Ether-FSH2402GT Mixed Gigabit Ethernet Switch Windows In-Band Management 24 × 10/100Base-TX ports 2 x 1000Base-T Gigabit Ports Auto MDI/MDI-X VLAN, Priority, Bandwidth Control Trunking, Loop Detection User’s Manual
Trademarks All rights reserved. AirLive Logo is an registered trademarks of OvisLink Corp, Taiwan. Other product names and company names are trademarks or registered trademarks of their respective owners. FCC Warning This equipment has been tested and found to comply with the requirements for a Class A digital device, pursuant to Part 15 of the FCC Rules. These requirements are designed for reasonable protection against harmful interference when the equipment operating in a commercial environment.
Table of Contents Table of Contents TABLE OF CONTENTS ........................................................................................I 1 PRODUCT OVERVIEW ........................................................................1 Introduction....................................................................................................................... 1 Windows Remote Management software ....................................................................... 1 Management Features ........
Table of Contents 2 PREPARATION BEFORE INSTALLATION.........................................6 Unpack the Package.......................................................................................................... 6 The Front Panel................................................................................................................. 7 Reset Button ...................................................................................................................... 7 The Rear Panel.........
Table of Contents System LEDs.................................................................................................................... 14 10/100Mbps Port LEDs .................................................................................................. 14 Gigabit Port LED............................................................................................................ 14 LED Table.......................................................................................................
Table of Contents Options menu ................................................................................................................ 29 APPENDIX A PRODUCT SPECIFICATIONS ..................................................30 APPENDIX B TROUBLESHOOTING...............................................................32 iv Ether-FSH2402GT Gigabit Ethernet Switch User’s Manual V1.
Table of Contents Figures Fig. 2-1 Package Contents .............................................................................................. 6 Fig. 2-2 Front Panel ....................................................................................................... 7 Fig 2-3 The Reset Button............................................................................................... 7 Fig. 2-4 Rear Panel .............................................................................................
Table of Contents Tables Table 2-2 Cabling type for 10/100BASE-TX and 1000Base-T.................................... 11 Table 4-1 System & Station Port LEDs........................................................................ 15 vi Ether-FSH2402GT Gigabit Ethernet Switch User’s Manual V1.
1 Product Overview 1 Product Overview Introduction Windows Remote Management software Conventionally, configuring a switch's smart management will require users to attach the computer (serial or printer port) directly to the switch's console port. With Ether-FSH2402GT's in-band management capability, users can configure the switch through the Ethernet network. The included Windows management software provides a very simple point-and-click interface to set all the functions.
1 Product Overview prevents the broadcast traffic from overflowing the network. Loop detection alert the user when there is a loop formed inside the network on the front panel LED. The management software's diagnostic function even report which ports the loop occurs. Port setting setting port speed and duplex mode, flow control Authentication Keys The switch support authentication key feature for the management function. This will prevent unauthorized users from changing the switch’s settings.
1 Product Overview VLAN membership by groups of switch ports. Port grouping is the most common method of defining VLAN membership, and its configuration is straightforward. But, when a user moves from one port to another, it takes a network manager to manually reconfigure VLAN membership. With manual VLAN configuration, both the initial setup and all subsequent moves and changes are controlled by the network administrator, enabling a high degree of control.
1 Product Overview Product Features • • Standard Compliance o IEEE 802.3 10Base-T Ethernet o IEEE802.3u 100BaseTX o o IEEE802.3ab 1000Base-T o o o • Configure several switches on one program standard o Windows Remote Management Software standard o Smart Remote Managements: o Management through Ethernet network IEEE 802.3u Nway auto-negotiation o Authentication Key function IEEE802.
1 Product Overview • Trunk groups in 2 or 4 ports Dimensions: 432 × 180 × 44 mm, 19" rack mountable o group management • Weight: 2.7 kg • Built-in power supply: 100~240 VAC, o Broadcast Storm Control to limit broadcast traffic 50 ~ 60 Hz, 0.4A, 10 Watts max.
2 Preparation before Installation 2 Preparation before Installation Unpack the Package Before you begin the installation of Ether-FSH2402GT Fast Ethernet Switch, make sure that you have all the necessary accessories that come with your package. Follow the steps below to unpack your package contents: 1. 2. 3. Clear out an adequate space to unpack the package carton. Open the package carton and take out the contents carefully.
