit of the temperature
sensor on the electronic PC-board
E SCH Overheating of the electronic PC-board due to
lack of cooling air
E tub Intervention of the temperature limiter inside the
steam generator (T > 180°C)
E tuc Intervention of the temperature limiter inside the
cooking chamber (T > 320°C)
ECuP Break of the cooking time limitation (T >250°C)
EFLP Failure of the motor-activated steam release valve
for the cooking chamber (valid only for VIII, X)
Note: In the event of failure, a continuous audible alarm
can be heard and the error code is stored. The cooking
process may continue, e.g. in the event of failure of the
meat probe with the time as new parameter.