BC-5010 5-Mega Pixel Box Type PoE IP Camera User’s Manual
Copyright and Disclaimer Copyright & Disclaimer No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recording without the written consent of OvisLink Corp. OvisLink Corp. has made the best effort to ensure the accuracy of the information in this user’s guide. However, we are not liable for the inaccuracies or errors in this guide. Please use with caution.
Copyright and Disclaimer FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of Contents Table of Contents 1. Overview .....................................................................................................1 1.1 Introduction ..........................................................................................1 1.2 Features ...............................................................................................2 1.3 Product Specification............................................................................3 1.4 System Requirement................
Table of Contents 6.6 Wireless .............................................................................................35 7. Video Settings ..........................................................................................36 7.1 Video Profile.......................................................................................37 7.2 Exposure............................................................................................37 7.3 Image..................................................
Table of Contents 12.4 System Log......................................................................................59 13. Appendix.................................................................................................61 A. Alarm I/O Connector ............................................................................61 B. Frequently Ask Questions....................................................................62 C. Ping IP Address...........................................................
1. Overview 1. Overview 1 This user’s guide explains how to operate this camera from a computer. A user should read this manual completely and carefully before you operate the device. 1.1 Introduction AirLive BC-5010 is a standalone system that can be connected directly to an Ethernet or Fast Ethernet network. Equipped with a powerful 5 Mega pixel color CMOS sensor, the camera allows you to capture a wider field of view which is up to 2592 x 1920 resolution. With supporting for latest H.
1. Overview 1.2 Features This manual will illustrate the steps of how to setup and operate this IP camera, so you’ll also soon be enjoying the benefits of these product features: Easy installation with setup wizard UPnP device discovery and NAT router transversal for easy installation Dynamic IP Service, DIPS®, to search your IP camera from Internet easily 0.2Lux Minimum Illumination at F1.2 Support iSCSI, WDR enhanced DC IRIS and IR-CUT Removable(ICR) H.
1. Overview 1.3 Product Specification Model Camera Type Image Sensor Sensor Resolution Lens Type Camera Video Night Vision Max IR Distance Minimum Illumination Mechanical IR-Cut Filter Auto Iris Viewing Angle Pan/Tile Control Analog Video Out Video Compression Video Profile Resolution and Frame Rate Streaming ROI BC-5010 Indoor Box Type 1/2.5” 5 Mega Pixel Color CMOS Sensor 2592 X 1920 C/CS Mount Lens Support Removable Lens Built-In Removable IR Cut Filter None 0.
1. Overview Image Processing Digital Zoom Audio Encoder Audio Network Audio Streaming Audio Input/Output AE, AWB Saturation, brightness, sharpness, contrast, Hue Mirror/Flip Text, time and date OSD 10X G711 u-law AMR Two-way speaker port and microphone port Ethernet One RJ45 Port; IEEE 802.3u Compliant 10/100 Mbps Fast Ethernet with Auto-MDIX PoE Wireless IEEE802.
1.
1. Overview 1.4 System Requirement For normal operation and viewing of the network camera, it’s recommended that your system meets these minimum requirements for proper operation: Item CPU Requirements VGA Monitor resolution 1280 x 1024 or higher Memory Size Operating System Recorded File Playback 512MB or more Web Browser Pentium-4 2.0 GHz or higher Window XP, Vista or Windows 7 Microsoft Media Player 11.0 or later Microsoft Internet Explorer 7.
2. Package Contents and Installation 2. Package 2 Contents and Installation 2.1 Package Content A user can find the following items in the package as below: 1. AirLive BC-5010 is the main part of the product with Camera Mount Kit. Note: The lens is optional. For further information about the lens, please check with your installer. 2. Power Adapter: 12V DC electric power output to BC-5010. 3.
2. Package Contents and Installation 2.2 Connections Front / Top / Side Panel 1. DC-iris Connector: It allows you to attach the DC-Iris lens (optional). 2. C and CS Lens Focus Ring: You can adjust C and CS lens focus ring to fit your lens type.
2. Package Contents and Installation 1. RJ45 LAN socket: Connect to PC or Hub/Switch. For connections to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 cable to connect the Network Camera to a 100Mbps Fast Ethernet network switch or hub.
2. Package Contents and Installation MIC in (audio in): Connect a microphone to the network camera. Audio out: Connect a loud speaker to the network camera. This function is for voice alerting and two-way audio. 5. Iris Level: It is used only when the DC-Iris lens is connected to the camera. This screw-knob allows you to adjust the brightness of the video images from the DC-Iris lens. 6. SD Card Slot: SD Card Slot allows you to insert a memory card for expansion of storage. 7.
