User manual

16
I-450-BE
COOK-STEP (Fig.4 No.5)
With this COOK-STEP storage, a cooking of cycle
consisting of six different sequences may be set: e.g.
browning, cooking and keeping the food warm.
Programming the sequences is described under ”Storage
of cooking programmes”.
The relative indicator lights have two colours showing the
COOK-STEP of the cooking process and the number of
programmed COOK-STEPS.
If the red indicator light is on, the COOK-STEP is working.
All the other programmed sequences which are not in
operation are shown by green indicator lights.
Indicator lights which are not on, correspond to the unused
COOK-STEPS.
Changing from one sequence to another is indicated by a
buzzer.
POWER STAGE SELECTION (Fig.4 No.6)
POWER STAGE 1
High fan speed - 100% heating power.
In neutral conditions, i.e. when the electrical circuit is
activated, the two indicator lights are off.
POWER STAGE 2
Reduced fan speed - 100% heating power.
By pressing the button once, the indicator light above the
fan symbol comes on.
POWER STAGE 3
High fan speed - 50% heating power.
By pressing the button a second time, the indicator light
above the coil symbol comes on.
POWER STAGE 4
Reduced fan speed - 50% heating power.
By pressing the button a third time, the two indicator lights
(fan and coil) come on.
Upon pressing the button again, the two indicator lights
go off and the control circuit goes back to its initial position,
i.e. in the power 1 position.
COOK AND HOLD (Fig.4 No.7)
This low temperature cooking programme is recommended
for ”Hot-air” and “Steam” programmes. Upon pressing the
”COOK & HOLD” button, the relative indicator lights above
the button start blinking.
If a programme is chosen by pressing the ”HOT AIR” or
”STEAM” button, a fixed programme is set with the
following sequence:
1.The heating power (hot air or steam) is reduced by 50%.
2.In the same way, the fan speed is also reduced.
In addition, the fan works intermittently after the regulated
temperature in the cooking chamber has been reached
(low temperature range).
If this programme is activated, the indicator light related
to this button comes on. The cycle stops when the set
time has elapsed.
4.4 Control panel - version X
ON/OFF SWITCH (Fig.4 No.1)
The ON/OFF switch is used to switch the appliance and
controls on or off. To switch the appliance on, lightly press
the button; to switch off keep the button pressed down for
about 3 seconds. This time delay avoids accidental
switching off during a cooking cycle.
When the appliance is switched off, this is indicated by
the green indicator light above the button going out. When
the appliance is switched on it lights up.
Note: upon switching off the appliance, wait at least 5
seconds before switching on again.
PROG/AUTO (Fig.4 No.2)
The ”PROG/AUTO” button can be used to set automatic
operation with all stored data or operation in the
programming mode. After having switched on the
appliance, the indicator lights to the side of the button
start blinking.
Pressing the touch pad once sets the ”PROG” mode; the
relative indicator light stops blinking and remains on. The
indicator light corresponding to the ”AUTO” mode goes
out. To change to the ”AUTO” mode, press the button again.
The change is shown by the relative indicator light coming
on.
Note: It is only possible to change to the ”AUTO” mode if
a cooking programme has been stored. Operation in the
”AUTO” mode is shown by the relative indicator light above
the button coming on.
START
STOP
START/STOP (Fig.4 No.3)
After having selected all data necessary for the cooking
process, such as temperature, cooking time, cooking mode
and fan speed, the cooking process may be started using
the ”START/STOP” button. The relative yellow indicator
light comes on.
This cooking cycle may be interrupted by pressing the
button during operation for more than 3 seconds.
COOKING PROGRAMMES (Fig.4 No.4)
If the cooking programmes have been stored (for storage
see paragraph ”Storage of cooking programmes”), they
may be selected using the increase and decrease buttons.
99 cooking programmes may be stored with a maximum
of 6 ”COOK-STEPS”, i.e. sub-programmes. If one of these
programmes is temporarily changed (e.g. the values
regarding temperature or cooking times), the selected
programme number will blink. If the change is not stored,
it will be erased when the appliance is switched off. To
return to the original programme, just press the button for
3 seconds.