User Manual

Setting up guidance
Safety instructions
This product provides three function settings: measurement mode, tone switch,
temperature unit, etc.The comparison table of setting menu is as follows:
Human body temperature measurement
After the battery is installed, press the power on key for 1 second, and the
power on is completed after the full display self check.
5
Frontal temperature / object mode conversion settings
Setting of tone switch
Temperature unit conversion settings
●In the power on state, press and hold "set"
for 2 seconds, and F1 will be displayed on the
screen,then press the "+" or "-" button to
switch between "body temperature
measurement" / "object temperature
measurement".
●Shortcut switch mode: in the boot state,
short press "SET" key can realize the quick
switch of human temperature and object
temperature.
In the power on state, press and hold "set" for
2 seconds, and the screen displays F1,Press
the "set" key 1 time it will show F2.then press
the "+" or "-" key to switch between prompt
tone on and prompt tone off.
In the power on state, press and hold "set" for
2 seconds, and the screen displays F1,Press
"set" key 2 times, it will show F3, then press
the "+" or "-" key to switch between ° C and °
F
Manu
F1
“SET”Key “+”Key “-”Key
Press once
Tips TipsNo hint
Human
Temperature
Model
Object
Temperature
Model
Human
Temperature
Model
With prompt
sound
Function
Test
mode
Test
mode
Temperature
unit
F2
F3
Press again
Press again
℃ ℃℉
1.Before and after use, please keep the sensor and probe cavity clean.
2.Please place the forehead temperature gun in a temperature stable
environment for use. When ambient temperature changes greatly (e.g. from
indoor to outdoor), please place for about thirty minutes after measurement.
3.Do not begin to measure body temperature immediately after measuring the
temperature of an object at very high or very low temperature. Please place it
for ten minutes.
4.When the measurement object comes from a place that is quite different from
the measured ambient temperature, it should stay in the test environment for at
least five minutes.
5.Try not to measure in the forehead blowing, drenching water, sweating,
coating, smear cosmetics, etc. Do not take body temperature within 30 minutes
after exercise, bath, meal.
When the forehead temperature gun is out of working temperature, the screen
will prompt: after the boot complete self-test, the screen will show the ambient
temperature. When the working environment temperature is lower than 0℃ the
screen will display Err 1, backlight red, when the ambient temperature is higher
than 42℃, the screen will display Err 2, backlight red;
●Confirm that the measurement mode above the screen is body temperature
mode (non object temperature mode)
●Align the forehead temperature gun probe with the middle of the forehead and
keep it vertical, with a distance of about 3-5cm. Press the measurement key to
start the measurement. After about 1 second, the screen displays the
measurement value. Press the measurement key for 5 seconds to shut down
when no measurement is made, or shut down automatically after 30 seconds.
When 34℃≦T<37.3℃, bright green backlight.
When 37.4℃≦T≦38.0℃, bright yellow backlight.
When 38.1℃≦T≦42.9℃, bright red backlight.
When T<34℃, bright green backlight, display "LO"."
When T>42.9℃, bright red backlight, display "HI"."
Warm Tips
Object temperature measurement
● Adjust the temperature measurement mode to the body temperature.
●Aim the thermometer probe at the measuring target and keep it vertical, the
distance is about 3-5 cm press the measuring key, display the temperature after
about 1 second, when not measuring often press the measuring key for 5
seconds to shut down, or turn off automatically after 30 seconds.
Warm Tips
1.The range of measurement of the temperature measurement mode of the
object 0℃-100℃.
2. this function measures the object surface temperature and does not
represent the object core temperature.
6
Because the product is a reusable device, please pay attention to the cleaning
process after use;
Please keep the inner cavity of sensor and probe clean, otherwise it will affect
the measurement accuracy. Surface cleaning: wipe dirt with clean soft cloth or
cotton stick with a little medical spray.
Clean the inner cavity of the sensor and probe: gently wipe the inner cavity of
the head or the top of the sensor with a clean soft cloth or cotton stick with a little
medical sprinkler. When the alcohol is completely volatile.
Product maintenance and maintenance methods
Storage conditions, methods
Transport conditions, methods
Quality commitment and after-sale service
3.The emissivity of different materials may be different (refer to the emissivity of
materials), and the measured temperature will deviate slightly from the actual
temperature.
4.When the measured value is less than 0℃, bright red backlight, display "LO"..
5.When the measurement is higher than 100℃, bright red backlight, display
"HI"..
Products must be kept clean and kept in a dry place. Don't put the electronic
forehead temperature gun in a place with electric shock. do not store the
electronic forehead temperature gun in an extreme temperature environment
above 55℃ or below -10℃ and humidity above 85%.
The transportation process should prevent rain, heavy fall and so on, can not be
transported in the extreme temperature environment above 55℃ or below -10
℃, humidity above 85%.
This product provides one year free maintenance service.
Note: No free maintenance service will be provided for any damage caused by
the user's personal cause of failure or tampering.
Enterprise Name:Zhengzhou AiQURA Intelligent Technology Co., Ltd.
Address:4th Floor, Building 26, Smart phone industrial park,
Intersection of xingang Avenue and Renmin road,
Zhengzhou airport economic comprehensive experimental zone.
7 8
Warranty card
(customer retention)
type/specification
machine serial number/batch number
purchase date
address
site seal
service tel
Maintenance record
The matters Maintenance staff
note
Please show this card when the machine is under
warranty!
Customer credit card
(retained by the manufacturer)
1. Product information
Model/specification
Number/lot number of the device
Store address province city (county)
2.customer information
Customer names
birth
Address
Contact phone number
zip codes
note
3. Store information
Salesperson's name
tel