Specifications
8
8 8
8 QUICK-SILVER™
OPERATION
TO ATTACH PLOW
!
!!
!Failure to follow installation and removal procedures may result in serious injury, death or damage to property.
Failure to follow installation and removal procedures may result in serious injury, death or damage to property.Failure to follow installation and removal procedures may result in serious injury, death or damage to property.
Failure to follow installation and removal procedures may result in serious injury, death or damage to property.
1. Make sure jack stand is set at proper height (See initial Jack Settings) and hitch extensions are level. (#10)
1. Make sure jack stand is set at proper height (See initial Jack Settings) and hitch extensions are level. (#10)1. Make sure jack stand is set at proper height (See initial Jack Settings) and hitch extensions are level. (#10)
1. Make sure jack stand is set at proper height (See initial Jack Settings) and hitch extensions are level. (#10)
2. Place latch cam handles in horizontal (down) position.
2. Place latch cam handles in horizontal (down) position.2. Place latch cam handles in horizontal (down) position.
2. Place latch cam handles in horizontal (down) position.
3. Pull up on latch tab to release handle. (#3)
3. Pull up on latch tab to release handle. (#3)3. Pull up on latch tab to release handle. (#3)
3. Pull up on latch tab to release handle. (#3)
4. Drive into plow until latch cams automatically engage the receiver rod. If plow attaches and latch cam handle moves fully
4. Drive into plow until latch cams automatically engage the receiver rod. If plow attaches and latch cam handle moves fully4. Drive into plow until latch cams automatically engage the receiver rod. If plow attaches and latch cam handle moves fully
4. Drive into plow until latch cams automatically engage the receiver rod. If plow attaches and latch cam handle moves fully
rearward (as in Diagram #9), go to step #5. If not, see #4a & #4b below
rearward (as in Diagram #9), go to step #5. If not, see #4a & #4b below rearward (as in Diagram #9), go to step #5. If not, see #4a & #4b below
rearward (as in Diagram #9), go to step #5. If not, see #4a & #4b below
a) If hitch extensions will not partially engage, then jack stand can be raised or lowered to allow engagement.
a) If hitch extensions will not partially engage, then jack stand can be raised or lowered to allow engagement. a) If hitch extensions will not partially engage, then jack stand can be raised or lowered to allow engagement.
a) If hitch extensions will not partially engage, then jack stand can be raised or lowered to allow engagement.
b) If hitch extensions are only partially engaged, then plug in electrics and place plow in float by holding the down
b) If hitch extensions are only partially engaged, then plug in electrics and place plow in float by holding the down b) If hitch extensions are only partially engaged, then plug in electrics and place plow in float by holding the down
b) If hitch extensions are only partially engaged, then plug in electrics and place plow in float by holding the down
control until float light is on. Once in float, check to see if jack stand needs to be raised or lowered and make
n
control until float light is on. Once in float, check to see if jack stand needs to be raised or lowered and make n control until float light is on. Once in float, check to see if jack stand needs to be raised or lowered and make n
control until float light is on. Once in float, check to see if jack stand needs to be raised or lowered and make necessary
ecessaryecessary
ecessary
adjustments. Then, repeat step #4
adjustments. Then, repeat step #4 adjustments. Then, repeat step #4
adjustments. Then, repeat step #4
5. Place lock pin (#5) through lock handle and lock tabs after plow is attached.
5. Place lock pin (#5) through lock handle and lock tabs after plow is attached.5. Place lock pin (#5) through lock handle and lock tabs after plow is attached.
5. Place lock pin (#5) through lock handle and lock tabs after plow is attached.
6. Connect power harness. (#6)
6. Connect power harness. (#6)6. Connect power harness. (#6)
6. Connect power harness. (#6)
7. Raise plow to full up position.
7. Raise plow to full up position.7. Raise plow to full up position.
7. Raise plow to full up position.
8. Raise jack stand by pulling spring loaded jack pin while pulling up on the jack positioning handle. Release spring loaded jac
8. Raise jack stand by pulling spring loaded jack pin while pulling up on the jack positioning handle. Release spring loaded jac8. Raise jack stand by pulling spring loaded jack pin while pulling up on the jack positioning handle. Release spring loaded jac
8. Raise jack stand by pulling spring loaded jack pin while pulling up on the jack positioning handle. Release spring loaded jack pin
k pin k pin
k pin
and allow jack to lock in the raised horizontal position.
and allow jack to lock in the raised horizontal position. and allow jack to lock in the raised horizontal position.
and allow jack to lock in the raised horizontal position.
INIT
INITINIT
INIT
NO
NONO
NO
the
thethe
the
1. F
1. F1. F
1. F
N
N N
N
2. A
2. A2. A
2. A
3. T
3. T3. T
3. T
4. C
4. C4. C
4. C
d
d d
d
Manual.pub
tile 1 of page 10
Cyan
Magenta
Yellow
Black
Cyan
Magenta
Yellow
Black
Friday, November 17, 2006 12:29