2. Package Contents and Installation Fix the camera to ceiling with the three supplied screws. 2. Connecting to LAN You can use the provided Ethernet cable to connect the camera to your local area network (LAN). When you connect the AC power adapter, the camera is powered on automatically. You can verify the power status from the Power LED on the Ethernet port. Once connected, the Link LED starts flashing green light and the camera is on standby and ready for use now.
2. Package Contents and Installation 3. Connect the external power supply to Camera Connect the attached power adapter to the DC power jack of the camera. Note: Use the 12VDC power adapter, included in the package, and connect it to wall outlet for AC power. Once you have installed the camera well and powered it on, the power LED (orange) will turn on later. When the power LED turned on, it means that the system is booting up successfully.
2. Package Contents and Installation When you use a DC-Iris lens on your camera, you can adjust the brightness of the video image through the Iris Level screw-know on the back panel of the camera. C and CS Lens Focus Adjustment You can adjust C and CS lens focus ring to fit your lens type. 4. Applications of the Camera The camera can be applied in multiple applications, including: z Monitor local and remote places and objects via Internet or Intranet.
2. Package Contents and Installation z Capture still images and video clips remotely. z Upload images or send email messages with the still images attached. The following diagram explains one of the typical applications for your camera and provides a basic example for installing the camera. Home Applications of the Internet Camera 2.4 Connect AirLive X.USB for wireless function (Optional) You can add wireless function to your BC-5010 by connecting the optional AirLive X.
2. Package Contents and Installation 4. 2.5 Connect to IP Camera 1. Insert the bundle CD into your PC/Laptop. 2. Auto Run Screen then shows up; click “Install Software Æ “IPWizard II” to install the configuration tool software.
2. Package Contents and Installation 3. After completing installation, run the configuration tool software.
2. Package Contents and Installation 4. The Software scans the network and finds the IP Camera and then lists them in the dialog box. 5. If the Camera’s IP address is in the same IP segment as your LAN, select the founded IP Camera and double click on the item. Then, the default browser will show up and connect to the IP camera’s Web automatically.
3. Using IP Camera via Web Browser 3 3. Using IP Camera via Web Browser 3.1 Win dows Web Browser 1. Open your web browser, and enter the IP address or host name of the IP camera in the Location / Address field of your browser. Note: If you only want to view the video without accessing Setting screen, enter “http:///index2.htm” as your web URL. 2. Use the default account “admin” and default password “airlive”.
3. Using IP Camera via Web Browser is “Configuration”. For more details, you can check the following chapters.
4. Operating IP Camera via Mobile Phone 4 4. Operating IP Camera via Mobile Phone 4.1 Using IP Camera via iPhone You can access to your IP camera via your iPhone. Please follow the setting process below. Then you can see the live view via iPhone. 5. 2. Execute AirLive CamPro Mobile 1. Download AirLive CamPro Mobile from APP store 6. 7. 8. 9. 10. 11. 12. 3. Click Setup button. 4. Setup page appears 13. 14. 15. 16. 17. 18.
4. Operating IP Camera via Mobile Phone 19. 5. Click Add button. 20. 21. 22. 23. 24. 25. 26. 27. 6. Click LAN button and select the camera. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39.
4. Operating IP Camera via Mobile Phone odel, Address, HTTP Port info 40.7. aMppear on the page. 8. Key-in Username and Password then click OK button. 41. 42. 43. 44. 45. 46. 47. 10. The video appears on the main screen. 9. Click Live View button 48. 49. 50. 51. 52. 53. 54. 55. 56. 57. Notes: App for Android will be available in 11/2013. Note: The image is continuous snapshots, not video. Thus, live image can’t be recorded here.
5. Configuration of Main Menu 5. Configuration 5 of Main Menu In the left side of main configuration is Configuration. For more details, please check the following Chapters. In the left side, you can control Live View in your main Browser. The functions include Function Buttons, Streaming Protocol, Video Profile, Monitor Image Section, Language and Digital Output.
5. Configuration of Main Menu 5.1 Live View 1. Function Buttons You can use the function buttons to control the camera’s audio, video, and zoom functions. z : Original screen to full Screen z : Full screen to original screen z : Enlarge the image of the camera digitally. z : Reduce the image of the camera digitally. z : Snapshot z : Record video z / : Click to mute/unmute the microphone of the camera. When it is unmuted, you receive the on-site sound/voice where the camera is installed.