2 Preparation before Installation The Front Panel The front panel is where you can find the twenty-four 10/100Mbps station ports , 2 Gigabit Ports, and the LED indicators. For the technical specifications of the ports, please refer to Appendix A, Product Specifications for detailed information. For information concerning LED indicators, please refer to Chapter 4, LED Indicators. Station Port LEDs Power LED Gigabit Ports Station Ports DIAG LED Fig.
2 Preparation before Installation AC Power Connector This is a three-pronged power connector where the power cord should be attached. Just plug the female end of the power cord into the connector, and the male end of the power cord into an AC power outlet. The switch supports an input voltages ranging from 100 ~ 240 VAC @ 50~60 Hz . Power Switch Fig. 2-4 Rear Panel 8 Ether-FSH2402GT Gigabit Ethernet Switch User’s Manual V1.
3 Installation of the Switch 3 Installation of the Switch Quick Installation Ether-FSH2402GT Fast Ethernet Switch is fully compliant with 10/100BASE-TX Fast Ethernet standards. 5 Steps to Quick Installation Step 1. Power on the Switch. Step 2. Connect network devices to the Switch: connect either workstation, server, switch, bridge or router to the station port (10/100BASE-TX), using 100 ohm unshielded twisted pair (category 5 UTP) or shielded twisted-pair (STP) cable. Step 3.
2 Preparation before Installation Fig. 3-2 Attaching the Switch to a 19-inch rack Desktop Installation Ether-FSH2402GT Fast Ethernet Switch has four rubber pads attached on each corner of its underside. These pads serve as cushionings against vibration and prevent the switch from sliding off its position. They also allow adequate ventilation space when you place the switch on top of another device. Fig.
3 Installation of the Switch • • • • • The switch should not be placed near large electric motors or other strong electromagnetic sources. As a reference, the strength of the electromagnetic field on site should not exceed the (RFC) standards for IEC 801-3, Level 2(3V/M) field strength. The air temperature in the location should be within a range of 32 to 122 °F (0 to 55°C). The relative humidity in the location should not exceed 95% non-condensing humidity.
2 Preparation before Installation Making your own UTP/STP cable The twisted-pair cable provided an eight-pin plug at each end that mate with the twisted-pair port on the adapter and with a RJ-45 wall jack. If you are marking your own interface cables to use as dedicated network wiring or as extension cables, please follow the guideline below: Each UTP/STP cable contains eight wires in either 568A or 568B color scheme (please see Fig 2-7).
3 Installation of the Switch Power Switch Power Connector Power Outlet Fig 3-13 Connecting the Switch to power outlet 13 Ether-FSH2402GT Gigabit Ethernet Switch User’s Manual V1.
4 LED Indicators 4 LED Indicators Before connecting any network device to Ether-FSH2402GT Fast Ethernet Switch, you should take a few minutes to look over this chapter and get familiar with the front panel LED indicators of your Switch. System LEDs 10/100Mbps Port LED Gigabit LED System LEDs - Power (green) to indicate power on/off status LoopDet (yellow) to indicate network loop has formed inside the network.
4 LED Indicators LED Table LED indicator Color Status Meaning System LEDs Power LED ● Green ON OFF Power ON Power OFF ● Yellow ON OFF Detect a loop even in the network Loop not detected ● Yellow ON OFF POST has failed POST is O.K.
5 Management Software Guide 5 Management Software Guide Introduction The OvisLink Windows remote management software allows user to configure the management function though the LAN port. It uses a specialized RRCP protocol and does not use the IP protocol. It operates inside the Ethernet network.
5 Management Software Guide Installing the Software Please follow the procedures below to install the management program into your Windows 1. Insert the OvisLink CD into your computer, the Product CD menu should show up automatically. If not, on the File Explorer, please click on “setup.exe” to begin. 2. Click on “ETHER/SNMP Series” and select the “Ether-FSH2402GT” 3. Follow the instruction on screen to install the “WinPCap” and “The Remote Management Utility” 4.
5 Management Software Guide Note: If your switch doesn’t show up in the menu. Please reset the switch and press “update button”. There are 4 major functions on the management screen “Status”, “Configuration”, “Security”, and “Diagnostic”. We will discuss them in the following sections. Please make sure to save to the hardware after changes. Status Functions Click on the Status Tab of the management screen will bring you the overview, port status, and MIB counter sub menus.
5 Management Software Guide Discovered device information: List all switches founded in the network. You can named the switches by double-click the item in the list box. Network topology link vector: Show the link status of the switches. Update button If you want to know the newest switch’s information of the network, press the Update button. Switch database button You can view the switch database. The database dialog box displays switch’s name, mac address and authentication Key.