5. Configuration of Main Menu 2. Monitor Image Section The image from BC-5010 is shown here. 3. Streaming Select to transmit and record the video using H.264 (MPEG4), or MJPEG compression. 4. Video Output User can select proper streaming protocol according to networking environment. 5. Active X Caching The buffer of Active X. If the bandwidth is limited, you can adjust to higher value but the higher value causes more latency. 6. Language The device can provide multiple languages to meet user’s requirement.
5. Configuration of Main Menu 5.2 Configuration This function is only for the Administrator. In the left side of main configuration, you can see Configuration including below.
5. Configuration of Main Menu Item Action Network The Network menu contains the networking related settings for the camera, such as the IP Setting, DDNS Setting, IP Filter, etc. For more detail information, you can refer to Chapter 6. Video Configure bit rate and frame rate of video profiles, camera parameters, day & night. For more detail information, you can refer to Chapter 7. Audio Configure audio parameters. For more detail information, you can refer to Chapter 8.
6. Configuration-Network 6 6. Configuration-Network Click the Network to display the sub-menus including General, UPnP/Bonjour/ QoS, IP Filter, IP Notification, iSCSI.
6. Configuration-Network 6.1 General LAN Interface: This field allows you to select the IP address mode and set up the related configuration. The avail options include: DHCP IPv4, DHCP IPv4/IPv6, and Static IPv4/IPv6. - DHCP IPv4: Select this option when your network uses the DHCP server. When the camera starts up, it will be assigned an IP address from the DHCP server automatically. - DHCP IPv4/IPv6: DHCP for IPv6 enables the DHCP server to pass the configuration parameters (e.g.
6. Configuration-Network IP Address (IPv4/IPv6) Enter the IP address of the camera. The default setting is 192.168.1.100. Subnet Mask Enter the Subnet Mask of the camera. The default setting is 255.255.255.0. Default Gateway Enter the Default Gateway of the camera. The default setting is 192.168.1.254 Primary/ Secondary DNS DNS (Domain Name System) translates domain names into IP addresses. Enter the Primary DNS and Secondary DNS that are provided by ISP. HTTP Port The default HTTP port is 80.
6. Configuration-Network Enable PPPoE: Select this option when you use a direct connection via the ADSL modem. You should have a PPPoE account from your Internet service provider. Enter the User Name and Password. The camera will get an IP address from the ISP as starting up. NOTE Once the camera get an IP address from the ISP as starting up, it automatically sends a notification email to you.
6. Configuration-Network 1. UPnP: The camera supports UPnP (Universal Plug and Play), which is a set of computer network protocols that enable the device-to-device interoperability. Select the Enable Discovery option to enable the feature. In addition, it supports port auto mapping function so that you can access the camera if it is behind an NAT router or firewall. Select the Enable Port Mapping option to enable the feature. 2.
6. Configuration-Network 6.4 IP Notification In case the IP address is changed, system is able to send out an email to alert someone if the function is enabled. 1. Notification (e-mail): If enable this function, then the “Send to “and “Subject” fields need to be filled. - Send To: Type the receiver’s e-mail address. This address is used for reply mail. - Subject: Type the subject/title of the E-mail. 2.
6. Configuration-Network - Message: The message will be sent to FTP server. 3. HTTP Notification: If enable this function, then the fields below need to be filled. - URL: Type the server name or the IP address of the HTTP server. - HTTP Login name: Type the user name for the HTTP server. - HTTP Login Password: Type the password for the HTTP server. 6.5 iSCSI Enable the iSCSI and key-in server IP address and Port number. The disk of the server will be storage in IP cam setting.
6. Configuration-Network 6.6 Wireless When you insert AirLive X.USB to BC-5010 USB port, the wireless page will appear. After enabling the wireless function, please choose your wireless SSID and key in security key, then click Apply button to save the settings. When you complete the setting, please unplug the internet cable and search BC-5010 again by AirLIve IP Wizard II. 7.Note: Make sure that plug power adapter to power on BC-5010.
7. Video Settings 7. Video 7 Settings Click the Video to display the sub-menus including Video Profile, Exposure, Image, WDR, Overlay settings of the camera. .
7. Video Settings 7.1 Video Profile 1. ROI: ROI means Region of Interest. When the main stream is set to High Resolution, user can select specified region for monitoring, for this will saving the bandwidth if there are too many collision on the network. 2. Main Stream & Second Stream: To adjust the camera to capture images in several resolutions (up to 2592 x 1920 @ 15fps) in H.264, MPEG4, or MJEPG format.
7. Video Settings 2. Others - Modes: There are three modes (Indoor, Outdoor, and Auto) to fit your environment - Auto White Balance: You can enable or disable the function. - Auto Iris: When you attach a DC-Iris lens with the auto Iris function, select ON/OFF to enable/disable the feature. - IR-Cut: IR-Cut filter is used for the camera to produce true color images, which avoids the color deviation for the captured images effectively.
7. Video Settings 7.3 Image 1. Image Setting - Brightness: Adjust the brightness level from 0~255. - Contrast: Adjust the contrast level from 0~255. - Saturation: Adjust the colors level from 0~255. - Sharpness: Adjust the sharpness level from 0 ~ 100. TIP: Click Default to restore the default settings of the three options above. 2. Others - Mirror: Select Vertical to mirror the image vertically, or select Horizontal to mirror the image horizontally.
7. Video Settings 7.4 WDR 1. WDR Setting You can adjust WDR level to fix your backlight environment. 2. BLC Setting You can adjust BLC level to fix your backlight environment.
7. Video Settings 7.5 Overlay This option is used to set the image overlay and mask feature of the camera. 1. Overlay Setting - Enable Time Stamp: Select this option to display the date & time information on the live view image. - Enable Text Display: Select this option and enter your heading text in the box to display the text information on the live view image. You can set the displayed text in transparent mode by selecting the Transparent option.
7. Video Settings - User Define Image: When you select User Define Image, you can click Browse to select the image file from your computer and then click Update to apply the setting. NOTE The width and height of the input overlay graphic should be multiple of 4 at a maximum size of 160x128, and in JPG or BMP (24-bit RGB) format.
8. Playback 8. Audio 8 Click the Audio to display the sub-menus including Audio Setting. 8.1 Audio Setting 1. Microphone: Select the option to enable the camera’s audio in function, so that you can receive the on-site sound and voice from the camera. 2. Speaker: Select the option to enable the camera’s audio out function, so that the connected speaker can play the sound and voice through the camera. 3. Recording File: You can upload audio file for event action.
9. Event 9. Event 9 Click the Event to display the sub-menus including Event, Event Schedule, Motion Detection. 9.1 Event 1. Media Format: Select One Snapshot to send the alert message with one still image captured by the camera, or select H264 Video to send the alert message with one video clip recorded by the camera. You can set the attachment that is captured in Pre Event or Post Event time when the event has been triggered.
9. Event 2. FTP Event Server: Select Enable to enable the FTP server for the camera. - FTP Server: Enter the IP address of the target FTP server. - Port: Enter the port number used for the FTP server. - User Name: Enter the user name to login into the FTP server. - Password: Enter the password to login into the FTP server. - File Path Name: Enter the destination folder for uploading the images. For example, /Test/. - Enable Passive Mode: Select the Enable option to enable passive mode.
9. Event NOTE Due to the network environment, the camera may not upload number of images that you set. 5. HTTP Event Server: Select Enable to enable the Http server for the camera. - URL: Enter the IP address of the HTTP server. - HTTP Port: Set port number of HTTP server. - User Name: Enter the user name to login into the HTTP server. - Password: Enter the password to login into the HTTP server. NOTE Due to the network environment, the camera may not upload number of images that you set. 9.
9. Event - Enable SD CARD: The camera will store the attachment to the SD card when triggered. - Enable USB: The camera will store the attachment to the USB flash drive when triggered. - Trigger digital output: The camera will trigger the connected device on the camera’s output for 1~60 seconds (according to the setting of the pull-down menu). - Audio File Playback: The camera will play voice file when triggered. 8. When done, click Add. The event profile will be added to the Event list.
9. Event 9.3 Motion Detection The Motion Detection option contains the commands and settings that allow you to enable and set up the motion detection feature of the camera. The camera provides three detecting areas. Follow the steps below to set up the Motion Detection function for the camera: 1. Select Enable Motion Detection. 2. Select Window 1/2/3. When the detecting area is enabled, you can use the mouse to move the detecting area and change the area coverage. 3.
10. RS-485 10. RS-485 10 Click the RS-485 to display the sub-menus including RS-485 Settings, RS-485 PTZ. 10.1RS-485 Settings The RS-485 option provides the control settings for external device through the I/O port. Select Enable RS-485 and complete the required settings to activate the RS-485 function of the camera.