5 Management Software Guide MIB Counter Submenu You can view the MIB counter about the RX, TX and Diagnostic Counter. Click the Diagnostic Counter column header, there are three object you can select, such as Drop count, CRC error count and Collision count. Byte Count Button You can set the unit of the RX and TC counter to Byte count. Packet Count Button You can set the unit of the RX and TC counter to Packet count. Bandwidth Utilization Button Displayed the per-port traffic utilization.
5 Management Software Guide Port Status Submenu You can view the port status of the switch that you select. The list box will show the status of port1, port2…,and port26. The port status includes port type, enabled status, link status, speed duplex, flow control, Tx bandwidth control, Rx bandwidth control, and trunk setting status. 21 Ether-FSH2402GT Gigabit Ethernet Switch User’s Manual V1.
5 Management Software Guide Configuration Functions Port Configuration Submenu Press the “Config” button, and you will see a dialog like follows. Put the check in the item you want to configure. Select ports to config: 22 Ether-FSH2402GT Gigabit Ethernet Switch User’s Manual V1.
5 Management Software Guide Please select a port to set settings Port Enable: The default is to enable the port. Check the “Disable” if you want to disconnect the port Tx Bandwidth Control Enable this function will restrict the given port’s sending speed to the selected value. Rx Bandwidth Control Enable this function will restrict the give port’s receiving speed to the selected value Speed Advertised Changing the speed and duplex mode of a given port.
5 Management Software Guide Qos Configuration is used to configure the Qos control registers. Press the Refresh button to read the status of the registers. Press the Update button to set the registers. VLAN Configuration Submenu This page is used to configure the vlan table registers. Refresh button 24 Ether-FSH2402GT Gigabit Ethernet Switch User’s Manual V1.
5 Management Software Guide Read the VLAN table registers. If you can have configured VLAN but it doesn’t show on the table, please press the button Add VLAN button Click the ADD VLAN button will pop up a configuration window below. Select port base or tag base VLAN, then check the port where you want to configure the settings. For Tag Base VLAN, please enter a VLAN ID number. Port Tagging Control button Press this button you will see a dialog like follows.
5 Management Software Guide Press the Refresh button to read the vlan control registers. Press the Update button to set the registers, and it will set all vlan control registers to the selection. Device Feature Setting IGMP Snooping Control register and IP Multicast Router Port Discovery register. Router port report will show the IP multicast Router port list. Press the Refresh button to read the register. Press the Update button to set the registers, and it will set the register to the selection.
5 Management Software Guide Security Function This page displays the authentication key of the switch, and the RCP Management Security Mask Configuration. The authentication key is readable in this version. You can press the Refresh button to read the register. 27 Ether-FSH2402GT Gigabit Ethernet Switch User’s Manual V1.
5 Management Software Guide Diagnostic Function Fault Information Show some information likes Trunk Port Fault, Network Loop Fault Test, and Gigabit PHY existence report for Gigabit Port G1G2. Device Reset The software reset will reset the system to the initial state. The MAC table and VLAN table data will be kept. All the current user configured values of internal registers will be kept. The EEPROM download will NOT be done again. But the system will restart the process of Auto Negotiation .
5 Management Software Guide Pull down Menus There are totally of 4 pull down menus at the top of the screen. We will explain the function of each one. System menu Save and Load Configuration You can save or load the configuration to a file. To save a file, do one of the following: In the menu, click System | Save Configuration . Note: The configuration file are named by the switch’s MAC address. To load a file, do one of the following: In the menu, click System | Load Configuration .
Appendix A Production Specifications Ether-FSH2402GT Fast Ethernet Switch Appendix A Product Specifications • Standard Compliance IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.1q VLAN standard IEEE 802.1p Class of Service IEEE 802.1ad Link Aggregation ANSI/IEEE Std 802.
Appendix A Product Specifications • Full Duplex • Active Flow Control Auto-negotiation IEEE 802.3x compliant flow control for full duplex Back Pressure for half duplex • Filtering Address Table 8 K per device • RAM Buffer 2.
Appendix A Production Specifications Appendix B Troubleshooting This appendix contains specific information to help you identify and solve problems. If your switch does not function properly, please make sure it is set up according to the instructions on the manual. If you suspect your switch is not connected correctly to your network, check the following points before you contact your local dealer for support. • • • • • • • • • Make sure the Power is ON (Check the Power LED).