10. RS-485 Use Pelco-D: Select this option and then select an Address. When you enable the RS-485 function of the camera, you will be able to use the RS-485 Buttons on the live view screen to control the camera. Use Custom Protocol: Select this option to configure the commands protocol manually. When you select this option, you need to complete the required settings of Port Setting. You can click Test to test each command that you have assigned.
11. System 11. System 11 Click the System to display the sub-menus including Device Settings, Account, Management Ports, Firmware, Maintenance.
11. System 11.1Device Settings Use this menu to perform the principal settings of the device. 1. DPS - DIPS (Dynamic IP Service): To enable or disable the DIPS® (Dynamic IP Service) function. - Device ID (for DIPS): It’s a unique number of each device for identification and this ID is used for DIPS. This function now is reserved for future use. 2. Information: The information of Camera Name and Location. 3. Indication LED: This item allows you to set the LED illumination as desired.
11. System 2. Users - User Name/Password/Confirm Password: Enter the user’s name you want to add to use the camera. Then, enter the password twice for the new user. When done, click Add to add the new user for the camera. - User List: Display the existing users of the camera. To delete a user, select the one you want to delete and click Delete. 3. Guest - User Name/Password/Confirm Password: Enter the user’s name you want to add to use the camera. Then, enter the password twice for the new user.
11. System 11.3 Management Ports 1. HTTP: To define HTTP Ports. The default HTTP port is 80 2. HTTPS: Select the Enable HTTPS option to enable HTTPS, which is a secure protocol to provide authenticated and encrypted communication within your network. - HTTPS Port: Assign a HTTPS port in the text box. The default HTTPS port is 443. 11.4 Firmware 1. Update Firmware: You can upgrade the firmware for your camera once you obtained a latest version of firmware.
11. System 11.5 Maintenance 1. Factory Reset: Click Reset to restore all factory default settings for the camera. 2. System Rebooted: Click Reboot to restart the camera just like turning the device off and on. The camera configuration will be retained after rebooting. 3. Configuration Backup/Restore: You can save your camera configuration as a backup file on your computer. Whenever you want to resume the original settings, you can restore them by retrieving the backup file.
11.
12. Status 12. Status 12 Click the Status to display the sub-menus including Basic, Audio/Video, Network, System Log. 12.1 Basic Basic information includes Camera Name, Firmware version, MAC, Camera Date & Time. 12.2 Audio/Video 1. Video -H.264: Video Resolution/Video Quality/Frame Rate -MJPEG: Video Resolution/Video Quality/Frame Rate -Mobile View: 3GPP (Enable/Disable) 2.
12. Status 12.3 Network 1. Wired Interface IP Mode DHCP or Static IP Address (IPv4/IPv6) IP address of the camera. The default setting is 192.168.1.100. Subnet Mask Subnet Mask of the camera. The default setting is 255.255.255.0. Gateway Gateway of the camera. The default setting is 192.168.1.254 Primary/ Secondary DNS DNS (Domain Name System) translates domain names into IP addresses. Enter the Primary DNS and Secondary DNS that are provided by ISP.
12. Status 2. Wireless Interface Status Status of LAN and Wireless IP Address IP address of the camera. Subnet Mask Enter the Subnet Mask of the camera. The default setting is 255.255.255.0. Gateway Gateway of the camera. The default setting is 192.168.1.254 MAC A media access control address (MAC address) is a unique identifier assigned to network interfaces for communications on the physical network segment. 12.4 System Log You can check the usage log of IP camera here.
12.
13. Appendix 13. Appendix 13 A. Alarm I/O Connector Some features of the Camera can be activated by the external sensor that senses physical changes in the area Camera is monitoring. These changes can include intrusion detection or certain physical change in the monitored area. For examples, the external sensor can be a door switch or an infrared motion detector. These devices are customer provided, and are available from dealers who carry surveillance and security products.
13. Appendix Explanation of External I/O Circuit Diagram: CAUTION! • THE LOW VOLTAGE/CURRENT CIRCUITS AND HIGH VOLTAGE/ CURRENT CIRCUITS ARE IN THE NETWORK CAMERA CIRCUIT. THE QUALIFIED ELECTRICIAN SHOULD DO THE WIRING NOT BY YOURSELF. INCORRECT WIRING COULD DAMAGE NWTWORK CAMERA. YOU COULD RECEIVE THE FATAL ELECTRIC SHOCK. • THE EXTERNAL I/O IS NOT CAPABLE OF CONNECTING DIRECTLY TO DEVICES THAT REQUIRE LARGE AMOUNTS OF CURRENT.
13. Appendix Install this device Status LED does not light up. The network cabling is required for the device. The device will be installed and work if a firewall exists on the network. The username and password for the first time or after factory default reset Forgot the username and password Forgot the IP address of the device. IPWizard II program cannot find the device. Internet Explorer does not seem to work well with the device IPWizard II program fails to save the network parameters.
13. Appendix Some IP cameras are working but others are failed • Maybe UPnP function of NAT router is not compatible to the IP camera. Please contact your dealer to get the approval routers list. • Maybe too many IP cameras have been installed on the LAN, and then NAT router is out of resource to support more cameras. You could turn off and on NAT router to clear out of date information inside router.
13. Appendix Contact your dealer for further help. Image or video does not appear in the main page. Check the device’s ActiveX is installed on your computer • The first time the PC connects to Network Camera, a pop-up Security Warning window will appear to download ActiveX Controls. When using Windows XP, or Vista, log on with an appropriate account that is authorized to install applications. • Network congestion may prevent the Image screen from appearing quickly.
13. Appendix slow video when audio is enabled. support a higher frame rate for the streamed image size. Try reducing the video streaming size to 160x120 or 320x240 and/or disabling audio. • Audio will consume 32 kbps. Disable audio to improve video. Your Internet connection may not have enough bandwidth to support streaming audio from the device. Image Transfer on e-mail • Default Gateway and DNS server address should be set up correctly. or FTP does not work.
13. Appendix C. Ping IP Address The PING (stands for Packet Internet Groper) command is used to detect whether a specific IP address is accessible by sending a packet to the specific address and waiting for a reply. It’s also a very useful tool to confirm Network Camera installed or if the IP address conflicts with any other devices over the network. If you want to make sure the IP address of Network Camera, utilize the PING command as follows: z Start a DOS window. z Type ping x.x.x.x, where x.x.x.
13. Appendix D. Bandwidth Estimation The frame rate of video transmitted from the device depends on connection bandwidth between client and server, video resolution, codec type, and quality setting of server. Here is a guideline to help you roughly estimate the bandwidth requirements form your device. The required bandwidth depends on content of video source. The slow motion video will produce smaller bit rate generally and fast motion will produce higher bit rate vice versa.
13. Appendix (1) Assign a local/fixed IP address to your device (2) Access the Router with Your Web browser (3) Open/Configure Virtual Server Ports of Your Router (1) Assign a local/fixed IP address to your device The device must be assigned a local and fixed IP Address that allows it to be recognized by the router. Manually setup the device with a fixed IP address, for example, 192.168.0.100.
13. Appendix Your WAN IP Address will be listed here. Note: Because a dynamic WAN IP can change from time to time depending on your ISP, you may want to obtain a Static IP address from your ISP. A Static IP address is a fixed IP address that will not change over time and will be more convenient for you to use to access your camera from a remote location. If you could not get a Static IP address from your ISP, the DIPS™ or DDNS is a solution alternatively. Please refer to Appendix G for more information.
13. Appendix • Select Both under Protocol Type (TCP and UDP) • Enter your camera’s local IP Address (e.g., 192.168.1.100, for example) in the Private IP field • If you are using the default camera port settings, enter 80 into the Public and Private Port section, click Apply. • Scheduling should be set to Always so that the camera images can be accessed at any time. A check mark appearing before the entry name will indicate that the ports are enabled Important: Some ISPs block access to port 80.
13. Appendix F. Power Line Frequency COUNTRY Argentina VOLTAGE FREQUENCY 220V 50 Hz *Neutral and line wires are reversed from that used in Australia and elsewhere. *Outlets typically controlled by adjacent switch. Though nominal voltage has been officially changed to 230V, 240V is within tolerances and commonly found.
13. Appendix Spain 230V 50 Hz Sweden 230V 50 Hz Switzerland 230V 50 Hz Taiwan 110V 60 Hz Thailand 220V 50 Hz United Kingdom 230V* 50 Hz United States of America 120V 60 Hz *Outlets typically controlled by adjacent switch. Though nominal voltage has been officially changed to 230V, 240V is within tolerances and commonly found. G. 3GPP To use the 3GPP function, in addition to previous section, you might need more information or configuration to make this function work.
13. Appendix H. Enable UPnP of Windows XP Use the following steps to enable UPnP settings only if your operating system of PC is running Windows XP.
13.
13.
